Advertisement
mode and adjust the slider on the nozzle on ALL FLOORs. In this position brushes
and wiper blade are raised while wheels are lowered to allow a perfect ease of
movement on such surfaces. [8b]
- Deep Carpet Cleaning: Press the pedal on the nozzle on Carpet mode and adjust
the slider on the nozzle on DEEP CARPET CLEANING. In this position brushes,
wheels and wiper blade are raised for a deeper cleaning of your carpet. [8c]
WARNING: It is recommended to avoid potential scratching of wooden
floors that the pedal is not set on hard floor mode and the slider on deep
carpet cleaning.
3.
switch the cleaner on by pressing the on/off pedal on the cleaner main body.
4.
slide Variable power control to increase or decrease the power. [9]
5.
Adjust the suction regulator to the desired level.
6.
switch off at the end of use by pressing the on/off Pedal.
PARKING AND STORAGE SECTION
1.
The tube can be parked on the back or on the bottom of the cleaner for storage or
temporary storage while in use. [10]
The hose, tube and nozzle can be in Nano Pack™ storage position when not in use*: [11]
2.
A. Retract the telescopic tube to its storage length.
B. Remove the nozzle from the end of the telescopic tube.
C. Remove the hose handle from the telescopic tube.
D. Lift the hose holder at the rear of the cleaner and wrap the flexible hose around
the product.
E. Park the hose handle on the product through the handle holder.
F. Assemble the nozzle into the parking slot underneath the product.
G. Assemble the telescopic tube into the remaining parking slot underneath the
product.
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1.
Lift the bag door Latch to open the bag door, close the bag to avoid dust escaping
by pulling the tongue and remove the bag [12]. The full dust bag should be disposed
of correctly and carefully.
2.
Fold a new bag as shown on the bag and fit by inserting the collar into the bag
holder. [13]
3.
Close the Bag door.
REMEMBER: The bag check indicator may be red if an obstruction has occurred. In this
case refer to 'Removing a Blockage From the system'.
Cleaning the Filter:
To maintain optimum performance of your cleaner, please wash the pre-motor filter and
exhaust filter after each 5 bag changes.
Cleaning the pre-motor filter:
1.
Lift the bag door latch to open the bag door.
2.
To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. [14]
3.
Remove the filter from the holder. [14]
4.
Wash it in lukewarm water, and allow it to dry thoroughly before re-inserting it into
the cleaner.[16,17,18]
Cleaning the exhaust filter:
1.
To remove the exhaust filter, open the bag door and remove the filter pack. [15]
2.
Wash the filter in lukewarm water and allow it to dry thoroughly before re-inserting
it into the cleaner. [16,17,19]
REMEMBER: Do not use hot water or detergents. In the unlikely event of the
filters becoming damaged, fit a Genuine Hoover replacement. Do not try and
use the product without a dust bag or filter fitted.
Cleaning the permanent cloth dust bag* (certain models only)
To maintain optimum performance we recommend that you wash the permanent cloth
dust bag under lukewarm water after every 5 full bags. Remove excess water and leave
to dry fully re-inserting it into the cleaner.
Removing a blockage from the system
If the bag check indicator is red:
1.
Check if the bag is full. If so, refer to 'Replacing The Dust Bag'.
2.
If it is not full, then;
A. Do the filters need cleaning? If so, refer to 'Cleaning the Filter'.
B. Check if there is any other blockage in the system - Use a rod or a pole to
remove any blockage from telescopic tube or flexible hose.
WARNING*: - The bag check indicator will remain red if the cleaner is used when the bag
is full, if there is a blockage or if the filters are dirty. If used for a period over ten minutes
with the bag check indicator red,an electronic cut out will switch the cleaner off to prevent
any risk of overheating. If this should happen,switch the cleaner off,unplug and correct
the fault(see 'Removing a blockage'). The cut out will automatically reset upon switching
the cleaner back on.
Battery Replacement
This cleaner is fitted with a rechargeable Lithium ion battery pack which is replaceable.
WARNING: Only use approved replacement parts for your cleaner. Using parts not
validated by Hoover is dangerous and will invalidate your guarantee.
WARNING: Do not try to open the battery pack and repair it by yourself.
1.
Press the battery release button and the battery pack will be ejected automatically.
2.
Remove the battery pack slowly from the cleaner.
3.
Remove the old battery pack and replace it with a new one.
4.
Dispose of the batteries safely.Used batteries should be taken to a recycling station
and not disposed of with household waste.
4
*Certain Models Only
**May vary according to the model
GB
Advertisement
