Sony CFD-E90 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. Psyc CFD-E90
  6. Service manual

Sony CFD-E90 Service Manual

Hide thumbs Also See for CFD-E90:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.3 2005.07
AUDIO POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 4-ohm loads, both channels driven from
100 - 10 000 Hz; rated 1.5 W per channel-
minimum RMS power, with no more than 10 %
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz
Wow and flutter
Below measurable limit
Sony Corporation
9-961-974-04
2005G05-1
Personal Audio Group
© 2005.07
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD
Optical Pick-up Block Name
Section
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type

SPECIFICATIONS

Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 110 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 50 - 15 000 Hz
General
Speaker
in.) dia., 4 Ω, cone type (2)
Full range: 8 cm (3
1
⁄
4
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Power output
2 W + 2 W (at 4 Ω, 10 % harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
9 V DC, 6 size C (R14) batteries
For memory back-up:
4.5 V DC, 3 size AA (R6) batteries
For remote control:
3 V DC, 2 size AAA (R03) batteries
CD RADIO CASSETTE-CORDER
CFD-E90
US Model
Canadian Model
CFD-E95
KSM-213RDP or KSM-213CDP
KSS-213R or KSS-213C
CFD-E95
MF-E95
Power consumption
AC 14 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 13.5 h
Sony alkaline LR14: approx. 20 h
Tape playback
Sony R14P: approx. 7.5 h
Sony alkaline LR14: approx. 15 h
CD playback
Sony R14P: approx. 2.5 h
Sony alkaline LR14: approx. 7 h
Dimensions
Approx. 272 × 164 × 285 mm (w/h/d)
× 6
× 11
(10
3
⁄
1
⁄
1
⁄
inches) (incl. projecting parts)
4
2
4
Mass
Approx. 3 kg (6 lb. 10 oz) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control (1)
Design and specifications are subject to change without
notice.
E Model

Advertisement

Table of Contents
loading

Related Manuals for Sony CFD-E90

Summary of Contents for Sony CFD-E90

  • Page 1: Specifications

    4-track 2 channel stereo Sony R14P: approx. 7.5 h Other Specifications Fast winding time Sony alkaline LR14: approx. 15 h Approx. 110 sec. with Sony cassette C-60 CD player section Frequency response CD playback System TYPE I (normal): 50 - 15 000 Hz Compact disc digital audio system Sony R14P: approx.

  • Page 2: Table Of Contents

    CFD-E90 TABLE OF CONTENTS SERVICING NOTES ..........GENERAL ..............DISASSEMBLY 3-1. Disassembly Flow ............9 3-2. Cabinet Upper Assy ............9 3-3. POWER Board ..............10 3-4. TUNER Board ..............10 3-5. MAIN Board ..............11 3-6. CD Mechanism Deck (KSM-213RDP) ......11 3-7.
  • Page 3 OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY.

  • Page 4: Servicing Notes

    CFD-E90 SECTION 1 SERVICING NOTES CHUCK PLATE JIG ON REPAIRING NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. The laser diode in the optical pick-up block may suffer electro- •...
  • Page 5 CFD-E90 Ver. 1.3 [MODEL IDENTIFICATION] The CDF-E90 is available with three types and five defferent color variations. How to identify the destination, type, and color variation is shown below. – CD LID Top View – ORIGINAL TYPE LIV TYPE PSYC TYPE...

  • Page 6: General

    CFD-E90 SECTION 2 This section is extracted from instruction manual. GENERAL Basic Operations Playing a CD Use these buttons for additional operations 1, 2 ZPUSH OPEN/CLOSE VOLUME +, — Jog dial POWER Do this adjust the volume Press VOLUME +*, — (VOL +, —...

  • Page 7: Playing A Tape

    CFD-E90 Playing a tape Use these buttons for additional operations POWER VOLUME +, — m, M Press adjust the volume VOLUME +*, — (VOL +, — on the remote) stop playback Connect the supplied AC power cord. fast-forward or rewind the tape...

