Optional remote control and DV Prompter manual ..........12 Adjusting the lower rail of the prompter frame ............13 Cleaning the 60/40 Glass ..................14 Optional HC-300 Hard Case ..................15 HC-300 Features .....................15 HC-300 specifications ....................15 Specifications TP-300 ....................16 Service and Support ....................17...
SERVICE AND SUPPORT ............................... 21 Disclaimer of Product and Services The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete.
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.
• The product warranty period beings on the purchase registered with Datavideo within 30 days of purchase. date. If the purchase date is unknown, the product • Certain parts with limited lifetime expectancy such as...
• The product warranty period begins on the purchase registered with Datavideo within 30 days of purchase. date. If the purchase date is unknown, the product • Certain parts with limited lifetime expectancy such as...
Camera Riser Screw Short with two washers and nut Instruction Manual NOTE: Depending on your order, your TP-300 kit could have been supplied with one of a range of wired or Bluetooth remote controls – for more information on the remote controls please speak with your local Datavideo supplier or check our website www.datavideo.info for details.
Camera Riser Screw Short with two washers and nut Instruction Manual NOTE: Depending on your order, your TP-300 kit could have been supplied with one of a range of wired or Bluetooth remote controls – for more information on the remote controls please speak with your local Datavideo supplier or check our website www.datavideo.info for details.
(not supplied) into a low cost and effective prompter. The Datavideo Prompter Kit, TP-300, can be used in either a theatre setting, or a video studio. Prepared scripts or cue sheets can be easily copied and pasted into the DV...
(not supplied) into a low cost and effective prompter. The Datavideo Prompter Kit, TP-300, can be used in either a theatre setting, or a video studio. Prepared scripts or cue sheets can be easily copied and pasted into the DV...
PROMPTER KIT FOR TABLET TP-300 Assembly – Normal tripod set up 1. Attach/screw the tripod camera quick release plate to the screw holes on the base of the prompter frame, item A. If necessary use the adaptor screw, item C.
PROMPTER KIT FOR TABLET TP-300 Assembly – Normal tripod set up 1. Attach/screw the tripod camera quick release plate to the screw holes on the base of the prompter frame, item A. If necessary use the adaptor screw, item C.
Page 8
PROMPTER KIT FOR TABLET TP-300 Guide/slide 60/40 Glass sheet, item I, into the Glass frame, item F. The Red circle sticker on the glass should be facing camera position / lens. The Green circle sticker on the glass should be facing toward the on screen talent / commentator.
Page 8
PROMPTER KIT FOR TABLET TP-300 Guide/slide 60/40 Glass sheet, item I, into the Glass frame, item F. The Red circle sticker on the glass should be facing camera position / lens. The Green circle sticker on the glass should be facing toward the on screen talent / commentator.
Page 9
PROMPTER KIT FOR TABLET TP-300 Decide if camera riser blocks, item K, are required depending on the position of the camera lens. If using 1 block use the short hex screws, item M, through one block but leave the centre hole empty. Turn the block over so that screws project downwards and sit in the long slot on top of the prompter frame, item A.
Page 9
PROMPTER KIT FOR TABLET TP-300 Decide if camera riser blocks, item K, are required depending on the position of the camera lens. If using 1 block, use the short hex screws, item M, through one block but leave the centre hole empty. Turn the block over so that screws project downwards and sit in the long slot on top of the prompter frame, item A.
Page 10
PROMPTER KIT FOR TABLET TP-300 10. Pull the draw cord to secure the black camera Snood / Hood around the camera lens and to shut out light from camera side. 11. Fit the adjustable mounting bracket, item E, to the...
Page 10
PROMPTER KIT FOR TABLET TP-300 10. Pull the draw cord to secure the black camera Snood / Hood around the camera lens and to shut out light from camera side. 11. Fit the adjustable mounting bracket, item E, to the...
PROMPTER KIT FOR TABLET TP-300 Assembly – Below lens set up 1. Attach/screw the tripod camera quick release plate to the screw holes on the base of the prompter frame, item A. If necessary use the adaptor screw, item C. Slide and secure the tripod plate, with prompter frame on top, onto the head of tripod.
PROMPTER KIT FOR TABLET TP-300 Assembly – Below lens set up 1. Attach/screw the tripod camera quick release plate to the screw holes on the base of the prompter frame, item A. If necessary use the adaptor screw, item C. Slide and secure the tripod plate, with prompter frame on top, onto the head of tripod.
Consult your camera manual for further help and advice with its exposure and white balance settings. Using the Riser Blocks When using this TP-300 Prompter Kit you may need to use one or both riser blocks to raise the camera up so that the camera lens is positioned vertically as near to the middle of the 60/40 Glass as possible.
Consult your camera manual for further help and advice with its exposure and white balance settings. Using the Riser Blocks When using this TP-300 Prompter Kit you may need to use one or both riser blocks to raise the camera up so that the camera lens is positioned vertically as near to the middle of the 60/40 Glass as possible.
There is another manual which covers how to use the remote control and also the DV Prompter application. It is supplied with the remote control and can also be downloaded as a PDF document from your local Datavideo office website.
See the following section, Optional Bluetooth Teleprompter Remote Control, which covers how to use the remote control. There is also a separate manual supplied with the remote control and can also be downloaded as a PDF document from your local Datavideo office website.
This to move the position of the tablet forwards away from the camera position or backwards towards the camera position. To do this you will need the hex tools provided with the TP-300 kit (Item B on page 5). 1. First carefully dismantle the current TP-300 set up to remove the prompter frame (Item A).
TP-300 Optional Bluetooth Teleprompter Remote Control This WR-500 remote control is designed to be used with Datavideo’s teleprompter products, DV Prompter and DVP-100. DV Prompter app is a FREE download from the Apple app store for iOS devices and also from Google Play for Android devices.
Datavideo recommend cleaning the glass regularly to remove dust and finger print marks. This will ensure the best image quality is recorded when the camera is looking through the glass.
PROMPTER KIT FOR TABLET TP-300 Select and start the required script within the DV Prompter app. To switch the remote into Bluetooth pairing mode press and hold the centre Play / Pause button for 3 to 4 seconds. GREEN LED will now blink on / off repeatedly to indicate it is ready to pair with a Bluetooth device.
The foam packaging of the TP-300 kit has been designed so that customers who buy the optional hard case can simply lift the foam out from the retail carton of the TP-300 and insert it directly into the optional HC-300 hard case.
PROMPTER KIT FOR TABLET TP-300 Control Buttons Whilst Whilst Button scrolling text text paused Speed up text scroll Next Break Marker Slow down text scroll Previous Break Marker Pause text Play text Reduce font size Load previous script Increase font size...
PROMPTER KIT FOR TABLET TP-300 This button battery can be replaced by the user when it dies. Please remove the back case cover carefully to avoid user damage to the PCB or case. Then slide the old battery out. Please ensure the new button battery is installed with the positive (+) side of the cell facing the (+) sign on the...
Service & Support It is our goal to make owning and using Datavideo products a satisfying experience. Our support staff is available to assist you to set up and operate your system. Contact your local office for specific support requests. Plus, DATAVIDEO WORLDWIDE OFFICES please visit www.datavideo.com to access our FAQ section.
To do this you will need the hex tools provided with the TP-300 kit (Item B on page 6). First carefully dismantle the current TP-300 set up to remove the prompter frame (Item A).