1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. CDX-M600 - Fm/am Compact Disc Player
  6. Service manual

Sony CDX-M600 Service Manual

Fm/am compact disc player
Hide thumbs Also See for CDX-M600:
Table of Contents

Advertisement

Quick Links

See also: Operating and Installation Instruction
CDX-M600/M600R/M650
SERVICE MANUAL
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (CDX-M600/M650)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 1% total harmonic distortion.
Other Specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties (CDX-M600/M650)
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block.
Tuner section
FM
Tuning range
87.5 – 107.9 MHz (CDX-M600R)
87.5 – 108.0 MHz (CDX-M600/M650)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (CDX-M600/M650)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Photo: CDX-M600
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
MW/LW (CDX-M600R)
Tuning range
Aerial terminal
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
Power amplifier section
Outputs
Speaker impedance
Maximum power output 50 W × 4 (at 4 ohms)
General
Outputs
Inputs
Power requirements
FM/AM COMPACT DISC PLAYER
FM/MW/LW COMPACT DISC PLAYER
US Model
CDX-M600/M650
AEP Model
UK Model
NEW
MG-383Z-121//K
KSS-720A
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External aerial connector
MW: 30 µV
LW: 40 µV
Speaker outputs
4 – 8 ohms
Audio outputs (3) (CDX-M600/M650)
Audio outputs (2) (CDX-M600R)
Power antenna relay
control lead (CDX-M600/M650)
Power aerial relay
control lead (CDX-M600R)
Power amplifier control
lead
Telephone ATT control
lead
Illumination control lead
12 V DC car battery
(negative ground)
– Continued on next page –
CDX-M600/M650
CDX-M600R
CDX-M600R
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-M600

Summary of Contents for Sony CDX-M600

  • Page 1 Illumination control lead Tuning range 87.5 – 107.9 MHz (CDX-M600R) Power requirements 12 V DC car battery 87.5 – 108.0 MHz (CDX-M600/M650) (negative ground) Antenna terminal External antenna connector – Continued on next page – Intermediate frequency 10.7 MHz/450 kHz...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS 1. GENERAL 4. DIAGRAMS Location of controls ..............4 4-1. IC Pin Descriptions ............31 Getting Started ................. 5 4-2. Block Diagram –CD Section– ........... 40 Setting the clock ..............5 4-3. Block Diagram –Tuner Section– ........41 CD Player CD/MD Unit ............

  • Page 4: General

    SECTION 1 GENERAL This section is extracted from instruction manual. CDX-M600R CDX-M600/M650...

  • Page 7: Radio

    CDX-M600R...
  • Page 8 CDX-M600/M650...

  • Page 9: Rds

    CDX-M600R...

  • Page 10: Dab

    CDX-M600R...

  • Page 13: Tv/Video

    CDX-M600/M650...

  • Page 14: Connections

    CDX-M600R...
  • Page 18 CDX-M600/M650...

  • Page 21: Disassembly

    SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. FRONT PANEL ASSY (NORMAL) 1 Turn on the power and open the front panel. 4 screw (panel) 5 spacer (arm) stand 3 spacer (arm) 6 front panel assy 2 screw (panel) (Take care not to flexible board...

  • Page 22: Cd Mechanism Block, Flexible Board

    2-3. CD MECHANISM BLOCK, FLEXIBLE BOARD 7 bracket (CD) 5 CD mechanism block 6 PTT 2.6x6 8 cover (flexible) 0 flexible board 3 PTT 2.6x4 9 CNP802 Note: When installing the flexible board, make the board slack as illustrated. 2 PTT 2.6x4 1 PTT 2.6x6 4 CNP701 2-4.

  • Page 23: Motor Block Assy, Cam (R) Assy

    2-5. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 28 and 30. 1 PTT 2.6x6 Note: Install the cam (R) assy with 4 PTT 2.6x6 the cam fully rotated in the direction of the arrow A.

  • Page 24: Heat Sink

    2-7. HEAT SINK 5 heat sink 4 PTT 2.6x8 3 PTT 2.6x8 2 PTT 2.6x12 1 PTT 2.6x8 2-8. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires. black white...

  • Page 25: Lever Section

    2-9. LEVER SECTION 5 guide (disc) 6 lever (R) 3 tension spring (LR) 7 lever (L) 1 special screw 2 DISC IN SW board 4 claws 2-10. SERVO BOARD 7 PS 2x4 6 PS 2x4 2 CN2 3 Removal the solders. 1 CN3 4 P 2x3 8 SERVO board...

