YASKAWA F7 User Manual page 193

http://www.aotewell.com
Parameter Parameter Name
No. Digital Operator Display
H3-06 Terminal A3 Gain Setting
Terminal A3 Gain
H3-07 Terminal A3 Bias Setting
Terminal A3 Bias
Terminal A2 Signal Level
H3-08 Selection
Term A2 Signal
Terminal A2 Function
H3-09 Selection
Terminal A2 Sel
H3-10 Terminal A2 Gain Setting
Terminal A2 Gain
H3-11 Terminal A2 Bias Setting
Terminal A2 Bias
Analog Input Filter Time
H3-12 Constant
Filter Avg Time
Terminal FM Monitor
H4-01 Selection
Terminal FM Sel
Denotes that parameter can be changed when the Drive is running.
Tel: +(86) 755 8660 6182
Aotewell
Table A.1 F7 Parameter List (Continued)
Description
Sets the output level when 10V is input.
Sets the frequency reference when 0V is input.
Selects the signal level of terminal A2.
0: 0 to 10Vdc (switch S1-2 must be in the OFF position).
1: -10 to +10Vdc (switch S1-2 must be in the OFF position).
2: 4 to 20mA (switch S1-2 must be in the ON position)
Selects the function of terminal A2.
Same choices as Terminal A3 Function Selection (H3-05).
Sets the output level when 10V is input.
Sets the output level when 0V is input.
This parameter adjusts the filter on all 3 analog inputs. Increase to
add stability, decrease to improve response.
Analog Outputs
Selects which monitor will be output on terminals FM and FC.
1: Frequency Reference
100% = Maximum output frequency E1-04.
2: Output Frequency
100% = Maximum output frequency E1-04.
3: Output Current
100% = Drive rated current.
5: Motor Speed
100% = Maximum output frequency E1-04.
6: Output Voltage
100% = 200/400Vac depending on Drive voltage rating.
7: DC Bus Voltage
100% = 400/800Vdc depending on Drive voltage rating.
8: Output kWatts
100% = Drive rated power.
9: Torque Reference
100% = Motor rated torque.
15:Terminal A1 Input Level
100% = 10Vdc
16:Terminal A2 Input Level
100% = 10Vdc or 20mA
17:Terminal A3 Input Level
100% = 10Vdc
18:Motor Secondary Current
100% = Motor rated secondary current.
19:Motor Excitation Current
100% = Motor rated magnetizing current.
20:SFS Output
100% = Maximum output frequency E1-04.
21:ASR Input
100% = Maximum output frequency E1-04.
22:ASR Output
100% = Maximum output frequency E1-04.
24:PID Feedback
100% = Maximum output frequency E1-04.
26:Output Voltage Reference Vq
100% = E1-05, default 240V or 480V.
27:Output Voltage Reference Vd
100% = E1-05, default 240V or 480V.
31:Not Used
32:ACR q Output (100% = Motor rated secondary current)
33:ACR d Output (100% = Motor rated magnetizing current)
36:PID Input
100% = Maximum output frequency E1-04.
37:PID Output
100% = Maximum output frequency E1-04.
38:PID Setpoint
100% = Maximum output frequency E1-04.
44:ASR Output Without Filter
45:Feedforward Control Output
100% = Motor rated secondary current.
Parameters A - 28
Aotewell
Email: Sales@aotewell.com
Control Method
Setting Factory
V/F
Range Setting
V/F
w/PG
0.0 to
100.0% A
1000.0
–100.0 to
0.0% A
+100.0
0 to 2 2 A
0 to 1F 0 A
0.0 to
100.0% A
1000.0
–100.0 to
0.0% A
+100.0
0.00 to
0.03sec A
2.00
1 to 45 2 A
http://www.aotewell.com
Open
Flux
Loop
Vector
Vector
A A A
A A A
A A A
A A A
A A A
A A A
A A A
A A A