Related Manuals for Extron electronics XTP T HD 4K
Summary of Contents for Extron electronics XTP T HD 4K
- Page 1 User Guide XTP Extenders XTP T HD 4K XTP R HD 4K XTP 4K Transmitter and XTP 4K Receiver 68-2716-01 Rev. A 01 17...
-
Page 2: Safety Instructions
Safety Instructions Safety Instructions • English Istruzioni di sicurezza • Italiano AVVISO: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente WARNING: This symbol, , when used on the product, is intended to della presenza di tensione non isolata pericolosa all’interno del contenitore alert the user of the presence of uninsulated dangerous voltage within the del prodotto che può... - Page 3 より 『Extron Safety www.extron.com and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください。 Copyright © 2017 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ( ), registered service marks ( ), and trademarks (™) are the property of RGB Systems, Inc.
- Page 4 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 5 Conventions Used in this Guide Notifications The following notifications are used in this guide: Potential risk of severe injury or death. WARNING: AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.
-
Page 7: Table Of Contents
HDMI Audio Switch .......... 17 Tabletops ............41 EDID ..............17 Furniture ............41 Audio Output Overview ........18 Racks ............41 Reset Modes ............ 19 Firmware Download .......... 42 XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Contents... - Page 8 XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Contents viii...
-
Page 9: Introduction
In this guide, the terms “transmitter” and “XTP T HD 4K” refer to the XTP T HD 4K transmitter. The terms “receiver” and “XTP R HD 4K” refer to the XTP R HD 4K receiver. Product Descriptions The XTP T HD 4K and XTP R HD 4K enable extension of video, audio, bidirectional control, and Ethernet signals over a single shielded twisted pair cable. -
Page 10: System Compatibility
Certain features can also be controlled through an XTP matrix switcher (see the XTP matrix switcher user guide at www.extron.com). NOTE: If the XTP T HD 4K or XTP R HD 4K is connected to an XTP matrix switcher, configure it through the XTP matrix switcher (see the XTP matrix switcher user guide for SIS commands or the XTP System Configuration Help File for software details). -
Page 11: Video Features
Extron XTP System Configuration Software compatibility — Allows for easy setup and commissioning. Two relays for controlling room functions (receiver only) — Enables control of • lighting, screen settings, and other device functions. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Introduction... -
Page 12: General Features
Highly reliable, energy-efficient external universal power supply included — • Provides worldwide power compatibility, with high demonstrated reliability and low power consumption for reduced operating costs. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Introduction... -
Page 13: Installation
Installation This section contains the installation procedures and details for the XTP T HD 4K and XTP R HD 4K. Topics in this section include the following: • Rear Panel Connectors • Connection Details Rear Panel Connectors Transmitter Rear Panel Connectors... - Page 14 LAN connector — Connect a control or controlled device to the pass-through LAN connector for 10/100Base-T Ethernet communication. LEDs on the connector indicate link and activity status. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation...
-
Page 15: Receiver Rear Panel Connectors
XTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée en extérieur (voir Remote power à la page 15). XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... - Page 16 S/PDIF output): The audio format selected on the source material or device. • The source device automatically outputting an audio format through EDID. • XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation...
-
Page 17: Connection Details
Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... -
Page 18: Twisted Pair Cable Termination And Recommendations For Xtp Communication
Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and power injectors. If these pass-through points are required, use shielded couplers and punch down connectors. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... -
Page 19: Twisted Pair Cable Termination For Pass-Through Ethernet Communication
White-blue White-blue Side View Insert Twisted Green Green Orange Green Pair Wires White-brown White-brown White-brown White-brown RJ-45 Connector Brown Brown Brown Brown Figure 8. RJ-45 Pin Assignment XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... -
Page 20: Rs-232 And Ir Over Xtp Communication
• Ne pas étamer les câbles. Les câbles étamés ne sont pas aussi bien fixés dans les terminaisons des connecteurs à vis captives et pourraient sortir. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... -
Page 21: Power Connection
3/16” (5 mm) Max. Smooth Ridges Power Supply Output Cord Figure 10. Power Wiring See the notifications on the next page for local power information and considerations. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... - Page 22 La longueur idéale est de 5 mm (3/16 inch). TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation...
