Viewing Device Information - Garmin FORETREX 601 Owner's Manual

Viewing Device Information

You can view the unit ID, software information, and regulatory
information.
1
From the menu page, select SETUP > ABOUT FORETREX.
2
Select .
Viewing Satellites
The satellite page shows your current location, GPS accuracy,
satellite locations, and signal strength. For more information
about GPS, go to www.garmin.com/aboutGPS.
1 From the menu page, select GPS.
The bars represent the strength of each satellite signal
received (the number of satellites appears below each bar).
White bars indicate that the device is still collecting data.
Solid bars indicate the device has acquired satellite signals.
2
Select ENTER to switch to sky view.
The location of the satellites from which you are receiving a
signal appears.
Device Care
Before you attempt to replace the battery, carefully read the
instructions in the owner's manual.
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Thoroughly rinse the device with fresh water after exposure to
chlorine, salt water, sunscreen, cosmetics, alcohol, or other
harsh chemicals. Prolonged exposure to these substances can
damage the case.
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Always wipe the device dry after cleaning or use, and store it in
a cool, dry place.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Cleaning the Device
1
Wipe the device using a cloth dampened with a mild
detergent solution.
2
Wipe it dry.
After cleaning, allow the device to dry completely.
TIP: For more information, go to www.garmin.com/fitandcare.
Data Management
NOTE: The device is not compatible with Windows
Windows NT , and Mac OS 10.3 and earlier.
® ®
Connecting the Device to Your Computer
You can use the Foretrex device as a USB mass storage device
by connecting it to your computer with a USB cable.
1 Turn the D-ring counter-clockwise, and pull up to open the
rear cover.
2
Plug the small end of the USB cable into the USB port on the
device.
3
Plug the large end of the USB cable into a computer USB
port.
4
Select YES to enter mass storage mode.
Your device appears as a removable drive in My Computer
on Windows computers and as a mounted volume on Mac
computers.
8
NOTICE
® 95, 98, Me,
Transferring Files to Your Device
1 Connect the device to your computer.
On Windows computers, the device appears as a removable
drive or a portable device. On Mac computers, the device
appears as a mounted volume.
NOTE: Some computers with multiple network drives may not
display device drives properly. See your operating system
documentation to learn how to map the drive.
2 On your computer, open the file browser.
3 Select a file.
4 Select Edit > Copy.
5 Open the portable device, drive, or volume for the device.
6
Browse to a folder.
7
Select Edit > Paste.
The file appears in the list of files in the device memory.
Deleting Files
If you do not know the purpose of a file, do not delete it. Your
device memory contains important system files that should not
be deleted.
1
Open the Garmin drive or volume.
2 If necessary, open a folder or volume.
3 Select a file.
4 Press the Delete key on your keyboard.
NOTE: If you are using an Apple
the Trash folder to completely remove the files.
Disconnecting the USB Cable
If your device is connected to your computer as a removable
drive or volume, you must safely disconnect your device from
your computer to avoid data loss. If your device is connected to
your Windows computer as a portable device, it is not necessary
to safely disconnect the device.
1
Complete an action:
• For Windows computers, select the Safely Remove
Hardware icon in the system tray, and select your device.
• For Apple computers, select the device, and select File >
Eject.
2
Disconnect the cable from your computer.
Receiving Data Wirelessly
Before you can receive data wirelessly, you must be within 3 m
(10 ft.) of a compatible Garmin device.
Your device can receive waypoints and routes when connected
with a compatible Garmin device.
From the menu page, select CONNECT > RECEIVE
WIRELESSLY.
When a compatible Garmin device is found, the status
changes from CONNECTING to RECEIVING DATA. When
data is received, the status changes to TRANSFER
COMPLETE.
Sending a Route Wirelessly
Before you can send a route wirelessly, you must be within 3 m
(10 ft.) of a compatible Garmin device.
1 From the menu page, select ROUTES > LIST ALL.
2 Select a route.
3 Select SEND.
Sending a Waypoint Wirelessly
Before you can send a waypoint wirelessly, you must be within
3 m (10 ft.) of a compatible Garmin device.
1
From the menu page, select WAYPOINTS > LIST ALL.
NOTICE
computer, you must empty
®
Device Information