Sony CDX-M610 Service Manual
Sony CDX-M610 Service Manual

Sony CDX-M610 Service Manual

Fm/mw/lw compact disc player

Advertisement

QQ
3 7 63 1515 0
SERVICE MANUAL
Ver 1.0 2001. 02
• The tuner and CD sections have no adjustments.
CD player section
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
TE
L 13942296513
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 108.0 MHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
MW/LW
Tuning range
MW : 531 – 1,602 kHz
LW : 153 – 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW : 30 µV
LW : 40 µV
www
.
Sony Corporation
9-870-261-31
2001B0400-1
Audio Entertainment Group
© 2001. 2
General Engineering Dept.
http://www.xiaoyu163.com
SPECIFICATIONS
x
ao
y
i
http://www.xiaoyu163.com
CDX-M610
8
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
Power amplifier section
Outputs
Q Q
Speaker impedance
3
6 7
1 3
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Tone controls
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
*1 Equipped with front and rear outputs
Design and specifications are subject to change without
notice.
FM/MW/LW COMPACT DISC PLAYER
u163
.
2 9
9 4
2 8
AEP Model
Speaker outputs
4 – 8 ohms
1 5
0 5
8
2 9
9 4
Audio outputs
*1
Power aerial relay
control lead
Power amplifier control
lead
Telephone ATT control
lead
Illumination control lead
Bass ± 9 dB at 100 Hz
Treble ± 9 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 182 mm
(w/h/d)
Approx. 182 × 53 × 163 mm
(w/h/d)
Approx. 1.5 kg
Card remote commander
RM-X93
Parts for installation and
connections (1 set)
m
co
9 9
UK Model
CDX-M600R
MG-383Z-121//K
KSS-720A
2 8
9 9
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony CDX-M610

  • Page 1 CDX-M610 3 7 63 1515 0 SERVICE MANUAL AEP Model UK Model Ver 1.0 2001. 02 • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-M600R CD Drive Mechanism Type MG-383Z-121//K SPECIFICATIONS Optical Pick-up Name...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3 http://www.xiaoyu163.com 3 7 63 1515 0 MODEL IDENTIFICATION There are two types of main board in according destination. – MAIN board (side A) – magnify magnify magnify L 13942296513 TYPE B TYPE A Indicated R818 R854 R849 R853 language English, Spanish, ×...
  • Page 4 CDX-M610 3 7 63 1515 0 TABLE OF CONTENTS 1. GENERAL 4. DIAGRAMS ................5 4-1. IC Pin Descriptions ............26 2. DISASSEMBLY 4-2. Block Diagram –CD Section– ........... 34 4-3. Block Diagram –Tuner Section– ........35 2-1. Front Panel Assy (Normal) ..........16 4-4.
  • Page 5: General

    CDX-M610 SECTION 1 GENERAL 3 7 63 1515 0 This section is extracted from instruction manual. L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 6 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 7 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 8 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 9 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 10 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 11 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 12 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 13 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 14 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 15 CDX-M610 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 16: Front Panel Assy (Normal)

    CDX-M610 SECTION 2 DISASSEMBLY 3 7 63 1515 0 Note : This set can be disassemble according to the following sequence. Front Panel Assy (Normal) CD Mechanism Block, Front Panel Assy Front Panel Assy (Inoperative) Sub Panel (CD) Sub Assy...
  • Page 17: Front Panel Assy (Inoperative)

    CDX-M610 3 7 63 1515 0 2-2. FRONT PANEL ASSY (INOPERATIVE) 0 Lift the motor block assy slightly to make a play. 7 PTT 2.6x6 8 PTT 2.6x6 5 PTT 2.6x6 6 PTT 2.6x6 3 screw (panel) 4 spacer (arm) 9 Lift the cam (R) assy slightly to make a play.
  • Page 18: Sub Panel (Cd) Sub Assy

    CDX-M610 3 7 63 1515 0 2-4. SUB PANEL (CD) SUB ASSY 1 CNP805 4 claw 3 PTT 2.6x6 5 claw 2 PTT 2.6 x6 6 sub panel (CD) sub assy L 13942296513 2-5. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder.
  • Page 19: Main Board

    CDX-M610 3 7 63 1515 0 2-6. MAIN BOARD 4 PTT 2.6x6 6 MAIN board ground point 5 PTT 2.6x6 ground point 3 PTT 2.6x8 2 PTT 2.6x8 1 PTT 2.6x8 L 13942296513 2-7. HEAT SINK 5 heat sink 4 PTT 2.6x8...
  • Page 20: Chassis (T) Sub Assy

