Planet ADW-4401 A/B User Manual
  1. Manuals
  2. Brands
  3. Planet Manuals
  4. Network Router
  5. ADW-4401 A/B
  6. User manual

Planet ADW-4401 A/B User Manual

802.11g wireless adsl 2/2+ router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
802.11g Wireless
ADSL 2/2+ Router
ADW-4401 A/B
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Planet ADW-4401 A/B

Summary of Contents for Planet ADW-4401 A/B

  • Page 1 802.11g Wireless ADSL 2/2+ Router ADW-4401 A/B User's Manual...
  • Page 2 Copyright Copyright© 2006 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
  • Page 3 FCC Caution: To assure continued compliance (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
  • Page 4 Safety This equipment is designed with the utm and use it. However, special and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

  • Page 5: Table Of Contents

    . INTRODUCTION ...7 1.1 FEATURE...7 1.2 PACKAGE CONTENT 1.3 PHYSICAL DETAILS ...9 2. INSTALLATION ...11 2.1 SYSTEM REQUIREMENT ...11 2.2 HARDWARE INSTALLATION ...11 3 CONFIGURATION...13 3.1 DETERMINE YOUR CONNECTION SETTINGS ...13 3.2 CONNECTING THE ADSL ROUTER TO YOUR NETWORK...13 3.3 CONFIGURING WITH WEB BROWSER ...13 3.3.1 QUICK SETUP GUIDE ...14 3.3.2 System Time ...18 3.3.3 Admin Setting...19...
  • Page 6 3.9.4 ADSL Type Setting ...32 3.10.1 Static Routing ...32 3.10.2 Dynamic Routing...33 3.10.3 Routing Table ...34 3.11.1 System Status...35 Append ix A: Glossary...36...

  • Page 7: Introduction

    1. Introduction The PLANET 802.11g Wireless ADSL 2/2+ Router, ADW-4401, provides office and residential users the ideal solution f Internet connection on a 5 4Mbps wireless network and a 10/100Mbps Fast Ethernet backbone. It can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 3.5Mbps.
  • Page 8 Fixed or Dynamic IP Address. On the Internet (WAN port) connection, ADW-4401 supports both Dynamic IP Address (IP Address is allocated on connection) and Fixed IP Address. an ed Internet Functions Virtual Servers. This feature allows Internet users to access Internet server on your LAN.

  • Page 9: Package Contents

    4-Port Switch. The ADW-4401 incorporates a 4-port 10/100Base-TX switching hub, making it easy to create or extend your LAN. DHCP Server Support. Dynamic Host Configuratio n Protocol provides a dynamic IP address to PCs and othe can act as a DHCP Server for devices on your local LAN and WLAN. 1.2 Pa ckage Contents ‧...
  • Page 10 WLAN Flashing When wireless AP is ready Link Flashing TX or RX activity No Link These four LAN (Local Area Network) ports are where you will connect networked devices, such as PCs, print servers remote hard drives, and anything else you want to put on your network Rear Panel Rear panel Port and Button Definition...

  • Page 11: Installation

    2. Installation This chapter offers infor mation about installing your router. If you are not familiar with the hardware or software parameters presented here, please consult your service provider for the values needed. .1 System Requirement 1. Personal computer (PC) 2.
  • Page 12 Step 3. Connect the Power Adapter to the Router onnect the power adapter to the port labeled POWER on the rear panel of router. Step 4. Connect All Cables to the Network he procedure for connecting cables differs depending on whether or not your telephone equipment is connected to a POTS s plitter.

  • Page 13: Configuration

    3 Configuration 3.1 Determine your connection settings Before you configure the router, you need to know the connection information supplied by your ADSL service provider. .2 Connecting the ADSL Router to your network Unlike a simple hub or switch, the setup of the ADSL Router co nsists of more than simply plugging everything together.

  • Page 14: Quick Setup Guide

    3.3.1 Quick Setup Guide You can use "Quick Setup" to setup the router as follows, and the router will connect to the Internet via ADSL line.
  • Page 15 Click "Quick Start" to get into the quick setup procedures. Click "RUN WIZARD" to start up this procedure. Step 1 - Click "Next" to setup your new administrator's password.
  • Page 16 Step 2 - Click "Next" to setup your time zone. Step 3 - Click "Next" to setup your Internet connection type. You can have this information from your Internet Service Provider.
  • Page 17 Enter the connection information provided by your ISP.

  • Page 18: System Time

    3.3.2 System Time Go to Maintenance->Time Zone and select system time as you wish.

  • Page 19: Admin Setting

    Connecting to a Simple Network Time Protocol (SNTP) server allows the router to synchronize the system clock to the global Internet. The synchronized clock in the router is used to record the security log and control client filtering. 3.3.3 Admin Setting Go to Maintenance->...

  • Page 20: Firmware Update

    3.3.4 Firmware Update Go to Maintenance -> Firmware to upgrade the firmware. The new firmware for your router can improve functionality and performance. Enter the path and name of the upgrade file then click the UPGRADE button below. You will be prompted to confirm the upgrade. 3.3.5 System Log Go to Status ->...

  • Page 21: System Reset

    3.3.6 System Reset In the event that the router stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, select "Current Setting" and click on the "RESTART" button below.

  • Page 22: Adsl Status

    3.4.1 ADSL Status Go to Status->Device Info. The 'ADSL Line Status' enables you to check the status of your ADSL connection including how fast data is being transferred. 3.4.2 ADSL Statistics Go to Status-> Statistics and select ADSL interface. You can see the traffic Statistics of ADSL interface.

