SERVICE MANUAL DVD DIGITAL CINEMA SYSTEM MB427 2005 TH-C9 Area suffix US ------------------------ Singapore UT ---------------------------- Taiwan UX -------------------- Saudi Arabia UG --- Turkey,South Africa,Egypt UN ----------------------------- Asean (SP-THC9F) (SP-THC9S) (SP-THC9F) (SP-THC9C) (SP-PWC9) (XV-THC9) Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS PRECAUTION.
Page 2
SPECIFICATION Center unit-XV-THC9 Audio section Total Harmonic Distortion *1 0.02% Digital input*2 DIGITAL IN (DBS): -21 dBm to -15 dBm (OPTICAL): (660 nm ±30 nm) Video section Video System PAL/NTSC Horizontal Resolution 500 lines Signal-to-Noise Ratio 64 dB Composite: 1.0 V(p-p)/75 Ω Video output level S-video-Y: 1.0 V(p-p)/75 Ω...
Page 3
Satellite Speaker-SP-XTHC9 10.0 cm × 2 Front speakers (SP-THC9F) Speaker unit Woofer 10.0 cm × 2 Midrange Tweeter 4 cm Bass-reflex, Magnetically Shielded Power Handling Capacity 140 W 4 Ω Impedance Frequency Range 60 Hz to 20 kHz Dimensions (W × H × D) 270 mm ×...
SECTION 1 PRECAUTION Safety Precautions (1) This design of this product contains special hardware and voltmeter. many circuits and components specially for safety purpos- Move the resistor connection to each exposed metal es. For continued protection, no changes should be made part, particularly any exposed metal part having a return to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across...
Page 5
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Page 6
Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam. procedures other than those specified here in may result in 3.CAUTION : There are no serviceable parts inside the hazardous radiation exposure.
SECTION 3 DISASSEMBLY Main body section 3.1.1 Removing the metal cover (See Figs. 1 to 4) (1) From the both sides of the main body, remove the four screws A attaching the metal cover. (See Figs. 1 and 2.) Metal cover (2) From the back side of the main body, remove the three screws B attaching the metal cover.
Page 9
3.1.2 Removing the front panel assembly (See Figs. 5 and 6) • Prior to performing the following procedures, remove the metal cover. CN457 CN456 Main board (1) From the top side of the main body, disconnect the parallel wires from the connectors (CN456, CN457) on the main board.
Page 10
3.1.3 Removing the DVD changer mechanism assembly (See Fig. 7) • Prior to performing the following procedures, remove metal cover and front panel assembly. DVD changer mechanism assembly (1) From the top side of the main body, remove the screw E at- CN402 CN401 CN403 taching the wire protection board to the main board.
Page 11
3.1.5 Removing the audio & digital input board (See Figs. 9 and 10) • Prior to performing the following procedures, remove the metal cover. Main board CN412 Power supply board (1) From the top side of the main body, disconnect the card wires from the connectors (CN411, CN412) on the main Card wires CN411...
Page 12
3.1.8 Removing the main board (See Fig. 11) • Prior to performing the following procedures, remove the metal cover, rear panel, audio & digital input board and tuner. Wire protection board CN460 CN456 (1) From the top side of the main body, remove the screw R at- CN457 CN401 CN402...
Page 13
Front panel assembly section • Prior to performing the following procedures, remove the front panel assembly from the main body. (See "Removing the front panel assembly") 3.2.1 Removing the phone jack board (See Fig. 1) (1) From the inside of the front panel assembly, remove the screw A attaching the phone jack board.
Page 14
3.2.5 Removing the front board (See Figs. 3 and 4) • Prior to performing the following procedures, remove the phone jack board, bracket board and operation board. Front panel assembly (1) From the front side of the front panel assembly, pull out the volume knob in the direction of the arrow.
Page 15
DVD changer mechanism assembly section Remove the DVD changer mechanism assembly from the main body. (See "Removing the DVD changer mechanism assembly".) 3.3.1 Removing the tray assemblies (See Figs.1 to 5) (1) From the top side of the main body, remove the two screws Top cover A from the top cover and release the two joints a on the both sides of the DVD changer mechanism assembly.