    CDX-M610 3 7 63 1515 0 2-8. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires. black white L 13942296513 2-9. LEVER SECTION 5 guide (disc) 6 lever (R)
  • Page 21: Servo Board

    CDX-M610 3 7 63 1515 0 2-10. SERVO BOARD 7 special screws 6 special screws 2 CN2 3 Removal the solders. 1 CN3 4 P 2x3 8 SERVO board 5 loading motor assy L 13942296513 2-11. SHAFT ROLLER ASSY •...
  • Page 22: Floating Block Assy

    CDX-M610 3 7 63 1515 0 2-12. FLOATING BLOCK ASSY 6 floating block assy 7 compression spring (FL) 1 tension spring (KF1) 8 compression spring (FL) 4 Fit lever (D) in the direction of the arrow. 5 Turn loading ring in the direction of the arrow.
  • Page 23: Arm (A-L) Assy, Arm (B-L) Assy

    CDX-M610 SECTION 3 PHASE ALIGNMENT 3 7 63 1515 0 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 4 arm (A-L) assy 5 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-L) assy 3 spring (arm L)
  • Page 24: Motor Block

    CDX-M610 3 7 63 1515 0 3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SWITCH board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board...
  • Page 25: Arm (A-R) Assy, Arm (B-R) Assy

    CDX-M610 3 7 63 1515 0 3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 5 stop ring 1.5, type-E 4 arm (A-R) assy 2 stop ring 1.5, type-E 3 spring (arm R) 1 arm (B-R) assy bracket (R) assy L 13942296513 3-6.
  • Page 26: Ic Pin Descriptions

    CDX-M610 SECTION 4 DIAGRAMS 3 7 63 1515 0 4-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description DVDD — Digital power supply pin DVSS — Digital ground SOUT Servo brock serial data output (Not used.)
  • Page 27 CDX-M610 3 7 63 1515 0 Pin No. Pin Name Pin Description Tracking error signal input Center servo analog input RFDC RF signal input ADIO Test pin (Not used.) AVSSO — Analog ground IGEN Constant current input from OP amplifier.
  • Page 28 CDX-M610 3 7 63 1515 0 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description ITRPT — Not used in this set. 2, 3 — — Not used in this set. 4, 5 —...
  • Page 29 CDX-M610 3 7 63 1515 0 Pin No. Pin Name Pin Description SENS SENS signal input — — Not used in this set. — — Not used in this set. BU.IN Back-up power detection input BUSON Bus on control input...
  • Page 30 CDX-M610 3 7 63 1515 0 • IC301 HD6432355A26F (DISPLAY CONTROL) Pin No. Pin Name Pin Description 1, 2 PG3, 4 Not used. (Open) — Ground — Not used. (Open) — Power supply pin (+5 V) 6 – 9 PC0 –...
  • Page 31 Not used. (Open) — Power supply pin (+5 V) 90 – 96 PF6 – 0 Not used. (Open) UNI-SO SONY BUS serial data output UNI-SI SONY BUS serial data input 99, 100 — Ground UNI-SCK SONY BUS serial clock input Not used.
  • Page 32 SP LATCH Spectrum analyzer display data latch signal output to display micon. System attenuate control output SYSRST Resetting for slave micon of SONY BUS system. (N/R) Forward/Reverse select output (“L”: forward, “H”: reverse) (Not used in this set.) — Power supply pin (+5 V) (NCO) Not used.
  • Page 33 CDX-M610 3 7 6 3 1 5 1 5 0 Pin No. Pin Name Pin Description Pin No. Pin Name Pin Description — Power supply pin (+5 V) 4V SEL 4 V select input (Not used in this set.)
  • Page 34: Block Diagram –Cd Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-2. BLOCK DIAGRAM — CD SECTION — TUNER RF AMP, LD APC, DIGITAL SERVO, SECTION OPTICAL PICK-UP CD SYSTEM CONTROL SYSTEM CONTROL ERROR AMP DIGITAL SIGNAL PROCESSOR (Page 35)
  • Page 35: Block Diagram –Tuner Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 (Page 36) –1 DISPLAY BUS AUDIO IN SECTION –2 IC409 R-CH ELECTRONIC VOLUME (Page 34) AOUT IC401 –5 FD1L OUT FL...
  • Page 36: Block Diagram –Display Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-4. BLOCK DIAGRAM — DISPLAY SECTION — DISPLAY CONTROL IC301 BUS SI UNI SI UNI SO UNI SO SIGNAL IND,DET SYSTEM CONTROL (Page 35) IC407 BUS CLK UNI SCK...
  • Page 37: Circuit Boards Location

