Protect The Environment - TEFAL ActiFry express Instruction Manual

Problems Causes
You have not used the paddle.
The food has not
The food / chips have not been
been cooked
cut uniformly.
uniformly.
The paddle has been fitted
correctly but is not turning.
You are not using a potato
variety that is recommended
for chips.
The potatoes are insuffciently
washed and/or not completely
dried.
The chips are not
crunchy enough.
The chips are too thick.
There is not enough oil.
The filter is clogged.
The chips break
The quantity is too large.
during cooking.
The food stays on The pan has too much food.
the edge of the
pan.
Max level exceeded.
Faulty pan or paddle.
Cooking fluids have
leaked into the
base of the
The max level has been
appliance.
exceeded.
The appliance is not plugged in.
The LCD screen
does not work.
The lid is open.
The LCD displays The appliance is not
shows «Er» (error). functioning correctly.
You suspect there is a problem
The appliance
in the way the appliance
is abnormally noisy.
motor is working.
If you have any product problems or queries call our Customer Relations Team first for
expert help and advice: Helpline: 0345 602 1454 - UK
(01) 677 4003 - ROI
or contact us via our web site: www.tefal.co.uk
10
Solutions
Put it in position.
Cut the food / chips all to the same size.
Call the customer Helpline below.
Choose a potato variety that is
recommended for chips such as Maris Piper
or King Edwards or Rooster..
Wash potatoes for a long time to remove the
starch, drain and dry very thoroughly before
cooking. They must be completely dry.
Cut them more thinly. The maximum chip
dimensions are 13 mm x 13 mm.
Increase the amount of oil (see cooking
table p. 6 to 7..
Clean the filter.
Reduce the amount of potatoes and adjust
the cooking time.
Comply with the maximum quantities shown
on the cooking table.
Reduce the amount of food.
Reduce the quantities.
Check that the paddle is correctly positioned,
otherwise call the customer Helpline below.
Observe the max level.
Do not use ActiFry for making recipes with a
high liquid content.
Plug the appliance in.
Close the lid.
Unplug the appliance, wait for 10 seconds,
plug the appliance in again and press
button. If the LCD screen still shows Er, see
the table of error codes p. 10..
Call the customer Helpline below.
TABLE OF ERROR CODES: ER.
Er. 1 or 2 The fan is not working.
This error may appear if the
appliance has been stored for a
Er. 3
long time at too low a
temperature.
Your appliance has a fault in
Er. 4
the temperature sensor.
The voltage of your domestic
Er. 5 network is too low. Cooking
performance may be altered.
The voltage of your domestic
network is too high; for safety
Er. 6 reasons your appliance should
be protected against the risks
of overheating.

PROTECT THE ENVIRONMENT

• Your appliance has been designed to run for many years. However, when you decide to replace it,
remember to think about how you can contribute to protecting the environment.
• Before discarding your appliance you should remove the battery from the timer and dispose of it at
a local civic waste collection centre (according to model).
• The Approved Service Centres will take back any old appliances you may have so that they can be
disposed of in accordance with environmental regulations.
Check that all removable parts are
fitted and correctly positioned (bowl
ventilation output grid and removable
FR
filter, pan, lid).
Check that there are no foreign bodies in
all of these removable parts.
After checking that there are no foreign
EN
bodies in the ventilation outlets, if the
fault persists, call the customer Helpline.
Leave the appliance at an ambient
temperature of more than 15°C for one
hour before starting it up again.
If the fault persists, call the customer
Helpline.
Call the customer Helpline below.
Contact your electricity supplier.
Contact your electricity supplier.
11