Page 16
Open det. lever Fig.3 Side(R) assembly Tray assemblies Fig.4 Tray assembly Fig.5 1-16 (No.MB427)
Page 17
3.3.2 Removing the DVD servo board (See Figs.6 to 8) Caution: Solder the short land sections d on the DVD pickup before dis- connecting the card wire extending from the DVD pickup. If you do not follow this instruction, the DVD pickup may be dam- DVD pickup aged.
Page 18
3.3.4 Removing the motor board (See Figs.9 and 10) (1) From the top side of the DVD changer mechanism assem- bly, remove the two belts from the motor pulleys. (See Fig.9.) Note: Take care not to attach grease on the belt. Belt Belt (2) Remove the two screws D attaching the motors to the load-...
Page 19
3.3.6 Removing the DVD traverse mechanism assembly (See Fig.11) • Remove the tray assemblies and DVD servo board. DVD changer mechanism assembly (1) From the bottom side of the DVD changer mechanism as- sembly, remove the three screws F attaching the DVD traverse mechanism assembly.
Page 20
3.3.7 Removing the DVD pickup (See Figs.12 to 14) • Remove the tray assemblies, DVD servo board and DVD DVD traverse mechanism assembly traverse mechanism assembly. Feed bracket (1) From the top side of the DVD traverse mechanism assem- Thrust spring bly, release the lock of the connector on the DVD pickup Connector and disconnect the card wire in the direction of the arrow.
Page 21
DVD pickup Rack arm Guide shaft Rack arm spring Fig.14 Connector DVD pickup Screw shaft gear Fig.15 (No.MB427)1-21...
Page 22
3.3.9 Removing the spindle motor board (See Figs.16 and 17) • Remove the tray assemblies, DVD servo board and DVD DVD traverse mechanism assembly traverse mechanism assembly. (1) From the top side of the DVD traverse mechanism assem- Spindle motor board bly, remove the wires from the soldered sections r on the spindle motor board.
3.3.10 Removing the feed motor (See Figs.18 and 19) • Remove the tray assemblies and DVD traverse mechanism Feed bracket assembly. (1) From the top side of the DVD traverse mechanism assem- Thrust spring bly, remove the screw K attaching the feed bracket and re- move the feed bracket from the sections t.
Page 24
3.3.11 Removing the side (L) and tray switch board (See Figs.20 to 22) • Remove the tray assemblies. SIde(L) (1) From the topside of the DVD changer mechanism assem- bly, remove the two screws M attaching the side (L). (See Fig.20.) (2) From the left side of the DVD changer mechanism assem- bly, disconnect the connector...
Page 25
3.3.12 Removing the side (R) assembly (See Fig.23 to 27) • Remove the tray assemblies and DVD servo board. Elevator spring (1) From the inside of the side (R) assembly, release the two tabs aa of the gear cover and remove the gear cover out- ward.
Page 26
3.3.13 Removing the lifter assembly (See Figs.28 to 32) • Remove the tray assemblies, DVD servo board, side (L) and Hook side (R) assembly. (1) (1) From the top side of the DVD changer mechanism as- sembly, turn the gear 1 clockwise to move the lifter assem- bly upward.
Page 27
3.3.14 Removing the sensor board and SV resistor (See Fig.33) • Remove the tray assemblies, side (L), side (R) assembly and Sensor board lifter assembly. (1) Remove the solders from the soldered sections aj on the sensor board and remove the wires. (2) Remove the two screws Q and take out the sensor board with the SV resistor.
3.3.15 Taking out the disc in the play mode (See Fig.34 to 37) Reference: Tray assembly Refer to "3.3.1 Removing the tray assemblies". (1) From the top side of the DVD changer mechanism assem- bly, remove the top cover. (2) Unlock the tray assemblies and draw out the tray assem- blies toward the front.
Page 29
Tray stopper Main tray Sub tray Fig.36 Tray stopper Fig.37 (No.MB427)1-29...