  • Page 26: Shaft Roller Assy

    2-11. SHAFT ROLLER ASSY • When installing, take note of the positions arm (roller) and washers. (Fig. 1) 3 retaing ring (RA) shaft retainer washer washer 4 shaft retainer shaft retainer retaing ring (RA) Fig. 1 5 shaft roller assy 2 arm (roller) 1 tension spring (RA) 2-12.

  • Page 27: Optical Pick-Up Block

    2-13. OPTICAL PICK-UP BLOCK 1 P 2x3 2 sled motor assy 3 optical pick-up block...

  • Page 28: Phase Alignment

    SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 4 arm (A-L) assy 5 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-L) assy 3 spring (arm L) bracket (L) assy 3-2. CAM (L) 1 Move the arm (B-L) assy in the direction of the arrow A and the arm (A-L) assy in the direction of 3 stop ring 1.5, type-E the arrow B fully (full open state).

  • Page 29: Motor Block

    3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SWITCH board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board 5 B 2.6x4 SW900 cam (L) 3-4.

  • Page 30: Arm (A-R) Assy, Arm (B-R) Assy

    3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 5 stop ring 1.5, type-E 4 arm (A-R) assy 2 stop ring 1.5, type-E 3 spring (arm R) 1 arm (B-R) assy bracket (R) assy 3-6. CAM (R) 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state).

  • Page 31: Diagrams

    SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description DVDD — Digital power supply pin DVSS — Digital ground SOUT Servo brock serial data output (Not used.) SOCK Servo brock serial data read clock output (Not used.) XOLT...
  • Page 32 Pin No. Pin Name Pin Description Tracking error signal input Center servo analog input RFDC RF signal input ADIO Test pin (Not used.) AVSSO — Analog ground IGEN Constant current input from OP amplifier. AVDDO — Analog ground ASYO EFM full-swing output (“L”: VSS, “H”: VDD) ASYI Asymmetry comparate voltage input RFAC...
  • Page 33 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description ITRPT — Not used in this set. 2, 3 — — Not used in this set. 4, 5 — Not used in this set. OPEN Front panel open detection input CLOSE Front panel close control output LINKOFF...
  • Page 34 Pin No. Pin Name Pin Description SENS SENS signal input — — Not used in this set. — — Not used in this set. BU.IN Back-up power detection input BUSON Bus on control input IN SW Disc in switch input (SW3) SELF SW Self switch input (SW2) SCOR...
  • Page 35 • IC301 HD6432355A22F (DISPLAY CONTROL) Pin No. Pin Name Pin Description 1, 2 PG3, 4 Not used. (Open) — Ground — Not used. (Open) — Power supply pin (+5 V) 6 – 9 PC0 – 3 Not used. (Open) — Ground 11 –...
  • Page 36 Not used. (Open) — Power supply pin (+5 V) 90 – 96 PF6 – 0 Not used. (Open) UNI-SO SONY BUS serial data output UNI-SI SONY BUS serial data input 99, 100 — Ground UNI-SCK SONY BUS serial clock input Not used.
  • Page 37 SP LATCH Spectrum analyzer display data latch signal output to display micon. System attenuate control output SYSRST Resetting for slave micon of SONY BUS system. (N/R) Forward/Reverse select output (“L”: forward, “H”: reverse) (Not used in this set.) — Power supply pin (+5 V) (NCO) Not used.
  • Page 38 Pin No. Pin Name Pin Description — Power supply pin (+5 V) ST-BY Power amplifier drive output NS MASK Noise detection output (REEL) Tape rotation detection input (Fixed at “L” in this set.) CD EJECTOK CD eject control output (Not used in this set.) CD OPENREQ Front panel open request input 60 –...
  • Page 39 Pin No. Pin Name Pin Description 4V SEL 4 V select input (Fixed at “L” (CDX-M650) or “H” (CDX-M600/M600R) in this set.) (P-SEL) Power select initial setting (Fixed at “L” in this set.) TUNON Tuner power control output 115, 116...

