Speaker Distance; Bass Peak Level; X-Curve - Pioneer VSX-2016AV Operating Instructions Manual

The System Setup menu
Tip
• You can change the channel levels at any time by
pressing CH LEVEL then using
control.

Speaker Distance

For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
1 Select 'Speaker Distance' from the Manual SP Setup
menu.
5.Manual SP Setup
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
:Return
2 Adjust the distance of each speaker using the
buttons.
You can adjust the distance of each speaker in 0.1 meter
increments.
3 When you're finished, press RETURN .
You will return to the Manual SP Setup menu.
Tip
• For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.

Bass Peak Level

Some audio sources (for example, Dolby Digital and DTS)
include ultra-low bass tones. Set the bass limiter as
needed to prevent the bass from distorting the sound.
1 Select 'Bass Peak Level' from the Manual SP Setup
menu.
The current setting is displayed. When OFF is displayed
the attenuator is off (bass output is not affected).
5.Manual SP Setup
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
:Return
Note
1 If the YES or PLUS setting on the subwoofer is selected (in Speaker Setting on page 45), the test tone will only play back from the subwoofer. If not, the
test tone will play back from the front and surround speakers set to LARGE.
2 Since the principal is the same, X-Curve isn't applied when you're using any of the Home THX modes (see Using the Home THX modes on page 27).
on the remote
5c.Speaker Distance
L 3.0 m
C [ 3.0 m ]
R [ 3.0 m ]
SR [ 3.0 m ]
SBR [ 3.0 m ]
SBL [ 3.0 m ]
SL [ 3.0 m ]
SW [ 3.0 m ]
:Finish
5d.Bass Peak Level
Bass Peak Level :OFF
[Setting Start ]
[Setting Clear ]
:Return
2 Select a setup option.
5d.Bass Peak Level
Bass Peak Level
[Setting Start
[Setting Clear
Enter:Setting Start
• Setting Start – The volume is set to –60 dB, a test
tone plays back and you make the setting.
• Setting Clear – Clears any previous setting and
switches limiting off.
3 If you selected ' Setting Start' , use
the test tones and specify the bass peak level then press
ENTER .
5d.Bass Peak Level
Bass Peak Level
Increase the Bass
Peak Level to
a comfortable volume
(-80dB = no sound)
ENTER:Finish
Set the bass peak level gradually, then press ENTER at
the point just before the tone starts to distort.
display on the receiver shows RESUME while the volume
returns to its original position, then you automatically
return to the main Bass Peak Level menu.
4 When you're finished, press RETURN .
You will return to the Manual SP Setup menu.

X-Curve

Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
2
soundtracks.
1 Select 'X-Curve' from the Manual SP Setup menu.
5.Manual SP Setup
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
:Return
:OFF
]
]
:Return
to adjust
-60dB
:Cancel
1
The
5e.X-Curve
X-Curve -2.0dB/oct
:Finish
08
47
En