Page 1
Rev.00 TOSHIBATEC SINGAPORE PTE LTD The content of this document is " TOSHIBA TEC SINGAPORE Intellectual Property". It is strictly confidential and is not to be disclosed, reproduced, or used without the written agreement from TOSHIBA TEC SINGAPORE PTE LTD...
Page 2
History of Changes Rev No. Date Page *Action Description of Change 08Jun'11 version Note: *Action - Change / Add / Delete DB-EA4D Command manual (rev.00)
Maximum Length = 554.8mm (for each side) Paper cutter Full cut (Rotary type) : Option Media Max 216mm (W) x 7 inch (diameter) Dual color Not support Black Dot Mark Support Label mode Support Duplex printing Support DB-EA4D Command manual (rev.00)
GS d 13H 1DH 64H 12H Label cut position adjustment GS d 14H 1DH 64H 14H Print density adjustment GS d 15H n 1DH 64H 15H n Sensor level adjustment GS d 16H 1DH 64H 16H EEPROM reset DB-EA4D Command manual (rev.00)
Page 7
UDP 3001 port command ESC n 20 1B 6E 20 All Ethernet Information ESC n 21 1B 6E 21 Serial number ESC n 22 1B 6E 22 Model number ESC n 23 1B 6E 23 MAC address DB-EA4D Command manual (rev.00)
Thermal head temperature No error Error Black mark detection error No error Error Paper Empty No error Error Cover open Close Open Unable to load paper Success Unable CAM motor jam (1 or 2 No error Error DB-EA4D Command manual (rev.00)
Recover from an error state after clearing the Receive buffer and Print buffers. This sequence is ignored except when the printer is busy due to an error condition. n = 2: Make H/W reset by watchdog timer. Printer initializes itself same as power-on initialization. DB-EA4D Command manual (rev.00)
Remote diagnostic item Function Cover open tally, Return Cover open tally (total 10 bytes) (8 digit ASCII numeric) n (hex) Remote diagnostic item Function Max temperature tally Return Max temperature tally (total 10 bytes) (8 digit ASCII numeric) DB-EA4D Command manual (rev.00)
If this command is sent without the cutter option, paper will be fed to the manual cut position. After that paper will be returned to the standby position when Print command is sent even if that paper was not cut manually. DB-EA4D Command manual (rev.00)
ESC Q n m Hexadecimal: 1B 51 n m Decimal: 29 81 n m Value of n: 00H: Black mark 01H: Document length 02H: Label 03H: Perforation (with hole) 04H: Cut Sheet Values of m: Reserved (0x00) DB-EA4D Command manual (rev.00)
Page 15
The origin (offset value = 0x00) of cut position is the edge of a black mark on the side of the paper feed direction. If cut position is required to shift to any position depending on unique media, this parameter will be used. DB-EA4D Command manual (rev.00)
After that, the printer performs this command. As for the cut position, it is cut according to the setting of paper type. Refer to Printer Configuration Form in Appendix. DB-EA4D Command manual (rev.00)
BM to cut position (w/o Cutter). If the paper type is Label mode, the paper is cut at the next gap (w/ Cutter) or fed the next gap to cut position (w/o Cutter). DB-EA4D Command manual (rev.00)
BM (w/ Cutter) or fed the next BM to cut position (w/o Cutter). If the paper type is Label mode, the paper is cut at the next gap (w/ Cutter) or fed the next gap to cut position (w/o Cutter). DB-EA4D Command manual (rev.00)
This command performs label cut position adjustment test. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. This command should be sent to the printer separately. DB-EA4D Command manual (rev.00)
This command re-stores the default value to EEPROM. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. This command should be sent to the printer separately. DB-EA4D Command manual (rev.00)
00000001. If there are any printable data when the printer receives this command, the printer prints out previous data. After that, the printer performs this command. The print layout is same as the simplex printing of Dot check pattern print test. DB-EA4D Command manual (rev.00)
After that, the printer performs this command. The print layout is same as the simplex printing of Graphics pattern print test. 1st Page Front side Back side 00000001 See Front side 2nd Page Front side Back side 00000002 See Back side DB-EA4D Command manual (rev.00)
Download data size. value of d: Download data (Not use by FTP) Downloads and writes data to the flash memory. The printer returns ACK(0x06) when downloaded data is written to the flash memory normally. DB-EA4D Command manual (rev.00)
When the printer receives this command in the Main F/W, it returns ACK(06H). When the printer receives this command in the Boot FW, it returns NACK (15H). 2.2.37 Reboot the Printer ASCII: GS FFH Hexadecimal: 1D FF Decimal: 29 255 The printer reboots when it receives this command. DB-EA4D Command manual (rev.00)
Values of i: Reserved (0x00) This command specifies the printing side in the duplex printing mode. The printing side can be changed several times freely on a logical page. This command is ignored in simplex printing model. DB-EA4D Command manual (rev.00)
In the case of the paper cut command, the paper is cut immediately and then the paper is returned to the standby position. This command is ignored in simplex printing mode. DB-EA4D Command manual (rev.00)
Page 29
Transporting to the cut position by Form Feed. 7. Perform Knife Cut by 1B 69H -> The paper is cut at the end of the page and the left paper in the printer is returned to the standby position automatically. DB-EA4D Command manual (rev.00)
Page 30
14. Perform Knife Cut by 1B 69H -> The paper is cut at the end of the page even if there is no data in the back side. -> The paper is cut at the end of the longer page and the left paper in the printer is returned to the standby position automatically DB-EA4D Command manual (rev.00)
Page 31
13. Perform Knife Cut by 1B 69H -> The paper is cut at the end of the page even if there is no data in the back side. -> The paper is cut at the end of the page and the left paper in the printer is returned to the standby position automatically DB-EA4D Command manual (rev.00)
1 = Ethernet 2 = Parallel The value which specified by n is stored in EEPROM as Interface Type, and "Reboot" will be performed. If some data are sent following this command, they will be cleared (discarded). DB-EA4D Command manual (rev.00)
Printer status Response Cutting (Printing complete) Printer status Response (Cutting complete) Used Printer Class (Control Transfer) for Real Time commands Used Printer Class (Bulk OUT) for Print data Used Printer Class (Bulk IN) for Batch commands DB-EA4D Command manual (rev.00)
Flash Cycle : xxxxxxxxxx, xxxxxxxxxx Cover Open : xxxxxxxxxx, xxxxxxxxxx Max Temperature : xxxxxxxxxx, xxxxxxxxxx Paper Jam : xxxxxxxxxx, xxxxxxxxxx CAM motor Jam : xxxxxxxxxx, xxxxxxxxxx Knife Cut : xxxxxxxxxx, xxxxxxxxxx Cutter Jam : xxxxxxxxxx, xxxxxxxxxx DB-EA4D Command manual (rev.00)
Not affect GS DC3 1DH 13H Download to Flash Memory Not affect GS 80H 1DH 80H Reboot the Printer to Switch to Main Firmware Not affect GS F0H 1DH F0H Check current active FW Not affect DB-EA4D Command manual (rev.00)