Sony CDX-M610 Service Manual

Sony CDX-M610 Service Manual

Fm/am compact disc players

Advertisement

SERVICE MANUAL
Ver 1.0 2001. 01
• The tuner and CD sections have no adjustments.

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
Other Specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block.
Tuner section
FM
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Sony Corporation
9-870-261-11
2001A0400-1
Audio Entertainment Group
© 2001. 1
General Engineering Dept.
CDX-M610
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
Power amplifier section
Outputs
Speaker outputs
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Audio outputs (3)
Power antenna relay
control lead
Power amplifier control
lead
Inputs
Telephone ATT control
lead
Illumination control lead
Treble ± 10 dB at 100 Hz
Power requirements
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 182 mm
Dimensions
× 2 × 7
(7
1/8
(w/h/d)
Approx. 182 × 53 × 163 mm
Mounting dimensions
× 2
(7
1/4
1/8
(w/h/d)
Mass
Approx. 1.5 kg (3 lb. 5 oz.)
Supplied accessories
Card remote commander
RM-X93
Parts for installation and
connections (1 set)
Design and specifications are subject to change without
notice.
FM/AM COMPACT DISC PLAYER
US Model
CDX-M610
MG-383Z-121//K
KSS-720A
in.)
1/4
× 6
in.)
1/2
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony CDX-M610

  • Page 1: Specifications

    CDX-M610 SERVICE MANUAL US Model Ver 1.0 2001. 01 • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-M610 CD Drive Mechanism Type MG-383Z-121//K SPECIFICATIONS Optical Pick-up Name KSS-720A AUDIO POWER SPECIFICATIONS Power amplifier section...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Table Of Contents

    CDX-M610 TABLE OF CONTENTS 1. GENERAL 4. DIAGRAMS Location of controls ..............4 4-1. IC Pin Descriptions ............23 Getting Started ................. 4 4-2. Block Diagram –CD Section– ........... 32 Setting the clock ..............5 4-3. Block Diagram –Tuner Section– ........33 CD Player CD/MD Unit ............
  • Page 4: General

    CDX-M610 SECTION 1 GENERAL This section is extracted from instruction manual.
  • Page 5: Setting The Clock

    CDX-M610...
  • Page 6: Radio

    CDX-M610...
  • Page 7: Other Functions

    CDX-M610...
  • Page 8: Tv/Video

    CDX-M610...
  • Page 9 CDX-M610...
  • Page 10: Connections

    CDX-M610...
  • Page 11 CDX-M610...
  • Page 12 CDX-M610...
  • Page 13: Disassembly

    CDX-M610 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. Front Panel Assy (Normal) CD Mechanism Block, Front Panel Assy Front Panel Assy (Inoperative) Sub Panel (CD) Sub Assy Motor Block Assy, Cam (R) Assy...
  • Page 14: Front Panel Assy (Inoperative)

    CDX-M610 2-2. FRONT PANEL ASSY (INOPERATIVE) 0 Lift the motor block assy slightly to make a play. 7 PTT 2.6x6 8 PTT 2.6x6 5 PTT 2.6x6 6 PTT 2.6x6 3 screw (panel) 4 spacer (arm) 9 Lift the cam (R) assy slightly to make a play.
  • Page 15: Sub Panel (Cd) Sub Assy

    CDX-M610 2-4. SUB PANEL (CD) SUB ASSY 1 CNP805 4 claw 3 PTT 2.6x6 5 claw 2 PTT 2.6 x6 6 sub panel (CD) sub assy 2-5. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder.
  • Page 16: Main Board

    CDX-M610 2-6. MAIN BOARD 4 PTT 2.6x6 6 MAIN board ground point 5 PTT 2.6x6 ground point 3 PTT 2.6x8 2 PTT 2.6x8 1 PTT 2.6x8 2-7. HEAT SINK 5 heat sink 4 PTT 2.6x8 3 PTT 2.6x8 2 PTT 2.6x12...
  • Page 17: Chassis (T) Sub Assy