  • Page 40: Block Diagram -Cd Section

    CDX-M600/M600R/M650 4-2. BLOCK DIAGRAM — CD SECTION — TO TUNER RF AMP, LD APC, DIGITAL SERVO, SECTION CD SYSTEM CONTROL SYSTEM CONTROL OPTICAL PICK-UP ERROR AMP DIGITAL SIGNAL PROCESSOR (Page 41) IC801 (1/3) KSS-720A IC501 • Signal path A MUT 19...

  • Page 41: Block Diagram -Tuner Section

    CDX-M600/M600R/M650 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 (Page 42) –1 DISPLAY BUS AUDIO IN SECTION –2 IC409(1/2) (M650) R-CH ELECTRONIC VOLUME (Page 40) AOUT IC401 IC402 –5 SECTION FD1L OUT FL LINE OUT Q202 FRONT –6 R-CH Q401...

  • Page 42: Block Diagram -Display Section

    CDX-M600/M600R/M650 4-4. BLOCK DIAGRAM — DISPLAY SECTION — DISPLAY CONTROL IC301 TUNER BUS SI UNI SI AOUT SECTION UNI SO UNI SO SIGNAL IND,DET (Page 41) SYSTEM CONTROL IC407 UNI SCK IC801 (3/3) BUS CLK BUS ON BUS ON AOUT...

  • Page 43: Circuit Boards Location

    • Waveforms (MODE:PLAY) 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF Approx.

  • Page 44: Printed Wiring Boards -Cd Mechanism Section

    CDX-M600/M600R/M650 4-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION —...
  • Page 45 CDX-M600/M600R/M650 • Semiconductor Location Ref. No. Location IC501 Q101 (Page 49)

  • Page 46: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-M600/M600R/M650 • Refer to page 43 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 58 for IC Block Diagrams. Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions.

  • Page 47: Schematic Diagram -Cd Mechanism Section (2/2)

    CDX-M600/M600R/M650 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 58 for IC Block Diagrams. (Page 46) Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY ∗...

  • Page 48: Printed Wiring Boards -Main Section

    CDX-M600/M600R/M650 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Semiconductor Location Ref. No. Location Ref. No. Location D301 IC301 I-12 (D302) J-11 IC303 J-13 D303 IC306 D304 IC307 D401 (IC308) (D402) IC401 E-11 (D403) IC402 C-10 (D405) IC403 C-11...
  • Page 49 CDX-M600/M600R/M650 (Page 45) (Page 54)

  • Page 50: Schematic Diagram -Main Section (1/4)

    CDX-M600/M600R/M650 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 58 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM < > : CD PLAY...

  • Page 51: Schematic Diagram -Main Section (2/4)

    CDX-M600/M600R/M650 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 58 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ) : AM/MW (Page 52)

  • Page 52: Schematic Diagram -Main Section (3/4)

    CDX-M600/M600R/M650 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 58 for IC Block Diagrams. (Page 50) (Page 51) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 53: Schematic Diagram -Main Section (4/4)

    CDX-M600/M600R/M650 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 58 for IC Block Diagrams. (Page 50) (Page 51) (Page 55) (Page 57) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 54: Printed Wiring Board -Sub Section

    CDX-M600/M600R/M650 4-14. PRINTED WIRING BOARD — SUB SECTION — (Page 49)

  • Page 55: Schematic Diagram -Sub Section

    CDX-M600/M600R/M650 4-15. SCHEMATIC DIAGRAM — SUB SECTION — (Page 53) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM...

  • Page 56: Printed Wiring Board -Display Section

    CDX-M600/M600R/M650 4-16. PRINTED WIRING BOARD — DISPLAY SECTION — (Page 48) • Semiconductor Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location (D902) B-12 IC902 LED912 B-13 Q901 (D903) C-11 IC903 LED913 Q902 (D904) C-11 LED914...

  • Page 57: Schematic Diagram -Display Section

    CDX-M600/M600R/M650 4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION —...
  • Page 58 IC402, 403 NJM2160AM-TE2 IC802 BA8270F-E2 • IC Block Diagrams IC1 CXA2596M IC7 LA6556L BUS ON VCCL BUS ON SWITCH BUFFER VCCL APC PD AMP RESET HOLD SWITCH S-GND – SVRL CL– BUS ON LIFT INPUT CLK IN BUFFER BATTERY BATT BU IN CH2-CH4 OUTPUT –...
  • Page 59 IC401 TDA7402TR 33 32 31 24 23 MIXER MONO- MONO- MONO- MONO- MONO- MONO- FADER FADER FADER FADER FADER FADER ACINLF FRONT SUBWOOFER SWINR ACIN +PHASE OUTPUT SWINL REAR CONTROL SELECTOR ACOUTR MAIN ACOUTL SECOND CREF VOICE BANDPASS BASS SUPPLY TREBLE HIGH-CUT VOLUME...