    CDX-M610 3 7 6 3 1 5 1 5 0 • Waveforms (Servo Section) 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING (MODE:CD PLAY) BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
  • Page 38: Printed Wiring Boards –Cd Mechanism Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
  • Page 39 CDX-M610 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC501 Q101 (Page 43) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
  • Page 40: Schematic Diagram –Cd Mechanism Section (1/2)

    CDX-M610 3 7 6 3 1 5 1 5 0 • Refer to page 37 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 52 for IC Block Diagrams. IC B/D (Page 41)
  • Page 41: Schematic Diagram –Cd Mechanism Section (2/2)

    CDX-M610 3 7 6 3 1 5 1 5 0 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 52 for IC Block Diagrams. (Page 40) IC B/D (Page 40) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 42: Printed Wiring Boards –Main Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Semiconductor Location Ref. No. Location Ref. No. Location D301 IC601 F-13 (D302) J-11 IC602 G-13 D303 IC801 D304 IC802 D401...
  • Page 43 CDX-M610 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 (Page 39) (Page 48) http://www.xiaoyu163.com...
  • Page 44: Schematic Diagram –Main Section (1/4)

    CDX-M610 3 7 6 3 1 5 1 5 0 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 52 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 45: Schematic Diagram –Main Section (2/4)

    CDX-M610 3 7 6 3 1 5 1 5 0 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 52 for IC Block Diagrams. IC B/D 1 3 9 4 2 2 9 6 5 1 3...
  • Page 46: Schematic Diagram –Main Section (3/4)

    CDX-M610 • Refer to page 49 for Waveforms. 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 52 for IC Block Diagrams. 3 7 6 3 1 5 1 5 0 (Page 44) (Page 45) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 47: Schematic Diagram –Main Section (4/4)

    CDX-M610 3 7 6 3 1 5 1 5 0 • Refer to page 49 for Waveforms. 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 52 for IC Block Diagrams. (Page 44) (Page 45) (Page 49)
  • Page 48: Printed Wiring Board –Sub Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-14. PRINTED WIRING BOARD — SUB SECTION — (Page 43) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
  • Page 49: Schematic Diagram –Sub Section

    CDX-M610 3 7 6 3 1 5 1 5 0 • Waveforms (Main Section) 4-15. SCHEMATIC DIAGRAM — SUB SECTION — (MODE:CD PLAY) 2.5Vp-p 32kHz (XOA) IC801 2.5Vp-p 3.88MHz (XO) IC801 1.8Vp-p 18.43MHz (EXTAL) IC301 (Page 47) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 50: Printed Wiring Board –Display Section

    CDX-M610 4-16. PRINTED WIRING BOARD — DISPLAY SECTION — 3 7 6 3 1 5 1 5 0 (Page 42) 1 3 9 4 2 2 9 6 5 1 3 • Semiconductor Location Ref. No. Location Ref. No.
  • Page 51: Schematic Diagram –Display Section

    CDX-M610 3 7 6 3 1 5 1 5 0 4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION — (Page 47) 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
  • Page 52 CDX-M610 3 7 6 3 1 5 1 5 0 • IC Block Diagrams IC1 CXA2596M-T6 IC7 LA6556L-TE-L IC802 BA8270F-E2 IC307 BA6288FS-E2 BUS ON APC PD AMP BUS ON SWITCH DRIVER DRIVER HOLD S-GND – OUT1 OUT2 INPUT RESET...
  • Page 53 CDX-M610 3 7 63 1515 0 IC401 TDA7402TR 24 23 33 32 31 MIXER MONO- MONO- MONO- MONO- MONO- MONO- FADER FADER FADER FADER FADER FADER ACINLF FRONT SUBWOOFER SWINR ACIN +PHASE OUTPUT SWINL REAR CONTROL SELECTOR ACOUTR MAIN...
  • Page 54: Chassis Section

    CDX-M610 SECTION 5 EXPLODED VIEWS 3 7 63 1515 0 NOTE: • The mechanical parts with no reference • Accessories and packing materials and The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied.
  • Page 55: Main Board Section

    CDX-M610 3 7 63 1515 0 5-2. MAIN BOARD SECTION M601 TU601 F901 L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 51 X-3380-358-1 CHASSIS (CD) ASSY A-3283-185-A MAIN BOARD, COMPLETE (TYPE A)
  • Page 56: Front Panel Section

