Cables; Assembly; Starting And Stopping - Flymo GLIDER G330 Original Instructions Manual

CABLES - IMPORTANT
• Use only 1.00mm 2 size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm 2 size cable, 10 amps 250 volts AC.
• YOUR PRODUCT IS SUPPLIED WITH CABLE
WIRED DIRECTL Y INTO THE PRODUCT.
1. If the supply cord is damaged, it must be replaced by
your local Husqvarna UK Ltd. Approved Service Centre
or similarly qualified persons in order to avoid a hazard.
2.Flymo Extension Cables are available from your
local Husqvarna UK Ltd. Approved Service Centre.
3.Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd.
Approved Service Centre for further information on the
connectors and kits available.
4.Only use extension cables specifically designed for
outdoor use.
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not
be left outside permanently nor should they be sub-
merged or immersed in water. Do not let cable lay or
trail through pools of water or splashed with water
from hose pipes.
A
B
D
1
F

Cables

Assembly

Starting and Stopping

C
E
1
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.
1.No earth required. Flymo products are double insu-
lated to EN60335 and under no circumstances should
an earth be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be con-
nected to the Terminal which is marked with the letter
'L' or coloured RED.
4.It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5.If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6.A 13 Amp fuse must be fitted to the Mains Plug.
7.The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
Preparing your lawnmower for use
• Your lawnmower is supplied with the upper handle
folded over the machine for packing and
transportation.
Handle in Operating Position
1. Lift handle as illustrated in figure A.
• Do not drop the handle.
• Make sure that the cable does not become trapped
between the handles
To Start your Lawnmower
1. Form loop in mains cable and push the loop through
the slot. (B)
3. To secure, position loop over the hook and pull the
cable back through the slot. (C).
4. Connect plug to mains and switch on.
5. To prevent a ring being cut in your lawn and to clear
any residual grass in the collection chute, tilt your
lawnmower slightly.
The switchbox is provided with a lock-off button (D1) to
prevent accidental starting.
5. Press and hold the lock-off button (D1) on the
switchbox, then squeeze one of the Start/Stop levers
towards the upper handle (E).
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button.(F)
7. When the lawnmower has reached full speed gently
lower it onto the lawn.
• NOTE: There are two start/stop levers fitted. Either one
can be used for starting the lawnmower. IMPORTANT:
Do not use the start/stop levers intermittently.
To Stop your Lawnmower
1. To prevent a ring being cut in your lawn and to clear
any residual grass in the collection chute, tilt your
lawnmower slightly.
2. Release the pressure on the Start/Stop lever.