Page 3
MITAC assumes no liability whatsoever, and ® disclaims any express or implied warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or merchantability. MITAC retains the right to make changes to produce descriptions and/or specifications at any time, without notice.
Page 4
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada. Notice for Europe (CE Mark) ● This product is in conformity with the Council Directive 2014/30/EU and 2014/35/EU. http://www.tyan.com...
Page 5
Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations. VCCI-A ● この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨 害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要 求されることがあります。 VCCI-A Safety: IEC/EN 60950-1 ● This equipment is compliant with CB/LVD of Safety: IEC/EN 60950-1. http://www.tyan.com...
How this guide is organized This guide contains the following parts: Chapter 1: Overview This chapter provides an introduction to the TYAN FT48T-B7105 barebones and standard parts list, describes the external components, gives an overview of the product from different angles.
Safety and Compliance Information Before installing and using TYAN FT48T-B7105, take note of the following precautions: ·Read all instructions carefully. ·Do not place the unit on an unstable surface, cart, or stand. ·Do not block the slots and opening on the unit, which are provided for ventilation.
You must become familiar with the safety information in this guide before you install, operate, or service TYAN products. Symbols on Equipment Caution. This symbol indicates a potential hazard.
Page 9
· Make sure racks are coupled together if it is a multiple-rack installation. · Make sure the rack is level and stable before installing an appliance in the rack. · Make sure the leveling jacks are extended to the floor. http://www.tyan.com...
Page 10
If you do not ground the Green/Yellow tab, it can cause an electrical shock due to high leakage currents. · Do not place objects on AC power cords or cables. Arrange them so that no http://www.tyan.com...
Page 11
TYAN, your authorized TYAN partner, or their agents. Equipment Modifications · Do not make mechanical modifications to the system. TYAN is not responsible for the regulatory compliance of TYAN equipment that has been modified.
Page 12
– Liquid has been spilled on the product or an object has fallen into the product. – The product has been exposed to rain or water. – The product has been dropped or damaged. – The product does not operate normally when you follow the operating instructions. http://www.tyan.com...
IT demand but also offers a smooth path for future application usage. ® TYAN also offers the FT48T-B7105 in a version that can support up to four 3.5”/2.5” hot-swap SSD/HDD. The FT48T-B7105 uses TYAN’s latest chassis featuring a robust structure and a solid mechanical enclosure. All of this provides FT48T-B7105 the power and flexibility to meet the needs of nowadays server application.
Product Models The system board within the Tyan Barebone is defined by the following models: B7105F48TV4HR-2T-N : Intel-based platform B7105F48TV4HR-2T-G : Intel-based platform SKU Differences Model Name FT48T-B7105 SKU Name B7105F48TV4HR-2T-N B7105F48TV4HR-2T-G PCIe Air duct CPU Air duct...
Features TYAN FT48T-B7105 (B7105F48TV4HR-2T-N) Net weight 34 kg (75 lbs) Form Factor 4U Tower Chassis Model FT48T System Dimension (D x W x 27.5" x 16.8" x 6.9" (700 x 427 x 176mm) Motherboard S7105AGM2NR-2T Gross Weight 40 kg (88.5 lbs)
Page 18
(2) 10GbE ports, Port Q'ty (1) GbE port dedicated for IPMI Controller Intel X550-AT2 Realtek RTL8211E Connector (2) SATA Controller Intel C621 SATA Speed 6.0 Gb/s RAID 0/1/10/5 (Intel Storage RAID RSTe) (2) Mini-SAS HD Connector (8-ports) sSATA Controller Intel C621 http://www.tyan.com...
Page 19
24-bit high quality video AST2500 IPMI compression, 10/100/1000 Mb/s Feature MAC interface Onboard Chipset Onboard Aspeed AST2500 Brand / ROM size AMI, 32MB Hardware Monitor, SMBIOS BIOS 3.0/PnP/Wake on LAN, Boot from Feature USB device/PXE via LAN/Storage, User Configurable FAN PWM Duty http://www.tyan.com...
Page 20
In/Non-operating 90%, non-condensing at 35° C Humidity RoHS RoHS 6/6 Compliant Manual (1) Quick Installation Guide Installation CD (1) TYAN Device Driver CD (1) FT48T-B7105 w/NV Package Contains Barebone Tesla-aware FW Barebone For rackmount solution, please Others contact Tyan sales...
Page 21
Thermal Design Max up to 205W Power (TDP) wattage Chipset Intel C621 Supported DIMM (6)+(6) DIMM slots DDR4 RDIMM/RDIMM DIMM Type / Speed Memory 3DS/LRDIMM/LRDIMM 3DS 2666 Up to 384GB RDIMM/ 768GB Capacity LRDIMM/ 1,536GB RDIMM 3DS/LRDIMM 3DS *Follow latest http://www.tyan.com...