  • Page 8: Setting The Clock

    CFD-E90 The Timer Setting the clock Press ENTER. The clock starts from 00 seconds. — —:— — indication appears in the display until you set the clock. CLOCK/SLEEP/TIMER The time display system: 12-hour system AM 12:00 = midnight ENTER Jog dial...

  • Page 9: Disassembly

    CFD-E90 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. CABINET UPPER ASSY (page 9) 3-3. POWER 3-4. TUNER 3-8. CABINET 3-12. CD LID 3-5. MAIN BOARD BOARD BOARD FRONT SECTION...

  • Page 10: Power Board

    CFD-E90 3-3. POWER BOARD 2 two screws 1 connector (2.6 × 10) (CNP901) 5 POWER board 4 connector (CNP322) 3-4. TUNER BOARD 5 screw (2.6 × 8) 2 three screws (2.6 × 8) 3 screw (2.6 × 10) 1 connector...

  • Page 11: Main Board

    CFD-E90 3-5. MAIN BOARD 1 two flexible flat cables (CN802, 804) 1 flexible flat cable (CN310) 2 two connectors (CNP314, CN331) 3 three screws (2.6 × 8) 5 MAIN board 4 screw (2.6 × 8) 1 flexible flat cable (CN803)

  • Page 12: Optical Pick-Up (Kss-213R)

    CFD-E90 3-7. OPTICAL PICK-UP (KSS-213R) 1 two claws 3 CD cover 9 optical pick-up (KSS-213R) 2 two claws 7 flexible flat cable (16 core) 5 two screws (M2) 8 sled shaft 4 gear (A) 3-8. CABINET FRONT SECTION 1 four screws (2.6 ×...

  • Page 13: Tape Mechanism Deck (Mf-E95)

    CFD-E90 3-9. TAPE MECHANISM DECK (MF-E95) 0 three buttons (MD) (FWD, play, REC) 9 three buttons (MD) (pause, stop/eject, REW) 6 panel section qa tape mechanism deck (MF-E95) 3 two screws (2.6) 4 two screws (2.6) 7 four screws (2.6 × 10) 1 Push the button (MD) (stop/eject).

  • Page 14: Main Belt (B), Sub Belt (B)

    CFD-E90 3-11. MAIN BELT (B), SUB BELT (B) 8 main belt (B) 7 motor block 6 screw (2.6 × 4.5) 9 sub belt (B) 5 screw (2.6 × 4.5) 1 screw (2 × 4) tape mechanism deck 2 harness 3 Remove four solders.

  • Page 15: Mechanical Adjustments

    CFD-E90 SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened 1. Setting swab : MEGABASS control : OFF record/playback head pinch roller erase head rubber belts TAPE DECK SECTION 0 dB=0.775 V...

  • Page 16: Tuner Section

    CFD-E90 0 dB=1 µV AM IF ADJUSTMENT TUNER SECTION Adjust for a maximum reading on level meter [AM] 450 kHz Setting: Function : RADIO AM VCO VOLTAGE ADJUSTMENT BAND button : AM Frequency Display Reading on Digital Voltmeter 530 kHz 1.0 ±...
  • Page 17 CFD-E90 Adjustment Location: – TUNER BOARD (Component Side) – T2 FM IF Adjustment AM VCO Voltage Adjustment T1 AM IF Adjustment FM VCO Voltage Adjustment FM Tracking Adjustment AM Tracking Adjustment – TUNER BOARD (Conductor Side) – (ANT) (VT) (GND) –...

  • Page 18: Cd Section

    CFD-E90 CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias. Focus Bias Check 1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3.

  • Page 19: Diagrams

    CFD-E90 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – OPTICAL PICK-UP BLOCK CD L-OUT LCHO INTERPOLATION (KSS-213R) SLICE ERROR MUTE DIGITAL FIN2 EFMIN (Page 21) LEVEL CORRECTION & FILTER CONTROL AUDIO CD ATTENUATION & RCHO R-CH DETECTOR DEEMPHASIS...