Page 30
Speaker section 3.4.1 Removing the amplifier assembly (See Figs.1 to 3) (1) From the back side of the speaker main body, remove three screws A attaching the amplifier assembly. (See Fig.1.) (2) From the bottom side of the speaker main body, remove the eight screws B attaching amplifier assembly.
Page 31
3.4.2 Removing the rear panel (See Figs.4 and 5) • Prior to performing the following procedure, remove the ampli- fier assembly. (1) From the back side of the amplifier assembly, remove the six screws C and screw D attaching the rear panel. (See Fig.4.) (2) Take out the rear panel with fan motor backward from the amplifier assembly.
Page 32
3.4.4 Removing the power board (See Figs.7 to 9) • Prior to performing the following procedures, remove the am- plifier assembly and rear panel. CN101 Power cord CN151 Power board (1) From the top side of the amplifier assembly, disconnect the CN103 wires from the connectors (CN103, CN151) on the power board.
Page 33
3.4.5 Removing the relay board (See Fig.10) • Prior to performing the following procedure, remove the ampli- fier assembly. Parallel wire CN352 (1) From the top side of the amplifier assembly, disconnect the Wire clamp parallel wire from the connector CN352 on the relay board.
Page 34
3.4.7 Removing the amplifier board (See Fig.14) • Prior to performing the following procedures, remove the am- plifier assembly, rear panel, power board, relay board and heat Main board sink. (1) From the top side of the amplifier assembly, disconnect the amplifier board from the connectors (CN311, CN312) on the main board.
Page 35
3.4.9 Removing the power transformer (See Fig.16) • Prior to performing the following procedure, remove the ampli- fier assembly. CN102 Trans board (1) From the top side of the amplifier assembly, disconnect the wire from the connector CN102 on the trans board. (2) Remove the parallel wire from the wire clamp.
Page 36
3.4.12 Removing the side panel assembly (See Figs.19 and 20) (1) From right side of the speaker main body, insert the tip of the flat-bladed screwdriver or similar tool into the space be- tween the speaker main body and side panel assembly, and lift the side panel assembly little by little to remove.
Page 37
3.4.13 Removing the speaker (See Figs.21 and 22) • Prior to performing the following procedure, remove the side panel assembly. (1) From right side of the speaker main body, remove the eight screws T attaching the speaker. (See Fig.21.) (2) Take out the speaker from the speaker main body. (3) Disconnect the wires (black and red) from the terminal of the speaker.
SECTION 4 ADJUSTMENT Special mode 4.1.1 Outline The contents in the special mode of operation, and the definition of a key (remote controller or main unit) 4.1.2 Special mode 1.DVD TEST MODE It goes into the TEST mode of DVD. DVD TEST mode is canceled by except DVD source, and POWER OFF.
Page 39
5.FORCED NTSC MODE It is made compulsive NTSC mode. From this, with regards to the input of NTSEL_SW, there is nothing only at the time of 1st power on, and it performs NTSC starting. (Command specification is performed to a module.) A mode clearance is performed by power off.
Page 40
4.1.3 Upgrading of firmware (DVD UPGRADE) The latest firmware for upgrading is updated in "Optical disc CSG" page in JS-net. At the time of service, compare the version of the product and the latest version, and upgrade the old version into the latest version. (1) Press "STANDBY/ON"...
Page 41
DVD TEST MODE Insert the power cord in an outlet while pressing the "POWER" and "PLAY" keys on the main unit simultaneously. It is made POWER ON in test mode, and VERSION is displayed on FL. FL indication TEST bb# TEST bb# The initialization state (The 11th figure) "3"...