Page 22
D-Sub 15-pin Graphic Resolution Up to 1920x1200 Chipset Aspeed AST2500 (2) USB3.0 ports (at rear), (2) USB3.0 ports (at front) (1) D-Sub 15-pin port I/O Ports Audio (2) 10GbE ports, RJ-45 (1) GbE dedicated for IPMI Others ID LED http://www.tyan.com...
Page 23
Class A Operating Temp. 10° C ~ 35° C (50° F~ 95° F) Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F) Operating Environment In/Non-operating 90%, non-condensing at 35° C Humidity RoHS RoHS 6/6 Compliant http://www.tyan.com...
Page 24
Manual (1) Quick Installation Guide Installation CD (1) TYAN Device Driver CD Package Contains Barebone (1) FT48T-B7105 Barebone For rackmount solution, please Others contact Tyan sales NOTE: 1. The specifications are subject to change without prior notice. 2. Please visit our Web site for the latest information.
Standard Parts List This section describes FT48T-B7105 package contents and accessories. Open the box carefully and ensure that all components are present and undamaged. The product should arrive packaged as illustrated below. 1.4.1 Box Contents FT48T-B7105 Box Content 4U barebone, (4) hot swap HDD bays ...
About the Product The following views show you the product. 1.5.1 System Front View http://www.tyan.com...
Page 27
Linking / Solid On Ready / Off #7 HDD LED Amber Access / Blinking System Normal / Off #8 Warning LED Amber System Warning / Solid On System Power On / Solid On #9 Power LED Green System Power Off / Off http://www.tyan.com...
Page 28
Drive State (Green) (Red) Drive present, no activity Green Solid On Drive present, with activity Green Blinking Drive Failed Don’t care Red Solid On Drive dentify Don’t care Red Blinking @1 Hz Drive Rebuild Don’t care Red Blinking @4 Hz http://www.tyan.com...
1.5.2 System Rear View PSU0 IPMI Port PSU1 LAN2 LAN1 LINE-OUT VGA Port LINE-IN ID LED USB3.0 Port2 Expansion Slots USB3.0 Port1 http://www.tyan.com...
Page 30
Green Solid On Green Solid On 100 Mbps Active Green Blinking Green Solid On Link 1000 Mbps Green Solid On Amber Solid On (1Gbps) Active Green Blinking Amber Solid On NOTE: “Left” and “Right” are viewed from the rear panel. http://www.tyan.com...
Page 31
AC present Only 12VSB on (PS off) or PS in Smart Green Blinking Redundant state @1Hz Output ON and OK Green Solid ON AC cord unplugged or AC power lost with a second Amber Solid ON power supply in parallel still with AC input power http://www.tyan.com...
To avoid damaging the motherboard and associated components, do not use torque force greater than kgf/cm (4.35 ~ 6.09 lb/in) on each mounting screw for motherboard installation. Do not apply power to the board if it has been damaged. http://www.tyan.com...
Working on a system that is connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to FT48T-B7105 or injury to yourself. Ground yourself properly before removing the top cover of the system.
This section describes how to install components on to the motherboard, including CPUs, memory modules, SSD/HDD and PCI-E cards. 2.1.1 Removing the Chassis Cover Follow these instructions to remove the FT48T-B7105 chassis cover. Loosen one screw and two thumb screws to slide the top cover off. http://www.tyan.com...
Page 38
Unscrew to remove the CPU air duct from the chassis. http://www.tyan.com...
Opening the Chassis Front Bezel Follow these instructions to open the chassis front bezel. Insert the front bezel key (packed in a bag in the accessory box) and rotate the key 90 degrees counterclockwise to unlock the front bezel. Open the front bezel. http://www.tyan.com...
Follow the steps below on installing CPUs and CPU heatsinks. Align and install the processor on the carrier. Carefully flip the heatsink. Then install the carrier assembly on the bottom of the heatsink and make sure the guide pin is located in the correct direction. http://www.tyan.com...
Page 41
Carefully flip the heatsink. Align the heatsink with the CPU socket by the guide pin and make sure the guide pin is located in the correct direction. Then place the heatsink onto the top of the CPU socket. http://www.tyan.com...
Page 42
(1234). NOTE: When disassembling the heatsink, loosen the screws in reverse order (4321). Repeat the procedures described earlier to install the second processor and heatsink. Place the CPU air duct back and screw it to the chassis. http://www.tyan.com...
2.1.4 Installing the Expansion Cards Follow the instructions to install the expansion cards. Locate the PCI-E Gen.3 slots on the motherboard. Unscrew to take out the dummy brackets. Screw the GPU bracket to the GPU card. http://www.tyan.com...