  • Page 60: Exploded Views

    SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Accessories and packing materials and The components identified by number in the exploded views are not supplied. mark 0 or dotted line with mark hardware (# mark) list are given in •...

  • Page 61: Front Panel Section

    5-2. FRONT PANEL SECTION LCD901 LCD902 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-045-726-01 BUTTON (SOURCE) * 64 3-045-706-01 BRACKET (LCD) (SUB) 3-045-725-01 BUTTON (+/–) 1-694-687-11 CONDUCTIVE BOARD, CONNECTION 3-045-727-01 PLATE (RING), LIGHT GUIDE 1-694-686-11 CONDUCTIVE BOARD, CONNECTION 3-045-730-01 BUTTON (SEEK) (DSO) (M600/M600R) * 67...

  • Page 62: Cd Mechanism Section (1)

    5-3. CD MECHANISM SECTION (1) (MG-383Z-121//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 1-676-709-11 DISC IN SW BOARD 3-040-040-01 ARM (ROLLER) 3-040-039-01 CHASSIS (T) * 111 A-3294-809-A SERVO BOARD, COMPLETE 3-040-038-01 SPRING (LR), TENSION * 112 3-040-048-01 BRACKET (MOTOR) 3-040-050-01 LEVER (L)

  • Page 63: Cd Mechanism Section (2)

    5-4. CD MECHANISM SECTION (2) (MG-383Z-121//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-025-01 ARM, CHUCKING A-3307-422-A CHASSIS (M) COMPLETE ASSY 3-040-031-01 DAMPER (T) 3-040-059-01 SPRING (TR), TENSION 3-040-056-01 LEVER (D) 3-040-057-01 LEVER (LOCK) 3-040-024-01 RETAINER (DISC) 3-040-058-01 GEAR (MDL) 3-040-053-01 RING, LOADING 3-040-052-01 WHEEL (U), WORM...

  • Page 64: Cd Mechanism Section (3)

    5-5. CD MECHANISM SECTION (3) (MG-383Z-121//K) M901 M902 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 201...

