1. Manuals
  2. Brands
  3. Planet Manuals
  4. Switch
  5. POE-400
  6. User manual

Planet POE-400 User Manual

Ieee 802.3af 4-port power over ethernet injector hub
Hide thumbs Also See for POE-400:
Table of Contents

Advertisement

Quick Links

Download this manual
IEEE 802.3af
4-Port Power over Ethernet Injector Hub
POE-400
User's Manual
- 1 -

Advertisement

Table of Contents
loading

Related Manuals for Planet POE-400

Summary of Contents for Planet POE-400

  • Page 1 IEEE 802.3af 4-Port Power over Ethernet Injector Hub POE-400 User’s Manual - 1 -...

  • Page 2: Fcc Warning

    Trademarks Copyright © PLANET Technology Corp. 2006. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.

  • Page 3: Table Of Contents

    ... 5 RODUCT UTLOOK 2. HARDWARE INSTALLATION... 6 2.1. Before Installation... 6 2.2 POE-400 and POE-152S, the IEEE 802.3af Injector / Splitter and equipment installation ... 7 3. TROUBLESHOOTING ... 8 APPENDIX A NETWORKING CONNECTION... 9 A.1 S ‘ RJ-45 P...

  • Page 4: Introduction

    Supporting power supply of 70 watts, POE-400 provides sufficient power to the 4 remote devices. There are 8 RJ-45 STP ports on POE-400. Half of the ports on right panel function as "Data" and the other half on left panel function as "Data and Power". Each of the "Data and Power" port as an injector which inserts DC Voltage into the CAT 5 cable allowing the cable between the Injector and Splitter to transfer data and power simultaneously.

  • Page 5: Specification

    220g FCC Class B, CE mark IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3af Power over Ethernet Function Lights to indicate that the POE-400 has power. Lights to indicate the port is providing 48VDC in-line power. - 5 -...

  • Page 6: Hardware Installation

    POE-400 can provide you a way to supply power for this Ethernet device conveniently and easily. The POE-400 equips with an AC-DC adapter with DC 48V input and injects this DC power into the pin of the twisted pair cable (pair 4, 5 and pair 7, 8).

  • Page 7: Poe-400 And Poe-152S, The Ieee 802.3Af Injector / Splitter And Equipment Installation

    2.2 POE-400 and POE-152S, the IEEE 802.3af Injector / Splitter and equipment installation For the places hard to find the power inlet, the POE-400 provide the easiest way to power your Ethernet devices such as PLANET IEEE 802.3af Power over Ethernet Splitter( POE-152S) with Internet Camera (ICA-210 ) or Wireless Access Point (WAP-4060PE) installed in the small office.

  • Page 8: Troubleshooting

    Why I connect my PoE device to POE-400 and it cannot power on? Solution: Please check the cable type of the connection from POE-400 to the other end. The cable should be an 8-wire UTP, Category 5/5e, EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100 meters, all will affect the power supply.

  • Page 9: Appendix A Networking Connection

    A.1 Switch‘s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment Contact Media Dependant Interface Tx + (transmit) Tx - (transmit) Rx + (receive) 4, 5 IEEE 802.3af DC 48V Rx - (receive) 7, 8 A.2 RJ-45 cable pin assignment The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.

Table of Contents