Page 42
Press the "MENU" key on the remote controller. Enter to CHECK MODE FL indication FL indication Press the "1" key on the remote controller. CHECK CHECK Starting of DISC & normal play (Play from the started position) FL indication Press the "2" key on the remote controller. Existence of WOBBLE 0 : WOBBLE_NO_CHECK (Un-checking.) 1 : WOBBLE_PRESS_MEDIA (Press)
FL indication Press the "0" key on the remote controller. MONITOR output change 1 : SRV_MONI_CIRC 2 : SRV_MONI_SERVO 3-5 : SRV_MONI_ANALOG 6-7 : SRV_MONI_DRC 8-11 : SRV_MONI_SERVO_JIG 12 : SRV_MONI_DEFAULT FL indication Press the "+10" key on the remote controller. Initialization of the contents of a backup memory Press the "STOP"...
Page 44
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MB427) Printed in Japan...
Page 45
SCHEMATIC DIAGRAMS DVD DIGITAL CINEMA SYSTEM TH-C9 Area suffix US ------------------------ Singapore UT ---------------------------- Taiwan CD-ROM No.SML200508 UX -------------------- Saudi Arabia UG --- Turkey,South Africa,Egypt UN ----------------------------- Asean (SP-THC9F) (SP-THC9C) (SP-THC9F) (SP-THC9S) (SP-PWC9) (XV-THC9) Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Page 46
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety.
Block diagram <Main body section> <Subwoofer section> DVD servo section Audio & Digital input section Amplifier section EXADT0 to 15, EXADR16 to 20 FL-ch SW.P.ON, SETUP A, B, C, D, E, F, RF+, PD(CD), PD(DVD) NEXCE, NEXOE, NEXWE IC509 SYSTEM FR-ch DVD traverse FLASH ROM...
Page 48
Standard schematic diagrams <Main body section> Power supply section GVA10092-A2 T 9 0 1 C 9 5 1 1 0 0 p / 5 0 Q Q S 0 0 9 7 - 0 0 1 Q 9 5 1 POWER PWB C P 9 5 1 E P 9 0 1...
Page 49
System control section TO CN703 TO CN441 (SHEET 5) TO CN702 TO CN442 (SHEET 5) (SHEET 7) TO TUNER (SHEET 7) C N 4 1 1 C N 4 1 2 C N 4 0 2 C N 4 0 1 C N 4 1 0 Q G F 1 0 3 6 C 1 - 3 1 Q G F 1 0 3 6 C 1 - 0 8...
Page 50
Video input/output section GVA10092-A1 V E R . B C 4 4 9 1 0 . 0 1 / 5 0 C 4 4 7 2 3 3 0 p / 5 0 J 4 4 0 3 Q N Z 0 6 2 5 - 0 0 1 R 4 4 7 2 1 5 0 C 4 4 7 6...
Page 51
FL display section GVA10094-A1 FL PWB C 5 1 0 C 5 0 9 D I 5 0 1 Q L F 0 1 5 4 - 0 0 1 FL DISPLAY K 5 0 2 C 5 1 5 0 .
Page 52
Audio & Digital input section GVA10093-A1 AUDIO PWB R 1 1 0 1 C 2 5 0 3 4 7 0 4 . 7 / 5 0 A U X - L L - I N A U X - R C 2 5 0 4 R 1 1 0 2 R - I N...
Page 56
<Subwoofer section> Mother section TO CN112 TO CN302 TO CN304 (SHEET 10) (SHEET 10) (SHEET 10) C N 5 0 1 C N 5 0 2 C N 5 0 3 Q G B 2 5 1 0 K 2 - 1 5 Q G B 2 5 1 0 K 2 - 2 0 Q G B 2 5 1 0 K 2 - 0 6 R 6 0 5...
Page 57
Terminal section K 3 1 0 1 L 3 1 7 1 Q Q R 1 2 7 7 - 0 0 1 Z C 3 1 7 7 Q Q L Z 0 0 5 - R 4 5 2 2 0 P / 5 0 L c h O U T C 3 1 7 4...
Page 58
Amplifier section C L O C K O S C I L L A T O R SYSTEM CONNECTOR S S S _ O N N O T U S E 1 4 1 3 1 2 1 1 1 0 G N D C 1 2 1 1 Q 1 2 1 1...
