Yamaha MG10XU Technical Specifications

MIXING CONSOLE

Technical Specifications

General Specifications

0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω
All level knobs are nominal if not specified.
Frequency Response Input to STEREO OUT
Total Harmonic Distortion
Input to STEREO OUT
(THD+N)
Equivalent Input Noise
Hum&Noise *1
(20 Hz to 20 kHz)
Residual Output Noise
Crosstalk (1 kHz) *2
Input Channels
Ouput Channels
Bus
PAD
HPF
COMP
Input Channel Function
EQ
PEAK LED
Post STEREO LEVEL
Level Meter
Knob
Internal Digital Effect
SPX Algorithm
(MG10XU)
USB Audio (MG10XU) 2 IN / 2 OUT
Phantom Power Voltage
Power Supply Adaptor
Power Consumption
Dimensions (W×H×D)
Net Weight
Included Accessory
Optional Accessory
Operating Temperature
*1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter.
+0.5 dB/-1.0 dB (20 Hz to 48 kHz),
refer to the nominal output level @1 kHz, GAIN knob: Min
0.02 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min
0.003 % @ +24 dBu (1 kHz), GAIN knob: Min
-128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max)
-102 dBu (STEREO OUT, STEREO LEVEL knob: Min)
-83 dB
10 channels: Mono [MIC/LINE]: 4, Stereo [LINE]: 3
STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1
Stereo: 1, AUX (FX): 1
CH1 – CH4 26 dB
CH1 – CH4 80 Hz, 12 dB/oct
1-knob compressor
Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1,
CH1 – CH2
Output level: 0 dB to 7 dB, Attack time: approx. 25 msec,
Release time: approx. 300 msec
CH1 – CH9/10 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
CH1 – CH4 MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking
CH1 – CH9/10 LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving
LED turns on when post EQ signal reaches 3 dB below
CH1 – CH4
clipping (+17 dBu)
2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB]
24 programs
USB Audio Class 2.0 compliant
Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit
+48 V
PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m)
or equivalent recommended by Yamaha
22.9 W
244 mm×71 mm×294 mm (9.6" × 2.8" × 11.6")
MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.)
AC Adaptor, Cubase AI Download Information (MG10XU),
Owner's Manual, Precautions, Technical Specifications (this leaflet)
Mic Stand Adaptor: BMS-10A
0 to +40°C

Analog Input Characteristics

ZJ12600
PAD
Input Jacks
26 dB
OFF
MIC/LINE 1 – 4
ON
LINE 5/6, 7/8
-
LINE 9/10
0 dBu is referenced to 0.775 Vrms.
*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are
maximum position).
*2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold
*3 Tip = Signal, Sleeve = Ground

Analog Output Characteristics

Output Terminals
STEREO OUT [L, R]
MONITOR OUT [L, R]
AUX (FX) SEND
PHONES
0 dBu is referenced to 0.775 Vrms.
*1 1 = Ground, 2 = Hot, 3 = Cold
*2 Tip = Hot, Ring = Cold, Sleeve = Ground
Digital Input / Output Characteristics
Output Terminals
USB
*1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit
European Models
Inrush Current based on EN 55103-1:2009
1 A (on initial switch-on)
1 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Specifications and descriptions in this document are for informational purposes only. Yamaha Corporation reserves the right to modify products or specifications at
any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer.
GAIN Actual For Use
Trim Load With
Sensitivity *1
Position Impedance Nominal
-72 dBu
+64 dB
(0.195 mV)
-28 dBu
+20 dB
(30.9 mV)
50-600 Ω
3 kΩ
Mics/Lines
-46 dBu
+38 dB
(3.884 mV)
-2 dBu
-6 dB
(615.6 mV)
-22 dBu
- 10 kΩ 600 Ω Lines
(61.56 mV)
Output level
Actual Source For Use With
Impedance Nominal
Nominal
+4 dBu
75 Ω 600 Ω Lines
(1.228 V)
+4 dBu
150 Ω 10 kΩ Lines
(1.228 V)
110 Ω 40 Ω Lines 3 mW + 3 mW
Format Data Length*1
44.1 kHz, 48 kHz, 88.2 kHz,
USB Audio Class 2.0 16 /24 bit
96 kHz, 176.4 kHz, 192 kHz
See reverse side for block/level diagrams and dimensions.
Input level
Connector
Max. before
Nominal
clip
-60 dBu -40 dBu
(0.775 mV) (7.75 mV)
-16 dBu +4 dBu
(122.8 mV) (1.228 mV)
Combo jack*2
(Balanced)
-34 dBu -14 dBu
(15.46 mV) (154.6 mV)
+10 dBu +30 dBu
(2.451 V) (24.51 V)
Phone jack *3
RCA Pin
-10 dBu +10 dBu
(Unbalanced)
(245.1 mV) (2.451 V)
Phone jack *3
(Unbalanced)
Connector
Max. before clip
XLR-3-32 *1
+24 dBu
Phone jack *2
(12.28 V)
(Balanced)
+20 dBu Phone jack *2
(7.750 V) (Impedance Balanced)
100 mW + 100 mW Stereo phone jack
Fs Connector
USB Standard-B