Rear Panel Usb Section - Yamaha MG10XUF Owner's Manual

Controls and Functions
Rear panel
USB section (@8 to #0 )
Caution
The unit may heat up by as much as 15 to 20°C while the
power is on. This is normal. Please note that since the panel
temperature may exceed 50°C in ambient temperatures higher
than 30°C, you should exercise caution to prevent burns.
@8 [AC ADAPTOR IN] connector
For connecting the supplied AC adaptor.
@9 [
/ ] switch
For turning the power of the unit to standby (
( ). The [POWER] LED @1 on the top panel lights when
the switch is set to on ( ).
NOTE
Rapidly switching the unit between on and standby in succes-
sion can cause it to malfunction. After setting the unit to
standby, wait for about six seconds before turning it on again.
NOTICE
Even when the switch is in the standby (
tion, electricity is still flowing to the unit. If you do
Output Destinations and Monitoring Sound
Application
When recording with
DAW software while lis-
tening to the playback
sound from a computer.
When playing back
sound from a computer.
For example: BGM play-
back, Internet broad-
casting
*1 NOTICE: If you set the switch to [TO ST
back.
*2 The audio signal cannot be sent to the computer because it does not pass through the stereo bus.
16
MG10XUF Owner's Manual
) and on
) posi-
Selection of the output destination
sent from channels 9/10
[TO MON /TO
Output destination
ST ] switch
[MONITOR OUT] jack*2
[TO MON ]*1
[PHONES] jack*2
Stero bus 
[TO ST ]
[STEREO OUT] jack
] when you use the DAW software, a loop may be produced, possibly resulting in feed-
not plan to use the unit for a while, be sure to
unplug the AC adaptor from the outlet.
#0 [USB 2.0] terminal
For connecting to a computer via a commercially avail-
able USB 2.0 cable. (This product does not come with a
cable.) The sound of the stereo bus is output to the
computer. (The [STEREO] fader @7 does not affect the
sound.) For inputs and outputs to/from the computer,
you may need a dedicated USB driver. Check and
download the driver at the following Yamaha web site
and install it to the computer before use. The cable
should be no more than 3 meters long.
http://www.yamahaproaudio.com/mg_xu/
 Using the unit connected to a computer
Set the [LINE /USB
to [USB ]. Depending on your particular application,
you can specify the output destination and monitoring
sound by selecting the settings of the [TO MON
] switch !4 for channels 9/10 and the [STEREO
ST
MUTE] switch @4 . For details, see the chart below.
 Adjusting the playback volume from a computer
(Attenuator)
1. Press the [PROGRAM] knob five times consecu-
tively to display the attenuation value (dB).
2. Turn the [PROGRAM] knob to set it between -24 dB
to 0 dB (minus sign is not displayed).
3. Press the [PROGRAM] knob again to exit the set-
ting. When the attenuator is enabled, the dot lights at
the lower right of the display.
Selection of the monitoring sound with the
headphones/monitor speaker
[STEREO MUTE]
switch
The direct sound (of the instrument) input to
the MG10XUF will be muted, allowing you
On ( )
to hear the playback sound only from the
DAW. (Direct monitoring: Off )
You can hear the mixed sound of the direct
instrument sound input to the MG10XUF
Off ( )
and the playback sound from the
DAW.(Direct monitoring : On)
You can hear the mixed sound of the instru-
Normally set to
ment sound input to the MG10XUF and the
Off ( )
playback sound from a computer.
] switch !6 of channels 9/10
/TO
Monitoring sound