Page 59
Printed circuit boards <Main body section> Main board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) (Phone jack board) (Wire protection board) (Bracket board) CN701 (Bracket board) W6001 C6004 C6001 K6002 R6001 C6002 (Main board) J4891 C4718...
Page 64
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MB427SCH)
PARTS LIST [ TH-C9 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix US ---------------------- Singapore UT --------------------------- Taiwan UX ------------------- Saudi Arabia UG - Turkey,South Africa,Egypt UN ----------------------------Asean - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1)
Page 66
Exploded view of general assembly and parts list Block No. Operation board Power key board Bracket board...
Page 67
Power supply board Main board Wire protection board Audio & Digital input board Bracket board Bracket board Front board Phone jack board...
Page 68
General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GV10233-002A FRONT PANEL ASSY GV20310-001A FRONT LENS GV30641-002A VOLUME RING QYSDSF2608ZA TAP SCREW M2.6 x 8mm QYSDSF2608ZA TAP SCREW M2.6 x 8mm(x2) QYSDSF2608ZA TAP SCREW M2.6 x 8mm(x4) LV42851-006A FL SCREEN GV20312-001A...
Page 69
Speaker assembly and parts list Block No. (Subwoofer) Amp. board Trans board Main board Power board Relay board LED board The parts without symbol number are not service.
Page 70
Speaker(Subwoofer) Block No. [M][2][M][M] Symbol No. Part No. Part Name Description Local LV11059-001A CHASSIS BASE LV30225-0T9A SPACER (x2) QYSBSG3008EA TAP SCREW M3 x 8mm(x6) LV30225-0U9A SPACER (x3) LV21942-002A HIAT SINK LV35739-002A IC BRACKET LV36234-001A H/S BRACKET LV44170-001A COOLING RUBBER LV44170-002A COOLING RUBBER LV30227-004A...
Page 71
DVD mechanism assembly and parts list Block No. FXL-D8-1M Grease =JVG-31N =JVS-1003 2.4mm + 0.1mm Letter side APPLY AREA Letter side 7.0mm + 0.1mm Reverse side The parts without symbol number are not service.
Page 72
DVD mechanism Block No. [M][J][M][M] Symbol No. Part No. Part Name Description Local LV10985-001A C.TM CHASSIS QAR0334-002 S.MOTOR QYSPSPU1740ZA SCREW M1.7 x 4mm(x3) QAR0144-003 MOTOR VKS5557-001 F.M. GEAR QYSPSPT2025ZA SCREW M2 x 2.5mm LV35461-002A MIDDLE GEAR LV44040-001A SCREW SHAFT LV35462-001A SCREW SHAFT GEA QAL0667-001...
Page 73
DVD changer mechanism assembly and parts list Block No. FMU-SM1-1M Grease =JVG-31N =JVS-1003 CH5-BASE-1M The parts without symbol number are not service.
Page 74
DVD changer mechanism Block No. [M][K][M][M] Symbol No. Part No. Part Name Description Local LV10913-004A LOADER ASSY QVY0027-B14 S V RESISTOR QYSDST2004ZA TAP SCREW M2 x 4mm QAR0164-001 MOTOR (x2) LV42340-001A MOTOR PULLEY (x2) LV41431-002A BELT (x2) QYSPSPU1725NA SCREW M1.7 x 2.5mm(x2) LV33965-004A LIFTER ASSY...
Page 76
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C4351 NCB30JK-105X C CAPACITOR 1uF 6.3V K C6615 NCB31CK-104X C CAPACITOR 0.1uF 16V K C4391 QETN1AM-477Z E CAPACITOR 470uF 10V M C6616 NDC31HJ-560X C CAPACITOR 56pF 50V J...
Page 77
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R4752 NRSA63J-273X MG RESISTOR 27kΩ 1/16W J UN,US,UT R6205 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R4752 NRSA63J-822X MG RESISTOR 8.2kΩ 1/16W J UG,UX R6206 QRE141J-330Y...