-
Page 23: Remote Power
XTP à distance ne peut être routée en extérieur. Power injector To power the XTP T HD 4K or XTP R HD 4K remotely with an XTP Power Injector, power one device locally (see Local power... -
Page 24: Operation
Hotline. See the contact numbers on the last page of this guide for the nearest Extron office. This section contains information about the local operation of the XTP T HD 4K and XTP R HD 4K as well as the operational indicators. Topics in this section include the following: •... -
Page 25: Receiver Front Panel Features
SIS commands or the XTP System Configuration Software. EDID The XTP T HD 4K can record and save EDID in a user memory location on the transmitter. EDID can come from the loop-through display on the transmitter or the output display on the receiver. -
Page 26: Audio Output Overview
Audio Output Overview By default, the XTP T HD 4K prioritizes embedded digital audio over analog audio to send over the XTP communication. Use SIS commands (see SIS Configuration and Control page 20) or the XTP System Configuration Software (see Configuration Software page 28) to manually select the audio input. -
Page 27: Reset Modes
(mode 5) page 25 or the receiver • The rear panel Power LED Reset mode blinks four times in quick command on page 27). succession during the reset. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Installation... -
Page 28: Sis Configuration And Control
SIS Configuration and Control This section contains SIS communication details and SIS commands and responses when the host device is connected directly to an XTP T HD 4K or XTP R HD 4K. Topics in this section include the following: •... -
Page 29: Command And Response Table Overview
= Carriage return with no line feed = Pipe (can be used interchangeably with the character). • = Space = Escape key = Can be used interchangeably with the character. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control... -
Page 30: Command And Response Tables For The Transmitter Sis Commands
Command and Response Tables for the Transmitter SIS Commands The following commands are for direct connection to the XTP T HD 4K (see the XTP matrix switcher user guide for commands sent from the matrix switcher to the transmitter). Command... -
Page 31: Edid Commands
EDID information from the display connected to the transmitter loop-through connector EDID information from the display connected to the receiver output User assigned * = default XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control... -
Page 32: Advanced Configuration Commands
= input reports as an HDCP Authorized device (default) = disabled (default) = Test pattern = 720p @ 50 Hz = 720p @ 60 Hz = 1080p @ 60 Hz XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control... - Page 33 = Output HDCP status = sink device detected but the output signal is not encrypted = sink device detected and the output signal is encrypted XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control...
-
Page 34: Command And Response Tables For The Receiver Sis Commands
95.5% 31.0% 64.0% 97.0% 32.5% 65.5% 98.5% 34.0% 67.0% 100.0% 35.5% 68.5% = unmute all (default) X1& = Audio output mute = mute all XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control... -
Page 35: Advanced Configuration Commands
= 16 ms) = Pulse time 65,535 = open (default) = Relay status = close = unmute = Video mute = mute video to black XTP T HD 4K Transmitter and XTP R HD 4K Receiver • SIS Configuration and Control... -
Page 36: Configuration Software
This section contains installation and configuration procedures for the XTP System Configuration Software to directly configure and control the XTP T HD 4K and XTP R HD 4K. Either device can also be configured and controlled remotely through the XTP System Configuration Software and the XTP matrix switcher (see the XTP System Configuration Software Help file). - Page 37 Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
-
Page 38: Software Product Page
Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software... -
Page 39: Software Connection
Software Connection To connect the software directly to the XTP T HD 4K or XTP R HD 4K, connect the computer running the software to the configuration connector (see figure page 16 or figure on page 17). Figure 18. Connections Screen To connect to a device: Open the XTP System Configuration Software. -
Page 40: Software Operation
XTP T HD 4K or XTP R HD 4K. See an XTP matrix switcher user guide (www.extron.com) for more information on these features. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software... -
Page 41: Update Firmware
. The Tools Software Preference Software Preference dialog box opens. Figure 23. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software... - Page 42 From the menu, select Help Help Extron Website This option opens the Extron website in a web browser. From the menu, select Help Extron Website XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
-
Page 43: Transmitter Configuration
XTP receiver or XTP matrix switcher or deselect it to stop transmitting a test pattern to an XTP receiver or XTP matrix switcher. If selected, also select a signal type from the drop-down menu. Signal Type XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software... - Page 44 Audio only — Displays whether only audio is sent to outputs. Analog Audio Gain — Displays the gain for analog audio. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
- Page 45 . The EDID file appears in the Open panel ( Available EDID Assign the EDID file from the panel to import the EDID to the device. Available EDID XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
- Page 46 Connected Outputs listing the EDID settings common among the selected outputs. Select the desired common EDID. The EDID is shown in the panel. Available EDID XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
-
Page 47: Receiver Configuration
Force analog audio output — For connected DVI displays, click the Force analog check box to output analog audio. audio output when DVI display is connected XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software... - Page 48 S/PDIF output. Analog Audio — Displays the mute status of the analog audio output. Analog Audio Volume — Displays the analog audio output volume level. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • XTP System Configuration Software...
-
Page 49: Reference Information
• Firmware Download Mounting The XTP T HD 4K and XTP R HD 4K can be placed on a tabletop or mounted in a rack or underneath a desk. Tabletops Attach the provided rubber feet to the bottom four corners of the enclosure. -
Page 50: Firmware Download
Click the link ( ) to the right of the desired product. Download Submit any required information to start the download. Note where the file is saved. XTP T HD 4K Transmitter and XTP R HD 4K Receiver • Reference Information... - Page 51 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.