    CDX-M610 2-8. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires. black white 2-9. LEVER SECTION 5 guide (disc) 6 lever (R) 3 tension spring (LR) 7 lever (L)
  • Page 18: Servo Board

    CDX-M610 2-10. SERVO BOARD 7 special screws 6 special screws 2 CN2 3 Removal the solders. 1 CN3 4 P 2x3 8 SERVO board 5 loading motor assy 2-11. SHAFT ROLLER ASSY • When installing, take note of the positions arm (roller) and washers.
  • Page 19: Floating Block Assy

    CDX-M610 2-12. FLOATING BLOCK ASSY 6 floating block assy 7 compression spring (FL) 1 tension spring (KF1) 8 compression spring (FL) 4 Fit lever (D) in the direction of the arrow. 5 Turn loading ring in the direction of the arrow.
  • Page 20: Phase Alignment

    CDX-M610 SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 4 arm (A-L) assy 5 stop ring 1.5, type-E 2 stop ring 1.5, type-E 1 arm (B-L) assy 3 spring (arm L) bracket (L) assy 3-2. CAM (L)
  • Page 21: Motor Block

    CDX-M610 3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SWITCH board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board 5 screw (+BTT) SW900 cam (L) 3-4.
  • Page 22: Arm (A-R) Assy, Arm (B-R) Assy

    CDX-M610 3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 5 stop ring 1.5, type-E 4 arm (A-R) assy 2 stop ring 1.5, type-E 3 spring (arm R) 1 arm (B-R) assy bracket (R) assy 3-6. CAM (R) 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state).
  • Page 23: Diagrams

    CDX-M610 SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC501 CXD2598Q (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name Pin Description DVDD — Digital power supply pin DVSS — Digital ground SOUT Servo brock serial data output (Not used.) SOCK Servo brock serial data read clock output (Not used.)
  • Page 24 CDX-M610 Pin No. Pin Name Pin Description Tracking error signal input Center servo analog input RFDC RF signal input ADIO Test pin (Not used.) AVSSO — Analog ground IGEN Constant current input from OP amplifier. AVDDO — Analog ground ASYO EFM full-swing output (“L”: VSS, “H”: VDD)
  • Page 25 CDX-M610 • IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name Pin Description ITRPT — Not used in this set. 2, 3 — — Not used in this set. 4, 5 — Not used in this set. OPEN...
  • Page 26 CDX-M610 Pin No. Pin Name Pin Description SENS SENS signal input — — Not used in this set. — — Not used in this set. BU.IN Back-up power detection input BUSON Bus on control input IN SW Disc in switch input (SW3)
  • Page 27 CDX-M610 • IC301 HD6432355A26F (DISPLAY CONTROL) Pin No. Pin Name Pin Description 1, 2 PG3, 4 Not used. (Open) — Ground — Not used. (Open) — Power supply pin (+5 V) 6 – 9 PC0 – 3 Not used. (Open) —...
  • Page 28 Not used. (Open) — Power supply pin (+5 V) 90 – 96 PF6 – 0 Not used. (Open) UNI-SO SONY BUS serial data output UNI-SI SONY BUS serial data input 99, 100 — Ground UNI-SCK SONY BUS serial clock input Not used.
  • Page 29 SP LATCH Spectrum analyzer display data latch signal output to display micon. System attenuate control output SYSRST Resetting for slave micon of SONY BUS system. (N/R) Forward/Reverse select output (“L”: forward, “H”: reverse) (Not used in this set.) — Power supply pin (+5 V) (NCO) Not used.
  • Page 30 CDX-M610 Pin No. Pin Name Pin Description — Power supply pin (+5 V) ST-BY Power amplifier drive output NS MASK Noise detection output (Not used in this set.) (REEL) Tape rotation detection input (Fixed at “L” in this set.) CD EJECTOK CD eject control output (Not used in this set.)
  • Page 31 CDX-M610 Pin No. Pin Name Pin Description 4V SEL 4 V select input (“H” in this set.) (P-SEL) Power select initial setting (Fixed at “L” in this set.) TUNON Tuner power control output 115, 116 LED SW1, 2 Operation/display side illumination select control output 1, 2...
  • Page 32: Block Diagram -Cd Section