  • Page 20: Block Diagram - Tuner Section

    CFD-E90 6-2. BLOCK DIAGRAM – TUNER Section – FM IFT FM IF ANT1 FM TELESCOPIC ANTENNA FM/AM RF AMP, MIX, OSC, FM/AM IF AMP, DET, MPX L-CH L-OUT TU L-OUT DET- MPX- RF-IN MIX-OUT IF-IN FM IF RF AMP MUTE...

  • Page 21: Block Diagram - Main Section

    CFD-E90 6-3. BLOCK DIAGRAM – MAIN Section – INPUT SELECT, REC/PB PRE AMP CD L-OUT IC301 VREF (Page 19) POWER MIC IN MUTE IC304 L.CD R-CH ELECTRICAL VOLUME L.RAD MUTE IC302 STANDBY SWITCH R-CH L-OUT L OUT L-IN L IN L.LO...

  • Page 22: Block Diagram - Power Supply Section

    CFD-E90 Ver 1.1 6-4. BLOCK DIAGRAM – POWER SUPPLY Section – LIQUID CRYSTAL DISPLAY LCD401 REMOTE CONTROL RECEIVER IC401 CD +6V SYSTEM CONTROLLER IC801 6V-CHK 41 (3/3) 3V-CHK 42 CD +3.3V CD +3.3V REGULATOR REGULATOR Q957 Q955 CD POWER ON/OFF CONTROL...

  • Page 23: Note For Printed Wiring Boards And Schematic Diagrams

    CFD-E90 Ver 1.1 6-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location (In addition to this, the necessary note is printed in each block) Note on Printed Wiring Boards: Note on Schematic Diagram: • X : parts extracted from the component side.

  • Page 24: Printed Wiring Board - Cd Section

    CFD-E90 6-6. PRINTED WIRING BOARD – CD Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. CD BOARD R715 R714 C727 JW703 JW705 C711 C709 FB701 C716 R723 C754 JC704 R732 JW730 C755 C717 IC701...

  • Page 25: Schematic Diagram - Cd Section

    CFD-E90 Ver 1.1 6-7. SCHEMATIC DIAGRAM – CD Section – • See page 36 for Waveforms. • See page 36 for IC Block Diagrams. C726 1000p C725 1000p C724 C723 0.01 C722 C721 C720 S701 (LIMIT) C750 C746 C747 R724...

  • Page 26: Printed Wiring Board - Tuner Section

    CFD-E90 6-8. PRINTED WIRING BOARD – TUNER Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. ANT1 TELESCOPIC ANTENNA JC12 (ANT) MAIN BOARD KH803 (Page 29) MAIN BOARD KH804 (Page 29) 1-688-455- (11) • Semiconductor Location Ref.

  • Page 27: Schematic Diagram - Tuner Section

    CFD-E90 6-9. SCHEMATIC DIAGRAM – TUNER Section – • • See page 36 for Waveform. See page 36 for IC Block Diagrams. AM FERRITE-ROD ANTENNA 220p (VT) KV1520NT 100p AM OSC 0.22 0.001 JC12 JC11 0.01 220k 100p 0.01 0.001 100k 0.01...

  • Page 28: Printed Wiring Board - Tape Deck Section

    CFD-E90 6-10. PRINTED WIRING BOARD – TAPE DECK Section – 6-11. SCHEMATIC DIAGRAM – TAPE DECK Section – • See page 36 for Waveform. • See page 36 for IC Block Diagram. • :Uses unleaded solder. See page 23 for Circuit Boards Location.

  • Page 29: Printed Wiring Board - Main Section

    CFD-E90 6-12. PRINTED WIRING BOARD – MAIN Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. CD BOARD TUNER BOARD TUNER BOARD POWER BOARD CNP702 CNP1 CNP1 KH311 (Page 24) (Page 26) (Page 26) (Page 34)

  • Page 30: Schematic Diagram - Main Section (1/2)

    CFD-E90 6-13. SCHEMATIC DIAGRAM – MAIN Section (1/2) – • See page 36 for IC Block Diagram. (1/2) C331 R145 R330 C332 1000 C133 2.2k 0.01 R126 C124 0.022 R146 C134 220k C110 R125 R149 R143 2.2k 100k R128 Q125...