Page 44
Locate the guide pins of the GPU air duct. Place the GPU air duct on the chassis wall. Insert the GPU card into the PCIE Gen. 3 slot and screw the GPU card to the chassis. http://www.tyan.com...
Page 45
Connect the GPU Power cable. Replace the GPU air duct and screw it to the Mid-bar. http://www.tyan.com...
Align the memory module with the slot. When inserted properly, the memory slot locking levers lock automatically onto the indentations at the ends of the module. Follow the recommended memory population table to install the other memory modules. http://www.tyan.com...
2.1.6 Installing Hard Drives The FT48T-B7105 can support up to four (4) 3.5”/2.5” SSD/HDD. Follow these instructions to install a hard drive. Warning!!! Always install the hard disk drive to the chassis after the chassis is secured on the rack.
Page 50
2.5” SSD/HDD Turn over the HDD unit and secure the SSD/HDD using 4 HDD screws. Reinsert the HDD tray into the chassis and press the locking lever to secure the tray. Close the front bezel. http://www.tyan.com...
Follow these instructions to install the DVD-ROM. Take out the DVD-ROM Kit. Assemble the DVD Rail-L and Rail-R to the DVD device and secure with 8 screws. Open the front bezel, and select the device tray where to insert the DVD-ROM. http://www.tyan.com...
Page 52
Unscrew to remove the selected device tray as shown below. Install the DVD-ROM into the chassis. http://www.tyan.com...
Page 53
Connect the SATA cable to the motherboard and route the cable along the side of the chassis. Connect the DVD-ROM PWR cable to the Power Distribution Board. Connect the SATA cable and PWR cable to the DVD-ROM device. http://www.tyan.com...
A: Nut for M6 screw --- 10 pcs B: M6--10 pcs 2.3.1 Installing the FT48T-B7105 in a Rack Follow these instructions to mount the TYAN FT48T-B7105 into an industry standard 19” rack. NOTE: Before mounting the TYAN FT48T-B7105 in a rack, ensure that all internal components have been installed and that the unit has been fully tested.
Page 57
Screw the mounting ears to the FT48T-B7105 as shown using six M4-L5 screws (black). Left Right Press the latch to draw out the inner rails from each rail assembly. Install the inner sliding rail to each side of the server using five M4-L5 screws.
Page 58
Secure the outer rails to the rack using four M6 (2 front, 2 rear) screws (B) and five nut (3 front, 2 rear) (A) for each side. Secure the mounting brackets from outside, not inside of the rack. http://www.tyan.com...
Page 59
Rack Mounting the Server Lift the unit and then insert the inner slide rails into the middle rails. Push the whole system in. http://www.tyan.com...
Page 60
Secure the mounting ears to the rack using two M6 screws (B). Push the latch on both sides of the chassis simultaneously to pull the system out. http://www.tyan.com...
This chapter explains how to replace the pre-installed components, including the S7105 Motherboard, M1019-FPB Front Panel Board, M1237F48-BP6-4 SATA/SAS HDD Backplane Board, M1809F77A-FB Fan Board, M1622F48T-D-PDB Power Distribution Board, System Fan and Power Supply Unit etc. 3.0.2 Disassembly Flowchart The following flowchart outlines the disassembly procedures. http://www.tyan.com...
Removing the Cover Before replacing any parts you must remove the chassis cover. Follow Section 2.1.1 Removing the Chassis Cover (page 37) to remove the cover of the FT48T-B7105. Replacing the System Fan Follow these instructions to replace the system fan.
Replacing the Fan Board Follow these instructions to replace the fan board. Unscrew the fan cage and remove all system fans and from the fan cage. Take out the fan cage. Disconnect all cables from the fan board. http://www.tyan.com...
Page 64
Unscrew the fan board to replace with a new one. Assemble the fan cage and system fans back into the chassis following the steps described earlier in reverse. http://www.tyan.com...
3.3.1 Fan Board Features M1809F77A-FB Fan Board Form Factor W81.4 x L312.28 (mm), 4-layer PCB (4) Big 4P Power Connector (J7/J9/J10/J11) Specifications (6) 2x2-pin FAN Connector (J1/J2/J3/J4/J5/J6) (1) 2x10-pin TYAN Barebone FAN Connector (J8) FAN Sequence http://www.tyan.com...
Replacing the Fan Board on how to remove the Fan Cage and Fan Board. Disconnect all cables attached to the HDD BP Board and unscrew to take it out. Prepare a new HDD BP Board and reinstall it into the chassis following the steps in reverse. http://www.tyan.com...
Replacing the Front Panel Board Follow these instructions to replace the M1019-FPB Front Panel Control Board. Disconnect the power cable and data cable from M1019. Pull up the latch and slide the LED control board unit out of the chassis. http://www.tyan.com...