  • Page 65: Electrical Parts List

    3-045-703-01 PLATE (LCD) (MAIN), LIGHT GUIDE < DIODE > 3-045-704-01 SHEET (MAIN), DIFFUSION 3-045-705-01 SHEET (MAIN), REFLECTION LED901 8-719-079-49 LED NSSW450-BRS-TVR (SONY) 3-045-706-01 BRACKET (LCD) (SUB) LED903 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) 3-045-707-01 PLATE (LCD) SUB, LIGHT GUIDE LED904 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT)
  • Page 66 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW907 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (LIST) R924 1-219-286-11 RES-CHIP 1/16W LSW908 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (> M) R926 1-216-829-11 METAL CHIP 4.7K 1/16W LSW909 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (ENTER) R927 1-216-833-11 RES-CHIP...
  • Page 67 DISPLAY LIMIT SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R991 1-216-025-11 RES-CHIP 1/10W C337 1-163-038-00 CERAMIC CHIP 0.1uF (M600/M650) C338 1-163-038-00 CERAMIC CHIP 0.1uF R992 1-216-025-11 RES-CHIP 1/10W C339 1-163-038-00 CERAMIC CHIP 0.1uF (M650) C340 1-163-038-00 CERAMIC CHIP...
  • Page 68 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C456 1-124-261-00 ELECT 10uF C626 1-162-915-11 CERAMIC CHIP 10PF 0.5PF (M600/M650) (M600R) C457 1-164-156-11 CERAMIC CHIP 0.1uF C628 1-163-038-00 CERAMIC CHIP 0.1uF (M600/M650) C632 1-163-038-00 CERAMIC CHIP 0.1uF C461 1-163-009-11 CERAMIC CHIP...
  • Page 69 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C916 1-124-489-11 ELECT 150uF D414 1-216-295-00 SHORT C917 1-163-038-00 CERAMIC CHIP 0.1uF D415 8-719-988-61 DIODE 1SS355TE-17 C918 1-163-038-00 CERAMIC CHIP 0.1uF D416 8-719-988-61 DIODE 1SS355TE-17 C919 1-163-038-00 CERAMIC CHIP 0.1uF D502 8-719-988-61 DIODE 1SS355TE-17...
  • Page 70 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D921 8-719-914-44 DIODE DAP202K-T-146 JR815 1-216-295-00 SHORT D922 8-719-988-61 DIODE 1SS355TE-17 JR901 1-216-295-00 SHORT D923 8-719-988-61 DIODE 1SS355TE-17 JR902 1-216-295-00 SHORT D924 8-719-914-43 DIODE DAN202K-T-146 JR904 1-216-295-00 SHORT JR905 1-216-296-00 SHORT <...
  • Page 71 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q607 8-729-120-28 TRANSISTOR 2SC2412K-T-146-R (M600R) R206 1-216-077-00 METAL CHIP 1/10W Q801 8-729-038-55 TRANSISTOR KRA103S (M600/M600R) Q803 8-729-038-67 TRANSISTOR KRC102S R206 1-216-295-00 SHORT (M650) Q804 8-729-038-55 TRANSISTOR KRA103S R209 1-216-089-00 METAL CHIP 1/10W...
  • Page 72 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R417 1-216-082-00 RES-CHIP 1/10W R608 1-216-797-11 METAL CHIP 1/16W (M650) (M600R) R419 1-216-086-00 RES-CHIP 1/10W R609 1-216-295-00 SHORT (M600R) (M650) R610 1-216-057-00 METAL CHIP 2.2K 1/10W R420 1-216-082-00 RES-CHIP 1/10W R611...
  • Page 73 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R818 1-216-864-11 METAL CHIP 1/16W R904 1-216-841-11 METAL CHIP 1/16W (M600/M600R:TYPE1/M650) R905 1-216-089-11 RES-CHIP 1/10W R819 1-216-809-11 METAL CHIP 1/16W R906 1-216-841-11 METAL CHIP 1/16W R820 1-216-809-11 METAL CHIP 1/16W R907 1-216-089-11 RES-CHIP...
  • Page 74 MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < THERMISTOR (POSITIVE) > C511 1-164-217-11 CERAMIC CHIP 150PF C512 1-162-963-11 CERAMIC CHIP 680PF TH801 1-801-792-21 THERMISTOR, POSITIVE C513 1-162-963-11 CERAMIC CHIP 680PF TH802 1-809-148-11 THERMISTOR PTH8L07AR2R0M1B510 C514 1-126-391-11 ELECT CHIP 47uF...
  • Page 75 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R113 1-216-839-11 METAL CHIP 1/16W R553 1-216-845-11 METAL CHIP 100K 1/16W R116 1-216-845-11 METAL CHIP 100K 1/16W R554 1-216-845-11 METAL CHIP 100K 1/16W R122 1-216-845-11 METAL CHIP 100K 1/16W R555...
  • Page 76 SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R502 1-216-073-00 METAL CHIP 1/10W ACCESSORIES & PACKING MATERIALS R503 1-216-097-11 RES-CHIP 100K 1/10W ******************************** R504 1-216-057-00 METAL CHIP 2.2K 1/10W R505 1-216-049-11 RES-CHIP 1/10W 1-418-812-41 REMOTECOMMANDER (RM-X94) (M650) R506 1-216-035-00 RES-CHIP 1/10W...
  • Page 77 Ref. No. Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 3-014-370-21 FRAME, FITTING 3-916-012-01 BRACKET (ND), FITTING ASSIST (M600/M650) 7-682-160-01 SCREW +P 4X6 (M600/M650) X-3368-725-1 SCREW ASSY, FITTING (M600/M650) X-3378-770-1 COLLAR ASSY 3-386-828-01 SCREW, FITTING (M600R) 3-349-410-01 BUSHING (M600R) X-3366-405-1 SCREW ASSY (EXP), FITTING (M600R) 3-030-929-02 SPRING, FITTING 3-934-325-01 SCREW (+K 5X8 TP)
  • Page 78 CDX-M600/M600R/M650 Sony Corporation 9-870-132-11 2000C0457-1 Mobile Electronics Division Company Printed in Japan ©2000. 3 Published by General Engineering Dept.

This manual is also suitable for:

Cdx-m600rCdx-m650

Table of Contents