  • Page 31: Schematic Diagram - Main Section (2/2)

    CFD-E90 6-14. SCHEMATIC DIAGRAM – MAIN Section (2/2) – • • See page 36 for Waveforms. See page 39 for IC Pin Function Description. (2/2) RESET SIGNAL GENERATOR IC802 BD4727G-TR R842 R843 CN802 R841 COM0 COM0 COM1 COM1 CN310 COM2...

  • Page 32: Printed Wiring Boards - Panel Section

    CFD-E90 6-15. PRINTED WIRING BOARDS – PANEL Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. (Page 29) MAIN BOARD D406 LCD BOARD CNP314 OPR/BATT S403 R404 CLOCK/SLEEP/ R406 TIMER R425 R424 R403 JC405 R402...

  • Page 33: Schematic Diagram - Panel Section

    CFD-E90 6-16. SCHEMATIC DIAGRAM – PANEL Section – COM0 COM0 LCD401 COM1 COM1 LIQUID CRYSTAL DISPLAY COM2 COM2 COM3 COM3 SEG0 SEG0 SEG1 SEG1 SEG2 SEG2 SEG3 SEG3 SEG4 SEG4 SEG5 SEG5 SEG6 SEG6 RE401 SEG7 SEG7 ENCODER IC401 SEG8...

  • Page 34: Printed Wiring Boards - Power Section

    CFD-E90 Ver 1.1 6-17. PRINTED WIRING BOARDS – POWER Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. POWER BOARD RELAY BOARD HEADPHONE BOARD C129 KH311 JC301 C130 C230 CN322 R333 (R-CH) J321 MAIN C128...

  • Page 35: Schematic Diagram - Power Section

    CFD-E90 Ver 1.1 6-18. SCHEMATIC DIAGRAM – POWER Section – R231 R131 4.7k 4.7k R232 C324 0.01 R132 J321 (PHONES) R324 2.2k POWER AMP IC304 D323 BA5417 1SS355TE-17 R323 KH324 C323 CN324 C128 1000p C131 CN325 C130 KH322 CN322 C228...
  • Page 36 CFD-E90 • Waveforms • IC Block Diagrams – CD Board – – TUNER Board – – MAIN Board – – CD Board – 1 IC701 4 (RF) (CD Play mode) 5 IC2 w; (XOUT) ea IC801 ua (XT2) IC701 LC78646E-E...
  • Page 37 CFD-E90 IC702 BA5826FP-E2 SP– D.BUFF SL– D.BUFF LEVEL D.BUFF SHIFT D.BUFF SPIN LEVEL SHIFT SLIN THERMAL SHUT-DOWN MONITOR (SLIN) REG–B VREF REGO MUTE (FIN) DRIVER MUTE (TIN) LEVEL LEVEL SHIFT D.BUFF SHIFT D.BUFF F– T– D.BUFF D.BUFF OPOUT OPIN – TUNER Board –...

  • Page 38: Pre Board

    CFD-E90 IC2 LC72137M-TLM-E XOUT REFERENCE DIVIDER AOUT PHASE 12BITS DETECTOR PROGRAMMABLE CHARGE DIVIDER PUMP UNLOCK DETECTOR POWER ON RESET SWALLOW COUNTER FMIN 1/16,1/17 4BITS UNIVERSAL COUNTER AMIN IFIN – PRE Board – – MAIN Board – IC301 TA2068N IC302 PT2257-S...
  • Page 39 CFD-E90 • IC Pin Function Description MAIN BOARD IC801 µPD789478GC-A04-8BT (SYSTEM CONTROLLER) Pin No. Pin Name Description 1, 2 — Not used 3 to 5 VLC2 to VLC0 — Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage...
  • Page 40 CFD-E90 Pin No. Pin Name Description Sub system clock input terminal (32.768 kHz) Sub system clock output terminal (32.768 kHz) — Power supply terminal (+3.3V) — Ground terminal Main system clock input terminal (4.19 MHz) Main system clock output terminal (4.19 MHz) System reset signal input “L”: reset...