    CDX-M610 4-2. BLOCK DIAGRAM — CD SECTION — TUNER RF AMP, LD APC, DIGITAL SERVO, SECTION CD SYSTEM CONTROL SYSTEM CONTROL OPTICAL PICK-UP ERROR AMP DIGITAL SIGNAL PROCESSOR (Page 33) KSS-720A IC801 (1/3) IC501 • Signal path A MUT 19...
  • Page 33: Block Diagram -Tuner Section

    CDX-M610 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 (Page 34) –1 DISPLAY BUS AUDIO IN SECTION –2 IC409(1/2) R-CH ELECTRONIC VOLUME (Page 32) AOUT IC401 –5 FD1L OUT FL SECTION LINE OUT Q202 –6 FRONT R-CH Q404 1 SEL...
  • Page 34: Block Diagram -Display Section

    CDX-M610 4-4. BLOCK DIAGRAM — DISPLAY SECTION — DISPLAY CONTROL IC301 BUS SI UNI SI UNI SO UNI SO SIGNAL IND,DET SYSTEM CONTROL (Page 33) IC407 UNI SCK IC801 (3/3) BUS CLK TUNER BUS ON BUS ON AOUT AOUT SECTION...
  • Page 35: Circuit Boards Location

    CDX-M610 • Waveforms (Servo Section) 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING (MODE:CD PLAY) BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF...
  • Page 36: Printed Wiring Boards -Cd Mechanism Section

    CDX-M610 4-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION —...
  • Page 37 CDX-M610 • Semiconductor Location Ref. No. Location IC501 Q101 (Page 41)
  • Page 38: Schematic Diagram -Cd Mechanism Section (1/2)

    CDX-M610 • Refer to page 35 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 50 for IC Block Diagrams. IC B/D (Page 39) (Page 42) Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions.
  • Page 39 CDX-M610 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 50 for IC Block Diagrams. (Page 38) IC B/D (Page 38) Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY ∗...
  • Page 40: Printed Wiring Boards -Main Section

    CDX-M610 4-9. PRINTED WIRING BOARDS — MAIN SECTION — • Semiconductor Location Ref. No. Location Ref. No. Location D301 IC802 (D302) J-11 IC901 D303 (IC902) D304 (IC903) D401 D-10 (IC905) (D402) D-10 (D403) C-10 Q101 B-11 (D502) Q102 B-11 (D601)
  • Page 41 CDX-M610 (Page 37) (Page 46)
  • Page 42: Schematic Diagram -Main Section (1/4)

    CDX-M610 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 50 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM < > : CD PLAY...
  • Page 43: Schematic Diagram -Main Section (2/4)

    CDX-M610 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 50 for IC Block Diagrams. IC B/D (Page 42) IC B/D (Page 44) (Page 45) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 44: Schematic Diagram -Main Section (3/4)

    CDX-M610 • Refer to page 47 for Waveforms. 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 50 for IC Block Diagrams. (Page 42) (Page 43) (Page 45) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 45: Schematic Diagram -Main Section (4/4)

    CDX-M610 • Refer to page 47 for Waveforms. 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 50 for IC Block Diagrams. (Page 42) (Page 43) (Page 47) (Page 44) (Page 49) IC B/D Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 46: Printed Wiring Board -Sub Section

    CDX-M610 4-14. PRINTED WIRING BOARD — SUB SECTION — (Page 41)
  • Page 47: Schematic Diagram -Sub Section

