Download Print this page

Empire Comfort Systems LS48THF-1 Installation Instructions And Owner's Manual

Logs and rocks set / log set for use with direct vent fireplace models dvll48bp92n-1/ dvll48bp92p-1

Advertisement

LS48THF-1
LOGS AND ROCKS SET
This decorative media set includes an unusual
assortment of logs and rocks in varying textures
and colors to complement your linear fireplace -
plus stainless steel coils to add a unique flair.
For ease of installation, unpack all pieces and lay
out so that any identifying letters are visible.
WARNINGS
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from
neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the
fire department.
INSTALLATION INSTRUCTIONS
AND
OWNER'S MANUAL
LOG SET FOR USE WITH
DIRECT VENT FIREPLACE
MODELS:
DVLL48BP92(N,P)-1
GAS-FIRED
INSTALLER:
Leave this manual with the appliance.
CONSUMER: Retain this manual for future
reference.
WARNING: If not installed, operated and maintained
in accordance with the manufacturer's instructions,
this product could expose you to substances in fuel
or from fuel combustion which can cause death or
serious illness.
Page 1

Advertisement

loading

Summary of Contents for Empire Comfort Systems LS48THF-1

  • Page 1 INSTALLATION INSTRUCTIONS OWNER’S MANUAL LS48THF-1 LOG SET FOR USE WITH LOGS AND ROCKS SET DIRECT VENT FIREPLACE MODELS: This decorative media set includes an unusual DVLL48BP92(N,P)-1 assortment of logs and rocks in varying textures and colors to complement your linear fireplace - plus stainless steel coils to add a unique flair.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS SECTION PAGE Important Installation Guidelines ................3 General Information ....................3 Rock Identification ....................4 Log Identification ......................5 Rock and Log Placement ..................6 - 22 Master Parts Distributor List ...................23 How To Order Repair Parts ..................23 HARDWARE PACK R12061 (QUANTITY 12) 8-32 X 3/4”...
  • Page 3: Important Installation Guidelines

    IMPORTANT INSTALLATION GUIDELINES Before You Begin CAUTION: Do not place crushed glass around the pilot It is recommended that prior to installing the LS48THF Logs and assembly. Crushed glass must be placed on the burner screen Rock Kit, test fire the fireplace to make sure it is operational. in a single layer.
  • Page 4: Rock Identification

    ROCK IDENTIFICATION DESCRIPTION & TOP VIEW FRONT VIEW PART NUMBER Rock A 35777 Rock B 35778 Rock E 35781 Rock F 35782 Rock G 35783 Rock H 35784 Rock I 35785 Rock J 35786 Page 4 36474-0-0316...
  • Page 5: Log Identification

    LOG IDENTIFICATION DESCRIPTION & TOP VIEW FRONT VIEW PART NUMBER Log L 35788 Log M 35789 Log N 35790 Log O 35791 Log P 35792 Log Q 35793 36474-0-0316 Page 5...
  • Page 6: Rock And Log Placement

    ROCK AND LOG PLACEMENT Tools Needed: NOTE: Once the installation is complete with the logs, rocks, Protective Gloves and crushed glass media in place, operate the fireplace to verify Phillips Screw Driver or Power Drill with Phillips Drive flame appearance. If there are flames directly impinging a log, turn off fireplace, then remove the crushed glass media directly Before you begin: Do not, handle these logs with your bare below where the flame impingement occurred.
  • Page 7 ROCK AND LOG PLACEMENT Place Rock A onto Burner Pins 1 and 2. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 7...
  • Page 8 ROCK AND LOG PLACEMENT Place Rock J onto Burner Pin 3. TOP VIEW FRONT VIEW Page 8 36474-0-0316...
  • Page 9 ROCK AND LOG PLACEMENT Place Rock E onto Burner Pin 4. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 9...
  • Page 10 ROCK AND LOG PLACEMENT Place Rock F between Burner Pins 6 and 7. Do not place the rock over the burner screen. See image below for proper placement. TOP VIEW FRONT VIEW Page 10 36474-0-0316...
  • Page 11 ROCK AND LOG PLACEMENT Place Rock G onto Burner Pin 8. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 11...
  • Page 12 ROCK AND LOG PLACEMENT Place Rock H Burner Pins 8 and 7. See image below for proper placement. TOP VIEW FRONT VIEW Page 12 36474-0-0316...
  • Page 13 ROCK AND LOG PLACEMENT Place Rock I over the right side of Rock H. See image below for proper placement. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 13...
  • Page 14 ROCK AND LOG PLACEMENT Place Rock B onto pin on Rock J and rear of burner cover. See image below for proper placement. TOP VIEW FRONT VIEW Page 14 36474-0-0316...
  • Page 15 ROCK AND LOG PLACEMENT Place Log L onto pin on Rock A and angle to rest on the left rear portion of the burner cover. Log L should be placed against the rear liner. See image below for proper placement. TOP VIEW FRONT VIEW Burner Pin Locations...
  • Page 16 ROCK AND LOG PLACEMENT 10. Place Log M onto the pin on Log L. Angle it across the burner screen and towards the front of the burner pan. See image below for proper placement. TOP VIEW FRONT VIEW Page 16 36474-0-0316...
  • Page 17 ROCK AND LOG PLACEMENT 11. Place Log N on Burner Pin 7 and pin on Rock H. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 17...
  • Page 18 ROCK AND LOG PLACEMENT 12. Place Log O on Burner Pin 5 and pin on Rock E. TOP VIEW FRONT VIEW Page 18 36474-0-0316...
  • Page 19 ROCK AND LOG PLACEMENT 13. Place Log P on pin on Log O and angle down to front of burner pan. See image below for proper placement. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 19...
  • Page 20 ROCK AND LOG PLACEMENT 14. Place Log Q on Burner Pin 6 and pin on Rock F. TOP VIEW FRONT VIEW Page 20 36474-0-0316...
  • Page 21 ROCK AND LOG PLACEMENT 15. Place metal curls as shown in the image below. TOP VIEW FRONT VIEW Burner Pin Locations 36474-0-0316 Page 21...
  • Page 22 ROCK AND LOG PLACEMENT Rock and Log Placement is complete. TOP VIEW FRONT VIEW COMPLETING INSTALLATION Crushed Glass Media Final Steps Place crushed glass media onto the burner cover, burner Re-install the glass door assembly. Test fire to ensure there screen and accent glass panels.
  • Page 23: Master Parts Distributor List

    This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com. Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equip- ment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc. Dey Distributing Victor Division of F.
  • Page 24 Empire Comfort Systems Inc. 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. www.empirecomfort.com Page 24 36474-0-0316...