  • Page 41: Exploded Views

    CFD-E90 Ver. 1.3 SECTION 7 EXPLODED VIEWS NOTE: The components identified by mark • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they 0 or dotted line with mark 0 are may have some difference from the original are seldom required for routine service.

  • Page 42: Cabinet Front Section

    CFD-E90 Ver. 1.3 7-2. CABINET FRONT SECTION MD block section panel section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-263-837-01 LID, CASSETTE (WHITE: PSYC) X-3384-728-1 CABINET (FRONT) SUB ASSY 3-263-837-11 LID, CASSETTE (BLACK: PSYC) (for BLACK: PSYC) (US)

  • Page 43: Panel Section

    CFD-E90 Ver. 1.3 7-3. PANEL SECTION LCD board section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-656-01 BUTTON (CENTER) 3-250-750-12 BUTTON (CD) (REW) (TUNE -) (DISPLAY. CLOCK./SLEEP/TIMER. ENTER) (SILVER: ORIGINAL/WHITE: ORIGINAL) (WHITE: LIV, PSYC) 3-250-750-22 BUTTON (CD) (REW) (TUNE -) (BLACK: PSYC)

  • Page 44: Lcd Board Section

    CFD-E90 Ver. 1.3 7-4. LCD BOARD SECTION LCD401 not supplied board IC401 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-675-01 PLATE, LIGHT GUIDE 3-254-939-01 SHEET (23 PIN FFC), PROTECTION 3-247-669-01 HOLDER, LCD 3-254-940-01 SHEET (6 PIN FFC), PROTECTION...

  • Page 45: Md Block Section

    CFD-E90 Ver. 1.3 7-5. MD BLOCK SECTION not supplied supplied tape mechanism deck section (MF-E95) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-659-01 BUTTON (MD) (PAUSE) (X) 3-247-658-11 BUTTON (MD) (FWD) (M) (WHITE: LIV, PSYC)

  • Page 46: Cabinet Upper Section

    CFD-E90 Ver. 1.3 7-6. CABINET UPPER SECTION S901 not supplied (HEADPHONE board) CD block section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-951-620-01 SCREW (2.6X8), +BVTP 3-263-846-41 CABINET (UPPER) (WHITE: PSYC) (CND) * 252 A-3347-999-A MAIN BOARD, COMPLETE (E)

  • Page 47: Cabinet Under Section

    CFD-E90 Ver. 1.3 7-7. CABINET UNDER SECTION speaker box section J901 T901 ANT1 F901 BATTERY (2) board BATTERY (3) board BATTERY (1) board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.

  • Page 48: Speaker Box Section

    CFD-E90 7-8. SPEAKER BOX SECTION not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-672-01 BOX, SPEAKER 3-250-730-01 COVER (R), DUCT 4-951-620-01 SCREW (2.6X8), +BVTP 1-825-474-11 SPEAKER (8cm) (R) 3-250-729-01 COVER (L), DUCT...

  • Page 49: Cd Block Section

    CFD-E90 7-9. CD BLOCK SECTION optical pick-up section (KSM-213RDP) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-923-736-01 COVER, CD * 404 A-3683-956-A CD BOARD, COMPLETE 3-931-379-31 RUBBER, VIBRATION PROOF 3-931-379-21 RUBBER, VIBRATION PROOF...

  • Page 50: Optical Pick-Up Section (Ksm-213Rdp)

    CFD-E90 Ver 1.1 7-10. OPTICAL PICK-UP SECTION (KSM-213RDP) not supplied (M901) supplied M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.