    CDX-M610 • Waveforms (Main Section) 4-15. SCHEMATIC DIAGRAM — SUB SECTION — (MODE:CD PLAY) 2.5Vp-p 32kHz IC801 (XOA) 2.5Vp-p 3.88MHz (XO) IC801 1.8Vp-p 18.43MHz (Page 45) (EXTAL) IC301 Note: • Voltage is dc with respect to ground under no-signal (detuned) condition.
  • Page 48: Printed Wiring Board -Display Section

    CDX-M610 4-16. PRINTED WIRING BOARD — DISPLAY SECTION — (Page 40) • Semiconductor Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location (D902) B-12 IC902 LED912 B-13 Q901 (D903) C-11 IC903 LED913 Q902 (D904) C-11 LED914...
  • Page 49: Schematic Diagram -Display Section

    CDX-M610 4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION — (Page 45)
  • Page 50 CDX-M610 • IC Block Diagrams IC1 CXA2596M-T6 IC7 LA6556L-TE-L IC802 BA8270F-E2 IC307 BA6288FS-E2 BUS ON APC PD AMP BUS ON SWITCH DRIVER DRIVER HOLD S-GND – OUT1 OUT2 INPUT RESET SWITCH CH2-CH4 OUTPUT – BUS ON MUTE2 35 MUTE2 POWER...
  • Page 51 CDX-M610 IC401 TDA7402TR 24 23 33 32 31 MIXER MONO- MONO- MONO- MONO- MONO- MONO- FADER FADER FADER FADER FADER FADER ACINLF FRONT SUBWOOFER SWINR ACIN +PHASE OUTPUT SWINL REAR CONTROL SELECTOR ACOUTR MAIN ACOUTL SECOND CREF VOICE BANDPASS BASS...
  • Page 52: Exploded Views

    CDX-M610 SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Accessories and packing materials and The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. hardware (# mark) list are given in 0 are critical for safety.
  • Page 53: Main Board Section

    CDX-M610 5-2. MAIN BOARD SECTION M601 TU601 F901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 51 X-3380-358-1 CHASSIS (CD) ASSY * 67 A-3283-098-A MAIN BOARD, COMPLETE A-3315-066-A SHAFT ASSY, DRIVE * 68 3-044-471-01 HEAT SINK...
  • Page 54: Front Panel Section

    CDX-M610 5-3. FRONT PANEL SECTION LCD901 LCD902 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-045-726-01 BUTTON (SOURCE) * 117 3-045-708-01 SHEET (SUB), DIFFUSION 3-045-725-01 BUTTON (+/–) * 118 3-045-707-01 PLATE (SUB) SUB, LIGHT GUIDE...
  • Page 55: Cd Mechanism Section (1)

    CDX-M610 5-4. CD MECHANISM SECTION (1) (MG-383Z-121//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 1-676-709-11 DISC IN SW BOARD 3-040-040-01 ARM (ROLLER) 3-040-039-01 CHASSIS (T) * 161 A-3294-809-A SERVO BOARD, COMPLETE 3-040-038-01 SPRING (LR), TENSION...
  • Page 56: Cd Mechanism Section (2)

    CDX-M610 5-5. CD MECHANISM SECTION (2) (MG-383Z-121//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-025-01 ARM, CHUCKING A-3307-422-A CHASSIS (M) COMPLETE ASSY 3-040-031-01 DAMPER (T) 3-040-059-01 SPRING (TR), TENSION 3-040-056-01 LEVER (D) 3-040-057-01 LEVER (LOCK)
  • Page 57: Cd Mechanism Section (3)

    CDX-M610 5-6. CD MECHANISM SECTION (3) (MG-383Z-121//K) M901 M902 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No.
  • Page 58: Electrical Parts List

