Password Setting - Hitachi P1-00044-L Basic Manual

Chapter 4
[UA-01]～[UA-19]
■Parameter mode (U code)

Password setting

Code/Name
UA-01
Password for display
UA-02
Password for softlock
・When using the password, display and parameter mode
settings are locked
・The inverter will be locked by password when setting
any value other than 0000. The password can be
cancelled by entering the set password. Please note
that, the restrictions will not be cancelled if you forget
the password.
Display mode of keypad
Code/Name
00(Full display)/
01(Function-specific display)/
UA-10
Display
02(User setting)/
restriction selection
03(Data comparison display)/
04(Monitor only)
・Limit the displayed contents of the keypad.
・For more information, refer to the User's guide.
Accumulated power display adjustment/clear
Code/Name
UA-12
Accumulation output
power monitor clear
UA-13
Display gain for
accumulation input power monitor
UA-14
Accumulation output
power monitor clear
UA-15
Display gain for
accumulation output power
monitor
・If [KHC] terminal is ON, the accumulated input power
can be clear.
・If [OKHC] terminal is ON, the accumulated output power
can be clear.
Software lock operation settings
Code/Name
UA-16
Soft-Lock selection
UA-17
Soft-Lock target
selection
・Sets the software lock operation.
Keypad copy function restriction
Code/Name
UA-18
Data R/W
selection
・Restricts the copy function(Read/Write).
Keypad low battery warning
Code/Name
UA-19
Low battery warning
enable
・Sets operation for when keypad is low on battery.
Range (unit) Initial value
0000～FFFF 0000
0000～FFFF 0000
Range (unit) Initial value
00
Range (unit) Initial value
00(Disable)/
00
01(Clear)
1～1000 1
00(Disable)/
00
01(Clear)
1～1000 1
Range (unit) Initial value
00([SFT] terminal)/
00
01(Always enable)
00(All data)/
00
01(All, except speed )
Range (unit) Initial value
00(Not able to R/W)
00
01(Able to R/W)
Initial
Range (unit)
value
01(Warning)/02(Error)
For parameter configuration
Keypad communication lost operation
Code/Name
UA-20
Operation
selection when keypad
communication is lost
User-parameter setting function
Code/Name
UA-30
User-parameter auto setting
function enable
UA-31
User-parameter 1 selection
UA-32
User-parameter 2 selection
UA-33
User-parameter 3 selection
UA-34
User-parameter 4 selection
UA-35
User-parameter 5 selection
UA-36
User-parameter 6 selection
UA-37
User-parameter 7 selection
UA-38
User-parameter 8 selection
UA-39
User-parameter 9 selection
UA-40
User-parameter 10 selection
UA-41
User-parameter 11 selection
UA-42
User-parameter 12 selection
UA-43
User-parameter 13 selection
UA-44
User-parameter 14 selection
UA-45
User-parameter 15 selection
UA-46
User-parameter 16 selection
UA-47
User-parameter 17 selection
UA-48
User-parameter 18 selection
UA-49
User-parameter 19 selection
UA-50
User-parameter 20 selection
UA-51
User-parameter 21 selection
UA-52
User-parameter 22 selection
UA-53
User-parameter 23 selection
UA-54
User-parameter 24 selection
UA-55
User-parameter 25 selection
UA-56
User-parameter 26 selection
UA-57
User-parameter 27 selection
UA-58
User-parameter 28 selection
UA-59
User-parameter 29 selection
UA-60
User-parameter 30 selection
UA-61
User-parameter 31 selection
UA-62
User-parameter 32 selection
・Sets the data displayed when [UA-10]=02.
01
4-59
[UA-20]～[UA-62]
Range (unit)
00(Error)/
01(Error after deceleration stop)/
02(Ignore)/
03(Free-run)/
04(Deceleration stop)
Range (unit)
00(Disable)/
01(Enable)
no/
(parameter)
Initial
value
02
Initial
value
00
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no
no