Page 2
HCD-TB20 MODEL IDENTIFICATION AM tuner section Tuning range – Back Panel – European models: 531 – 1,602 kHz (with the interval set at 9 kHz) Pan-American models: 531 – 1,710 kHz (with the interval set at 9 kHz) 530 – 1,710 kHz...
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE circuit board (within 3 times). COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS • Be careful not to apply force on the conductor when soldering APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS or unsoldering.
Page 5
HCD-TB20 Service position of the CD mechanism deck MAIN board BD board Jig cord : J-2501-208-A Service position of the TAPE cassette mechanism deck Jig cord : J-2501-082-A MAIN board TC Deck section...
HCD-TB20 SECTION 2 This section is extracted GENERAL from instruction manual. A – G M – Z A – G M – Z CD disc tray qk (8) MD (VIDEO) 9 (27) CHECK 8 (11) MENU/NO wa (13) CD SYNC wj (19)
HCD-TB20 Setting the clock Loading a CD Press DISC 1 – 3 Z. Turn on the system. The disc tray opens. Press CLOCK/TIMER SET on the remote. Place a CD with the label side up on the disc tray. Press . or > on the remote to set the hour.
HCD-TB20 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. SIDE PANEL (Page 9) TOP PANEL • The dotted square with arrow ( ) prompts you to move to the next (Page 9) job when all of the works within the dotted square ( )are completed.
HCD-TB20 3-5. PANEL Board front panel assy qd connector (CN720) qs PANEL board (Remove in the direction 9 three claws of the arrow) 0 two claws 7 four screws ( +BVTP 2.6 × 8 ) 8 ten screws 5 CD Lid ( +BVTP 2.6 ×...
HCD-TB20 3-11. CD Mechanism Deck (CDM63E) 3 chassis assy 5 CD mechanism deck (CDM63E) 2 two screws ( +BVTP 3 × 8) 1 three screws ( +BVTP 3 × 8 ) 4 four screws ( +BVTP 3 × 8 ) Note: When installing the CD mechanism, the four bosses must be aligned with the specified positions.
HCD-TB20 3-15. TRAY SENSOR Board 6 holder (sensor) 2 two screws (+BTTP M2.6) 5 TRAY SENSOR board 1 Rotate the cam, and lift up the stocker at the full. 4 two screws (+BTTP M2.6) stocker 3-16. Slider (Loading), Gear (Slider) 3 two screws (+BTTP M2.6)
HCD-TB20 3-17. Stocker Assy 4 stocker assy 2 screw (+BTTP M2.6) 3 slide the slider (BU.L), slider (BU.R) in the direction of arrow A at the full. 1 screw (+BTTP M2.6) 3-18. DISC SENSOR Board 2 CD base unit assy 4 DISC SENSOR board 3 two screws (+BTTP M2.6)
HCD-TB20 3-20. Motor Assy (M721), MOTOR Bard belt connector (CN702) two screws (+BTTP M2.6) MOTOR board bottom view MOTOR board Remove two solders. motor assy (M721)
HCD-TB20 SECTION 4 TEST MODE [CD Ship Mode] 11. During the recording by tuning m/M knob, the Tape • T his mode moves the optical pick-up to the position durable to (Deck) is selected and tape is rewound. Tape stops at around vibration.
HCD-TB20 SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775V Clean the following parts with a denatured alcohol-moistened swab: Demagnetize the record/playback head with a head demagnetizer. record/playback heads pinch rollers Do not use a magnetized screwdriver for the adjustments.
Page 24
HCD-TB20 Mode: Playback Record Bias Adjustment test tape Procedure: MAIN board P-4-A100 CN322 (10kHz, –10dB) Pin 5 or TP42 (L-CH) oscilloscope INTRODUCTION When set to the test mode performed in Tape Speed Adjustment, Pin 6 (GND) when the tape is rewound after recording, the “REC memory mode”...
Page 25
HCD-TB20 Record Level Adjustment CD SECTION Procedure: Note : 1. CD Block is basically designed to operate without adjustment. INTRODUCTION Therefore, check each item in order given. When set to the test mode performed in Tape Speed Adjustment, 2. Use YEDS-18 (3-702-101-01) unless otherwise indicated.
Page 26
HCD-TB20 Note: Clear RF signal waveform means that the shape “ ‡ ” can be Adjustment Location: clearly distinguished at the center of the waveform. [BD BOARD] (Conductor Side) RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns level : 0.65 ± 0.15Vp-p (RFDC) 1.1 ±...
HCD-TB20 SECTION 7 DIAGRAMS 7-1. Circuit Boards Location TRANS board VOL SEL board VOL board DISPLAY board TC board PANEL board AMP board MAIN board FRONT INPUT board TRAY SENSOR board SUB POWER board IN OUT SW board MOTOR board...
Page 28
HCD-TB20 THIS NOTE IS COMMON FOR PRINTED WIRING • Indication of transistor BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) These are omitted. For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
7-2. Block Diagrams CD Section • R-ch is omitted due to same as L-ch. • Signal Path : CD :DIGITAL OUT OPTICAL PICK-UP IC101 DIGITAL SERVO BLOCK DIGITAL SIGNAL PROCESSOR IC103 (A-MAX.3) D/A CONVERTER RF AMP IC351 DIGITAL D OUT (OPTICAL) RFAC RFAC...
HCD-TB20 • WAVEFORMS 7-21. IC Pin Function Description • IC401 M30622MGN-A00FP MASTER CONTROL (MAIN BOARD) – BD SECTION – Pin No. Pin Name Description IC101 ta IC101 el – Not used (RFAC)(CD Play mode) (FE)(CD Play mode) RDS DATA RDS DATA signal input...
Page 51
HCD-TB20 Pin No. Pin Name Description BACK LIGHT Back light LED control signal output VOL B Volume signal input from the rotary encoder VOL A Volume signal input from the rotary encoder LDON LDON signal output to IC103(CXA2581N) – Not used (open)
HCD-TB20 SECTION 8 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one. in the exploded views are not supplied.
HCD-TB20 8-4. CD Mechanism Deck Section -1 not supplied not supplied not supplied not supplied not supplied not supplied supplied not supplied not supplied not supplied CD mechanism deck section-2 Ref. No. Part No. Description Remarks Ref. No. Part No.
HCD-TB20 8-6. Base Unit Section (BU-30) not supplied Ref. No. Part No. Description Remarks 3-531-576-11 RIVET A-4728-678-A BD BOARD, COMPLETE 4-233-832-01 GEAR (LB) The components identified by mark 0 or dotted line with mark 0 are critical for safety. 4-233-831-01 GEAR (LA) Replace only with part number specified.
HCD-TB20 SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • CAPACITORS: • SEMICONDUCTORS parts list may be different from the parts uF: µF In each case, u: µ, for example: specified in the diagrams or the components •...
Page 72
HCD-TB20 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...