Page 78
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local FW902 QUM21A-06DGZ4-E PARA RIBON WIR S532 QSW0825-001Z TACT SW HS901 GV40606-002A HEAT SINK S533 QSW0825-001Z TACT SW J4401 QNN0570-001 PIN JACK S534 QSW0825-001Z TACT SW J4402...
Page 79
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C1221 NDC31HJ-470X C CAPACITOR 47pF 50V J R1144 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J C1222 NDC31HJ-470X C CAPACITOR 47pF 50V J R1145 NRSA63J-104X MG RESISTOR 100kΩ...
Page 80
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R2588 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J Q3101 IRFB4212 R2590 NRSA63J-333X MG RESISTOR 33kΩ 1/16W J Q3102 IRFB4212 R2592 NRSA63J-333X MG RESISTOR 33kΩ...
Page 81
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D729 MTZJ20B-T2 Z DIODE C701 NCF31HZ-103X C CAPACITOR 0.01uF 50V Z D730 MTZJ20B-T2 Z DIODE C702 NDC31HJ-101X C CAPACITOR 100pF 50V J D734 1SS133-T2 SI DIODE...
Page 82
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C3352 NCB21EK-334X C CAPACITOR 0.33uF 25V K C3768 QFZ0212-224Z MM CAPACITOR 0.22uF C3356 QFZ0212-105Z MF CAPACITOR C3771 NCB31HK-102X C CAPACITOR 1000pF 50V K C3359 QETN2AM-106Z E CAPACITOR...
Page 83
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R558 NRSA63J-223X MG RESISTOR 22kΩ 1/16W J R747 QRK126J-103X UNF C RESISTOR 10kΩ 1/2W J R559 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R749 QRE141J-561Y C RESISTOR...
Page 84
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R3453 NRSA63J-912X MG RESISTOR 9.1kΩ 1/16W J L701 QQL78AK-100 COIL 10uH K R3454 NRSA63J-182X MG RESISTOR 1.8kΩ 1/16W J L702 QQL78AK-100 COIL 10uH K R3455 NRSA63J-132X...
Page 85
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local IC202 SN74HCU04ANS-X C1313 QETN1HM-225Z E CAPACITOR 2.2uF 50V M IC203 RC4558D-X C1322 NCB31HK-272X C CAPACITOR 2700pF 50V K C1331 NDC31HJ-680X C CAPACITOR 68pF 50V J Q1101 KTA1504/YG/-X...
Page 86
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R1341 NRSA63F-682X MG RESISTOR 6.8kΩ 1/16W F R1101 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R1342 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R1102 NRSA63J-103X MG RESISTOR 10kΩ...
Page 87
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R2027 NRSA63J-223X MG RESISTOR 22kΩ 1/16W J C258 NCB31CK-153X C CAPACITOR 0.015uF 16V K R2028 NRSA63J-223X MG RESISTOR 22kΩ 1/16W J C259 NCB31CK-153X C CAPACITOR 0.015uF 16V K...
Page 88
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C557 NCB31HK-102X C CAPACITOR 1000pF 50V K R340 NRSA63D-303X MG RESISTOR 30kΩ 1/16W D C558 NEAF0GM-476X E CAPACITOR 47uF 4V M R341 NRSA63D-512X MG RESISTOR 5.1kΩ...
Page 89
Symbol No. Part No. Part Name Description Local K734 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J K735 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J K736 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J K737 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J K738 NQR0022-005X FERRITE BEADS K741 NQR0022-002X FERRITE BEADS...
Page 90
Packing materials and accessories parts list Block No. A1,A2,A4, A5,A6, A18,A19 A20,A21 3-26...
Page 91
Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GVT0150-007A INSTRUC.BOOK CHI(TAIWAN) GVT0150-008A INSTRUC.BOOK UG,UN,US,UX GVT0150-005A INSTRUC.BOOK CHI(PEKIN) UN,US GVT0150-006A INSTRUC.BOOK ARA PER UG,UX RM-STHC7U REMOTE CON. QMPS310-183-JD POWER CORD(EU) 1.83m BLACK QMPL060-183-JD POWER CORD(EU) 1.83m BLACK UG,UN,US,UX...