Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Planet FSD-1600
Summary of Contents for Planet FSD-1600
-
Page 2: Ce Mark Warning
Trademarks Copyright PLANET Technology Corp. 2004 PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Contents in this docu- ment are subject to revision without prior notice. FCC Class A Appliance This equipment generates and uses radio frequency energy. -
Page 3: Table Of Contents
1.1 Checklist 1.2 Introduction 1.3 Features Chapter 2 Hardware Description 2.1 Front Panel 2.1.1 FSD-800/FSD-801 2.1.2 FSD-1600/FSD-1601 2.2 Rear Panel 2.3 Hardware Installation Chapter 3 Configuration and Application 3.1 The Switch Operation 3.2 The Smart Function (16-port model) 3.2.1 TP or Fiber-optic selection (for FSD-1601 only) 3.2.2 Port-based VLAN... -
Page 4: Chapter 1 General Introduction
This Switch is a highly reliable network switch and is the ideal device for bridging Ethernet to Fast Ethernet workgroups or networks. Simple and cost-effective, the Switch complies to IEEE802.3u, IEEE802.3, 100Base-TX, and 10Base-T. -
Page 5: Features
• Runt and CRC Filtering eliminates erroneous packets to optimize the network bandwidth • Provide internal power supply • LED indicators for simple diagnostics and management • Auto- MDI and MDI-X detect for easily connecting to PC or hub/Switch uplink • DIP Switch for smart function (16-port model only) -
Page 6: Chapter 2 Hardware Description
LED indicators. Before connecting any network device to the hub, read this chapter carefully. 2.1 Front Panel The unit front panel provides a simple interface monitoring the Switch. It includes a power indicator for each port. 2.1.1 FSD-800/FSD-801... -
Page 7: Fsd-1600/Fsd-1601
The port is operating in half-duplex mode. check the opposite end is using the same transmit mode before make the connection. If you want to adjust the DIP NOTE: switch, please power off FSD-801 first. 2.1.2 FSD-1600/FSD-1601 Figure 2-2 Front Panel of FSD-1600/ FSD-1601... -
Page 8: Rear Panel
Fiber-optic port can operate in one time. 2.2 Rear Panel There is one power socket on the back of the switch, 100~240VAC, 50/60Hz. And one more DIP-switch for FSD-1600 and FSD-1601 for smart function. Figure 2-3 Rear Panel of the FSD-800/801... - Page 9 DIP Switch (Smart function for FSD-1600/1601) Function TP / FX Selection Fiber Full/Half duplex Switch VLAN topology type selection Port Based VLAN Port Trunk 0 (port 1,2,3,4) Port Trunk 1 (port 5,6,7,8) Port Trunk 2 (port 9,10,11,12) Port Trunk 3...
-
Page 10: Hardware Installation
2. Connect the output cord of power supply to the AC inlet. 3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP cabling. 4. Connect another hub or PC to the other port of Switch by following the same process as described in Step 3. Notice:... -
Page 11: Chapter 3 Configuration And Application
Chapter 3 Configuration and Application This chapter shows you how the Switch works, and how to install the Switch and also to configure the smart functions provided in the 16-port model. 3.1 The Switch Operation Address Table The Switch is implemented with an address table. This address table composed of many entries. -
Page 12: The Smart Function (16-Port Model)
*100Mbps, no auto-negotiation *100Mbps, with auto-negotiation 3.2 The Smart Function (16-port model) The FSD-1600 and FSD-1601 is with one DIP switch on the rear of the switch, these ON/ OFF switches provides the functions as below: • Twisted Pair or Fiber-optic selection •... -
Page 13: Port-Based Vlan
Related DIP: 3, 4 Default meaning: No VLAN setting. VLAN can be used to separate ports into different groups in the same switch. This will secure port from being accessed by other ports on the switch. DIP 4: Turns on will enable the port-based VLAN capability DIP 3: The two positions represent two different VLAN choices: OFF:There are 14 VLANs. -
Page 14: Port-Based Priority
3.3.1 Basic 100Mbps Server, PCs to 10/100Mbps Switch Plug one end of the Category 5 UTP Cable into any one port of the Switch, and the other end of this cable into the RJ-45 of Fast Ethernet Adapter in the server or PC. The cable length between these 2 connecting points should not exceed 100 meters. -
Page 15: Connect To 100Base-Fx Switch/Device (Model: Fsd-801/1601)
412 meters. For Switch or end-node that works on full-duplex mode, the maximum distance cannot exceed 2 kilometers. The pair of the connectors must be crossed, ie. TX/RX port of the Switch should connect to RX/TX Port of the device in other end. -
Page 16: Set Up The Workgroup And Uplink To The Backbone (Model: Fsd- 1600/1601)
Figure 3-3 Connection with VLAN enable Turn on the DIP 4, the FSD-1600 soon separate the fourteen ports (Port 1 to Port 14) into different group, then you can install two file servers to port 15, port 16, those fourteen users shall not see each other where they can freely access the information from the two file server. -
Page 17: Chapter 4 Troubleshooting
Performance is bad Solution: Check the full duplex status of the Ethernet Switch. If the Ethernet Switch is set to full duplex and the partner is set to half duplex, then the performance will be poor. Some stations can not talk to other stations located on the other port Solution: The address table may contain older information than of the address table of that node. -
Page 18: Appendix A Specifications
IEEE 802.3 10Base-T EthernetIEEE 802.3u 100 Base-TX and Standards: 100Base-FX Fast EthernetIEEE 802.3x Flow control Protocol: CSMA/CD Ethernet: Data Transfer 10Mbps(half duplex) / 20Mbps (full duplex) Fast Ethernet: Rate: 100Mbps (half duplex) / 200Mbps (full duplex) Topology: Star • 10Base-T:2-pair UTP Cat. 3,4, 5 (100 m, max.)EIA/TIA- 568 100-ohm STP (100 m, max.) •... - Page 19 FCC Class A, CE Mark Class A Transmission Store-and-forward Method Filtering Address 1/8K entries Table Packet Filtering/ 14,880pps per port (for 10Mbps) Forwarding Rate 148,800pps per port (for 100Mbps) MAC Address Automatic update / Max age: fixed Learning Performance...
-
Page 20: Appendix B Rj-45 Pin Specification
When connecting your FSD-series 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a modified crossover cable is not necessary. Each port of the Switch is auto-MDI detection. That means you can direct connect the Switch to any Ethernet devices with a Category 5, UTP straight wire. - Page 21 This page is intentionally left blank...
- Page 23 Part No.: 2010-000004-003...