  • Page 23: Vc Configuration

    3.4.3 VC Configuration Go to Interface Setup -> Internet. To add or delete ADSL VC configuration, these information provide by ISP. 3.5.1 WAN Configuration Go to Interface Setup -> Internet. The router can be connected to your service provider in any of the following ways. Dynamic IP Address: Obtain an IP address automatically from your service provider.

  • Page 24: Wan Status

    PPPoE: PPP over Ethernet is a common connection method used for xDSL PPPoA: PPP over ATM is a common connection method used for xDSL Bridge: Bridge mode is a common connection method used for xDSL modem. 3.5.2 WAN Status Go to Status -> Device Info and select the Virtual Circuit to see the connection status.

  • Page 25: Dns

    3.5.3 DNS Go to Interface -> LAN to enable DHCP server. Then you can set DNS server for the router. A Domain Name system (DNS) server is like an index of IP addresses and Web addresses. If you type a Web address into you browser, a DNS server will find that name in its index and find the matching IP address.

  • Page 26: Ddns

    3.5.4 DDNS Go to Access Management -> DDNS to setup your DDNS parameters. Dynamic DNS allows you to update your dynamic IP address with one or many dynamic DNS services. So anyone can access your FTP or Web service on your computer using DNS-like address.

  • Page 27: Lan Configuration

    3.6.1 LAN Configuration Go to Interface Setup -> LAN. The 'LAN Settings' option enables you to configure the LAN port. If the DHCP Relay is selected, the DHCP requests from local PCs are forward to the DHCP server runs on WAN side. To have this function working properly, disable the NAT to run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry.

  • Page 28: Wireless Security

    3.7.2 Wireless Security Go to Interface -> Wireless to setup the wireless security. The Authentication type supports “shared key WEP 64bits", "shared key WEP 128bits”, “WPA-PSK”.

  • Page 29: Ip Filtering

    3.8.1 IP Filtering Go to Access Management -> IP Filtering to block some packets form WAN. The router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. “Block WAN Scan”...

  • Page 30: Nat Setting

    3.9.1 NAT Setting Go to Advanced Setup->NAT to setup the NAT features. Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single public IP address or multiple public IP addresses. NAT can also prevent hacker attacks by mapping local addresses to public addresses for key services such as the Web or FTP.

  • Page 31: Virtual Server

    3.9.2 Virtual Server Go to Advanced Setup ->NAT -> Virtual Server to set virtual server as you need. (known as Port Mapping). You can configure the router as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses.

  • Page 32: Adsl Type Setting

    3.9.4 ADSL Type Setting Go to Advanced Setup ->ADSL to set different ADSL connection If you meet an ADSL connection problem, you can select a different ADSL connection type to get more fast connection. 3.10.1 Static Routing Go to Advance Setup -> Routing ->Add to setup static route features. The static routing function determines the path that router follows over your network before and after it passes through your router.

  • Page 33: Dynamic Routing

    3.10.2 Dynamic Routing Go to Interface Setup -> Internet to select Dynamic Route as you need. The dynamic routing feature of the router can be used to allow the router to automatically adjust to physical changes in the network's layout. The router uses the dynamic RIP protocol.

  • Page 34: Routing Table

    3.10.3 Routing Table Go to Advance Management -> Routing to see the Routing Table. The Routing table allows you to see how many routings on your routing table and interface information...

  • Page 35: System Status

    3.11.1 System Status Go to Status -> Device Info to see the router's information. The System Status page shows the WAN, LAN and the router's firmware version.

  • Page 36: Appendix A: Glossary

    Appendix A: Glossary Address mask A bit mask select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the network portion of the Internet address and one or more bits of the local portion. Sometimes it called subnet mask. AAL5 ATM Adaptation Layer - This layer maps higher layer user data into ATM cells, making the data suitable for transport through the ATM network.
  • Page 37 Central Office. Refers to equipment located at a Telco or service provider's office. Customer Premises Equipment located in a user's premises DHCP (Dynamic Host Configuration Protocol) DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network. DHCP eliminates having to manually assign permanent IP addresses to every device on your network.
  • Page 38 transmission rate of 10 Mbps. File Transfer Protocol. The Internet protocol (and program) transfer files between hosts. Hop count A measure of distance between two points on the Internet. It is equivalent to the number of gateways that separate the source and destination. HTML Hypertext Markup Language - The page-coding language for the World Wide Web.
  • Page 39 IP address The 32-bit address assigned to hosts that want to participate in a TCP/IP Internet. Internet service provider - A company allows home and corporate users to connect to the Internet. Media Access Control Layer - A sub-layer of the Data Link Layer (Layer 2) of the ISO OSI Model responsible for media control.
  • Page 40 PPPoE PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. Remote server A network computer allows a user to log on to the network from a distant location. Request for Comments - Refers to documents published by the Internet Engineering Task Force (IETF) proposing standard protocols and procedures for the Internet.
  • Page 41 (2) IBM term for software interfaces that allow two UNIX application programs to talk via TCP/IP protocols. Spanning-Tree Bridge Protocol (STP) Spanning-Tree Bridge Protocol (STP) - Part of an IEEE standard. A mechanism for detecting and preventing loops from occurring in a multi-bridged environment. When three or more LAN's segments are connected via bridges, a loop can occur.
  • Page 42 Telnet The virtual terminal protocol in the Internet suite of protocols - Allows users of one host to log into a remote host and act as normal terminal users of that host. Transparent bridging The intelligence necessary to make relaying decisions exists in the bridge itself and is thus transparent to the communicating workstations.

This manual is also suitable for:

Adw-4401a/b

Table of Contents