    CDX-M610 3 7 63 1515 0 5-3. FRONT PANEL SECTION LCD901 LCD902 not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-045-726-01 BUTTON (SOURCE) * 117 3-045-708-01 SHEET (SUB), DIFFUSION 3-045-725-01 BUTTON (+/–)
  • Page 57: Cd Mechanism Section (1)

    CDX-M610 3 7 63 1515 0 5-4. CD MECHANISM SECTION (1) (MG-383Z-121//K) L 13942296513 M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 1-676-709-11 DISC IN SW BOARD 3-040-040-01 ARM (ROLLER) 3-040-039-01 CHASSIS (T)
  • Page 58: Cd Mechanism Section (2)

    CDX-M610 3 7 63 1515 0 5-5. CD MECHANISM SECTION (2) (MG-383Z-121//K) L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-025-01 ARM, CHUCKING A-3307-422-A CHASSIS (M) COMPLETE ASSY 3-040-031-01 DAMPER (T) 3-040-059-01 SPRING (TR), TENSION...
  • Page 59: Cd Mechanism Section (3)

    CDX-M610 3 7 63 1515 0 5-6. CD MECHANISM SECTION (3) (MG-383Z-121//K) M901 M902 L 13942296513 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No.
  • Page 60: Electrical Parts List

    3-045-702-01 BRACKET (LCD) (MAIN) 3-045-703-02 PLATE (LCD) (MAIN), LIGHT GUIDE < DIODE > 3-045-704-01 SHEET (MAIN), DIFFUSION LED901 8-719-079-49 LED NSSW450-BRS-TVR (SONY) 3-045-705-03 SHEET (MAIN), REFLECTION LED903 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) 3-045-706-01 BRACKET (LCD) (SUB) LED904 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT)
  • Page 61 CDX-M610 DISPLAY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW911 1-771-883-11 SWITCH, TACTILE (WITH LED) (CLOSE) R930 1-216-829-11 METAL CHIP 4.7K 1/16W LSW912 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (OPEN)
  • Page 62 CDX-M610 LIMIT SW MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-676-708-11 LIMIT SW BOARD C378 1-162-964-11 CERAMIC CHIP 0.001uF C379 1-164-156-11 CERAMIC CHIP 0.1uF *************** C380 1-162-974-11 CERAMIC CHIP 0.01uF...
  • Page 63 CDX-M610 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C637 1-164-227-11 CERAMIC CHIP 0.022uF C921 1-110-654-11 DOUBLE LAYERS 0.047F 5.5V C638 1-110-563-11 CERAMIC CHIP 0.068uF C922 1-128-057-11 ELECT 330uF 6.3V...
  • Page 64 CDX-M610 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D908 8-719-056-93 DIODE UDZ-TE-17-18B JR905 1-216-295-11 SHORT D909 8-719-988-61 DIODE 1SS355TE-17 JR906 1-216-295-11 SHORT D910 8-719-978-33 DIODE UDZSTE-176.8B JR908 1-216-295-11 SHORT...
  • Page 65 CDX-M610 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q913 8-729-038-55 TRANSISTOR KRA103S R385 1-216-845-11 METAL CHIP 100K 1/16W Q914 8-729-019-00 TRANSISTOR 2SD2394-G R401 1-216-825-11 METAL CHIP 2.2K 1/16W...
  • Page 66 CDX-M610 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R631 1-216-825-11 METAL CHIP 2.2K 1/16W R856 1-216-815-11 METAL CHIP 1/16W R801 1-216-845-11 METAL CHIP 100K 1/16W R857 1-216-845-11 METAL CHIP...
  • Page 67 CDX-M610 SERVO MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R949 1-216-057-00 METAL CHIP 2.2K 1/10W C504 1-162-967-11 CERAMIC CHIP 0.0033uF 10% R950 1-216-057-00 METAL CHIP 2.2K 1/10W C505 1-165-176-11 CERAMIC CHIP 0.047uF...
  • Page 68 CDX-M610 SERVO 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R104 1-216-857-11 METAL CHIP 1/16W R531 1-216-809-11 METAL CHIP 1/16W R105 1-216-833-11 METAL CHIP 1/16W R532 1-216-845-11 METAL CHIP 100K...
  • Page 69 CDX-M610 SWITCH 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > ************** HARDWARE LIST Q501 8-729-216-22 TRANSISTOR 2SA1037K-T-146-S ************** Q502 8-729-038-68 TRANSISTOR KRC103S 7-685-790-09 SCREW +PTT 2.6X4 (S) <...
  • Page 70 CDX-M610 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Table of Contents