Digital Recording From Dat; Digital Signal Interruptions; Miscellaneous Information; Power Interruptions - Pioneer PDR-509 Operating Instructions Manual

Digital recording from DAT

If you're recording a tape that was recorded using the
DAT
machine's auto function, the
DAT ID
slightly after the beginning of the actual recording. This
can cause problems for the
CD
The start of the track may not be recorded.
The track number will be recorded on the disc after
the start of the track
The beginning of the next track on the
unintentionally recorded
To avoid these problems, we recommend recording start
s on the manually, if possible. Refer to the instruc-
ID DAT
tions for your recorder for more information.
DAT
You might also encounter problems if you try to synchro-
record all tracks from a that is set to program play. If
DAT
you want to record a in program play mode, use the
DAT
1-track synchro recording mode— see page 20 for how to
do this.

Digital signal interruptions

There are a couple of situations where a signal arriving at
the digital input of the recorder might be interrupted. The
first is if the sampling rate of the signal suddenly changes.
This is most likely when recording from
record at a number of different sampling rates. If one track
on the is recorded at, say, 44.1kHz, but the next at
DAT
48kHz, this will cause an interruption of the recording on
the PDR-509 while it adjusts to the new sampling rate.
During this time, a short blank section will be recorded
on the disc.
Other sources of signal interruption include power or
source component failure, accidental disconnection of the
interconnect cord, and interruption of digital satellite
broadcasts. In all these cases, if the signal resumes within
about five seconds, the result will just be a blank section
on the disc. If the interruption is longer than five seconds,
the recorder displays the error message:
recording is paused.

Power interruptions

Never switch off the PDR-509 while it's recording, or
while the display shows
PMA REC
Recording). If there's a power failure, or you accidently
disconnect the power from the wall outlet while recording
is in process, you'll lose at least part of the recording.
When power is restored, the recorder will show the
message until it's finished recording the
RESUME
After recording, always remove the disc from the
recorder before switching the power off. Failure to do
this could result in you losing some of the recorded
material on the disc.
s on the tape are
ID
recorder:
is
DAT
, which can
DAT
and
CAN NOT REC
(Program Memory Area
.
PMA
Basic Playback and Recording
Disc type display
When you load a disc, the first thing the recorder does is
to ascertain what kind of disc it is, what (if anything) is
recorded on the disc, and whether or not it's been
finalized. Once it's done this, the display changes to one of
those shown in the table below. If the disc is a
- , the recorder makes a series of automatic adjust-
CD RW
ments to ensure the best quality recording. These
adjustments take a little longer if the unit is cold or has
just been switched on.
A pre-recorded
CD
running time of 55 min. 37 sec.
A finalized
tracks and a running time of 55
min. 37 sec.
Display for a blank consumer-
use
Display for a blank consumer-
use
A partially recorded
10 tracks and a total recorded
time of 43 min. 12sec.
A partially recorded
with 10 tracks and a total
recorded time of 43 min. 12sec.
The disc is not recognized by
the recorder, or you pressed 3
(play) without a disc loaded.
The disc is a professional-use
CD
be used with this recorder.

Miscellaneous information

The minimum recordable time is four seconds.
Even if you try and record something shorter than
this, the track that the recorder creates will be four
seconds.
Usually, track numbers are recorded onto the disc
automatically when recording. If you decide to
switch off this feature (for example, when you're
recording from a satellite broadcast), be sure to
input track markers as recording is taking place —
you can't add them after recording is complete.
See page 30 for more on manual and automatic
track numbering.
The maximum number of tracks on a disc is 99.
- or
CD R
or finalized
CD
– , with 11 tracks and a
R
– with 11
CD RW
– disc.
CD R
– disc.
CD RW
– with
CD R
–
CD RW
- or - disc and cannot
R CD RW
19