Page 71
Remove three screws securing the mylar and LED control board to the bracket. Lift up the mylar and LED control board free from the chassis. After replacement, insert the unit into the chassis following the above procedures in reverse. http://www.tyan.com...
Power Button Warning LED (red) Reset Button Power LED (green) NMI Button ID Button ID LED (blue) USB3.0 Port 2 LAN2 LED (green) USB3.0 Port 1 LAN1 LED (green) Front Panel Connector (J3) HDD LED (amber) USB3.0 Connector (J34) http://www.tyan.com...
Pull the lever to a fully open position. Press and hold the latch to pull the power supply out. After replacing a new power supply, press and hold the latch to push the power supply back into the chassis. http://www.tyan.com...
Follow these instructions to replace the M1622F48T-D-PDB Power Distribution Board. Disconnect all cables connected to the PDB. Unscrew the power distribution board to lift it up for replacement. Follow the steps described earlier in reverse order to reinstall the power distribution board into the chassis. http://www.tyan.com...
Refer to the sections described earlier to remove all cables and components on the motherboard. Unscrew the motherboard. Carefully lift the motherboard from the chassis. Prepare a new motherboard and follow the steps described earlier in reverse order to reinstall the motherboard into the chassis. http://www.tyan.com...
UEFI recovery bootloader that would prevent the recovery process itself from working. In no event shall Tyan be liable for direct, indirect, incidental, special or consequential damages arising from the BIOS update or recovery.
Page 80
“Flash update completed. Press any key to reset the system” displayed on screen. Remove the USB disk and reboot. If your system does not have video output or the POST code halts at “FF” on the right-lower portion of the screen, please contact Tyan representatives for RMA service. http://www.tyan.com...
Follow these instructions to install the Power Wire Clip. Press the lever to pull the clip to the right. Insert the Power Wire Clip into the Power Wire Clip Jack. Plug in the AC Power Cord. Press to lock the clip and push the clip forwards. http://www.tyan.com...
FAN BP Connect to Fan BP PWR → J9, J7, J10 & J11 PW3 & PW5 Cable 4. HDD BP PWR Cable HDD BP to PDB HDD BP Connect to 2x2P to B4P → J35 & J36 PWR Cable http://www.tyan.com...
Page 84
Cable 2x4P PWR → PW13 PWCN2 Cable-1 2x4P PWR → PWCN3 Cable-2 → PSMI Cable JPSMI1 PSMI NOTE: Please note the thermal design power (TDP) of GPU must be less than 250W or OCP (over current protect) will occur. http://www.tyan.com...
The red spot indicates the sensor. Fan and Temp Sensor Location: Fan Sensor: It is located in the third pin of the fan connector, which detects the fan speed (rpm) Temp Sensor: refer to Figure 1: Sensor Location. They detect the system temperature around. http://www.tyan.com...
Page 86
BIOS Temp Sensor Name Explanation: http://www.tyan.com...
Page 87
The Max Temperature of CPU1 MOSFET The Max Temperature of CPU0 DIMM Area1 MOSFET P0_DIMM_MOS_1 The Max Temperature of CPU0 DIMM Area2 MOSFET P0_DIMM_MOS_2 The Max Temperature of CPU1 DIMM Area1 MOSFET P1_DIMM_MOS_1 The Max Temperature of CPU1 DIMM Area2 MOSFET P1_DIMM_MOS_2 http://www.tyan.com...
Page 88
Temperature of GPU4 Core0 Slot GPU4_Core1_ TEMP Temperature of GPU4 Core1 Slot SYS_FAN_1 Fan Speed of SYS_FAN_1 SYS_FAN_2 Fan Speed of SYS_FAN_2 SYS_FAN_3 Fan Speed of SYS_FAN_3 SYS_FAN_4 Fan Speed of SYS_FAN_4 SYS_FAN_5 Fan Speed of SYS_FAN_5 SYS_FAN_6 Fan Speed of SYS_FAN_6 http://www.tyan.com...
Appendix V: FRU Parts Table FT48T-B7105 FRU Parts Model Item Part Number Picture Description Number Power Supply FRU-PS-0230 471100000319 2000W PSU 4800RPM,120*120*38mm,4PIN fan CFAN-0410 541379090002 (FAN Q’ty 3pcs) Heatsink & Cooler FRU-TH-0220 434T56600001 Heatsink Rack Mounting Parts CRAL-0070 340746600010 28” Slide Rail Kit...
MITAC serves multiple market segments with the industry’s most competitive services to support them. Please feel free to contact us directly for this service at tech-support@tyan.com Help Resources: 1. See the beep codes section of this manual.
Page 92
(RMA) number. The RMA number should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you. TYAN® FT48T-B7105 Service Engineer’s Manual V1.0 Document No.: D2413-100...