    3-045-702-01 BRACKET (LCD) (MAIN) 3-045-703-01 PLATE (LCD) (MAIN), LIGHT GUIDE < DIODE > 3-045-704-01 SHEET (MAIN), DIFFUSION LED901 8-719-079-49 LED NSSW450-BRS-TVR (SONY) 3-045-705-01 SHEET (MAIN), REFLECTION LED903 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) 3-045-706-01 BRACKET (LCD) (SUB) LED904 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT)
  • Page 59 CDX-M610 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW912 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (OPEN) R933 1-216-033-00 METAL CHIP 1/10W LSW913 1-771-883-11 SWITCH, TACTILE (WITH LED) (6) R934 1-216-025-11 RES-CHIP 1/10W LSW914 1-771-883-11 SWITCH, TACTILE (WITH LED) (5)
  • Page 60 CDX-M610 LIMIT SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-676-708-11 LIMIT SW BOARD C379 1-164-156-11 CERAMIC CHIP 0.1uF C380 1-162-974-11 CERAMIC CHIP 0.01uF *************** C401 1-115-156-11 CERAMIC CHIP < CONNECTOR > C402 1-115-156-11 CERAMIC CHIP...
  • Page 61 CDX-M610 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C809 1-115-156-11 CERAMIC CHIP < JACK > C810 1-164-156-11 CERAMIC CHIP 0.1uF C812 1-164-156-11 CERAMIC CHIP 0.1uF CNP803 1-764-270-21 JACK, STEREO MINIATURE (DIA.3.5) C813 1-164-230-11 CERAMIC CHIP...
  • Page 62 CDX-M610 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > < TRANSISTOR > IC301 8-759-684-69 IC HD6432355A26F Q101 8-729-920-31 TRANSISTOR DTC343TK-T-146 IC303 8-759-277-63 IC TC7W14FU(TE12R) Q102 8-729-920-31 TRANSISTOR DTC343TK-T-146 IC306 8-759-668-14 IC PQ09DZ1U...
  • Page 63 CDX-M610 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R203 1-216-813-11 METAL CHIP 1/16W R457 1-216-841-11 METAL CHIP 1/16W R204 1-216-813-11 METAL CHIP 1/16W R458 1-216-839-11 METAL CHIP 1/16W R205 1-216-864-11 SHORT R465 1-216-839-11 METAL CHIP...
  • Page 64 CDX-M610 SERVO MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R845 1-216-821-11 METAL CHIP 1/16W R937 1-216-055-00 METAL CHIP 1.8K 1/10W R846 1-216-821-11 METAL CHIP 1/16W R938 1-216-097-11 RES-CHIP 100K 1/10W R847 1-216-821-11 METAL CHIP...
  • Page 65 CDX-M610 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C304 1-163-037-11 CERAMIC CHIP 0.022uF < TRANSISTOR > C305 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C306 1-162-965-11 CERAMIC CHIP 0.0015uF 10% Q101 8-729-904-87 TRANSISTOR 2SB1197K-T-146-R C307 1-162-962-11 CERAMIC CHIP...
  • Page 66 CDX-M610 SERVO SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R519 1-216-834-11 METAL CHIP 1/16W < IC > R520 1-216-834-11 METAL CHIP 1/16W R521 1-216-834-11 METAL CHIP 1/16W IC501 8-749-012-25 IC RS-170-TU R522 1-216-834-11 METAL CHIP...
  • Page 67 CDX-M610 Ref. No. Part No. Description Remark ************** HARDWARE LIST ************** 7-685-790-09 SCREW +PTT 2.6X4 (S) 7-685-792-09 SCREW +PTT 2.6X6 (S) 7-627-850-28 SCREW, PRECISION +P 1.4X3 7-627-553-28 SCREW, PRECISION +P 2X2.5 7-624-102-04 STOP RING 1.5, TYPE -E 7-685-793-09 SCREW +PTT 2.6X8 (S)
  • Page 68 CDX-M610...
  • Page 69 CDX-M610 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

Table of Contents