  • Page 51: Tape Mechanism Deck Section (Mf-E95)

    CFD-E90 7-11. TAPE MECHANISM DECK SECTION (MF-E95) not supplied M901 HRP301 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-244-086-01 ARM, PINCH ROLLER 3-244-083-01 + SCREW BIND DT M2X6 3-244-079-01 BELT (B), SUB A-3172-063-A MECHANISM DECK ASSY (MF-E95)

  • Page 52: Electrical Parts List

    CFD-E90 Ver 1.1 SECTION 8 ELECTRICAL PARTS LIST BATTERY (1) BATTERY (2) BATTERY (3) NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service.
  • Page 53 CFD-E90 HEADPHONE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JC702 1-216-864-11 SHORT CHIP HEADPHONE BOARD JC703 1-216-864-11 SHORT CHIP ***************** JC704 1-216-821-11 METAL CHIP 1/10W < JACK > < FERRITE BEAD > J321 1-815-325-11 JACK (PHONES)
  • Page 54 CFD-E90 Ver. 1.3 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R409 1-216-825-11 METAL CHIP 2.2K 1/10W C222 1-162-964-11 CERAMIC CHIP 0.001uF R410 1-216-829-11 METAL CHIP 4.7K 1/10W C224 1-164-227-11 CERAMIC CHIP 0.022uF C225 1-162-966-11 CERAMIC CHIP 0.0022uF 10%...
  • Page 55 CFD-E90 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R225 1-216-825-11 METAL CHIP 2.2K 1/10W R226 1-216-817-11 METAL CHIP 1/10W D322 8-719-988-61 DIODE 1SS355TE-17 R227 1-216-833-11 METAL CHIP 1/10W D801 8-719-083-93 DIODE KDS120-RTK...
  • Page 56 CFD-E90 Ver 1.1 MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R841 1-216-841-11 METAL CHIP 1/10W R842 1-216-841-11 METAL CHIP 1/10W R959 1-216-809-11 METAL CHIP 1/10W R843 1-216-841-11 METAL CHIP 1/10W R960 1-216-833-11 METAL CHIP...
  • Page 57 CFD-E90 Ver 1.1 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R953 1-216-821-11 METAL CHIP 1/10W R954 1-216-821-11 METAL CHIP 1/10W D323 8-719-988-61 DIODE 1SS355TE-17 R955 1-216-833-11 METAL CHIP 1/10W D901 8-719-063-79 DIODE 1N4002B...
  • Page 58 CFD-E90 RELAY TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > A-3663-818-A TUNER BOARD, COMPLETE *********************** Q301 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q302 8-729-907-00 TRANSISTOR DTC114EU < CAPACITOR > Q303 8-729-907-00 TRANSISTOR DTC114EU 1-162-923-11 CERAMIC CHIP 47PF <...
  • Page 59 CFD-E90 Ver 1.1 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-864-11 SHORT CHIP < CONNECTOR > 1-216-835-11 METAL CHIP 1/10W 1-216-817-11 METAL CHIP 1/10W * CNP1 1-785-663-11 PIN, CONNECTOR (PC BOARD) 11P 1-216-815-11 METAL CHIP...
  • Page 60 CFD-E90 Ver. 1.3 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ACCESSORIES ************ 1-590-342-12 CORD, POWER (E) 1-782-126-11 CORD, POWER (EXCEPT E) 2-109-740-11 LID, BATTERY CASE (for RMT-CE90A/WIC) (WHITE: PSYC) 2-109-740-21 LID, BATTERY CASE (for RMT-CE90A/BC)
  • Page 61 CFD-E90 US Model Canadian Model SERVICE MANUAL E Model Ver 1.2 2004.06 SUPPLEMENT-1 File this supplement with the service manual. Subject: Change of Optical Pick-up Block (KSM-213RDP→KSM-213CDP) (SPM-04041) Optical pick-up block is changed from KSM-213RDP to KSM-213CDP in the midway of production.
  • Page 62 CFD-E90 OPTICAL PICK-UP SECTION (KSM-213CDP) not supplied not supplied (M701 (SPINDLE)) M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
  • Page 63 CFD-E90 MEMO...

  • Page 64: Revision History

    CFD-E90 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.01...

Table of Contents