Pioneer PDR-509 Operating Instructions Manual page 38

Additional Information
It's often easy to mistake incorrect operation for trouble and malfunction of the unit. If you think there is something wrong
with the component, check the points below first. If the problem persists, contact you nearest Pioneer-authorized service
center and have them check over the unit.
Symptom
Power cannot be turned
on.
No sound is heard
during playback.
Cannot record.
Recorded sound is
distorted.
Remote control opera-
tion is impossible.
Some tracks are skipped
without being played.
Skip playback does not
occur.
A recorded – disc
CD R
cannot be played on
other players.
CD
The point-of-sale
demonstration is
displayed.
If digital synchro-recording fails to operate correctly, check the following:
1. Pause playback of the source, then press the DIGITAL SYNCHRO button again.
÷ If you're recording from a portable CD player, etc., make sure that the shock-protection feature is
switched off.
2. Start playback of the source component once you see the SYNCHRO indicator start to blink.
3. If none of the above solves the problem, use manual digital recording to record.
÷ Digital synchro-recording uses a digital sub-signal contained in the source player's digital output. Digital
synchro-recording will not work when recording from the following devices:
÷ CD players whose digital output does not include a sub-signal
÷ Portable CD, MD or DVD players which do not output a digital signal when stopped.
38
Cause
¶
The power cord is unplugged from the wall
outlet.
¶
The power was turned off from the compo-
nent (stereo amplifier, audio timer, etc.) to
which it is connected.
The recorder is not connected up properly.
¶
The recorder is not connected up properly.
¶
The – or – disc in use has already
CD R CD RW
been finalized.
¶
The input selection is incorrect.
¶
The control is set too low.
REC LEVEL
¶
The ecording level is set too high.
¶
Signal connections are incorrect.
¶
There is interference from a TV set.
¶
The disc is damaged or warped.
¶
The disc is extremely dirty.
¶
The remote control batteries are exhausted.
¶
There is an obstacle between the remote
control unit and main unit.
¶
The remote control unit is being operated
outside the remote controllable range.
The button is set to on.
SKIP PLAY
The button is set to off.
SKIP PLAY
¶
The disc has not been finalized after
recording. When such a disc is loaded in the
unit, the – indicator lights.
CD R
¶
The pickup lens of the other
dirty, impairing its ability to play
See page 36 for instructions on how to cancel
the store demo mode.
Remedy
¶
Plug the power cord into a power outlet.
¶
Turn on the component supplying the
power to the recorder.
Check all connections, especially to the
amplifier—pp.10–11
¶
Check all connections— pp.10–11
¶
Use a non-finalized disc or erase the
–
CD RW
¶
Select the input connected to the source
component you're recording from.
¶
Increase the recording level— pp.24–25
¶
Reduce the recording level—pp.24–25
¶
Check all connections— pp.10–11
¶
Turn the
further away from the
¶
Use another disc.
¶
Clean the disc.
¶
Replace both of the remote control
batteries with new ones.
¶
Remove the obstacle.
¶
Operate in the remote controllable
range—p.14
Set the
SKIP PLAY
Set the
SKIP PLAY
¶
Finalize the disc— p.33
¶
player is Try the disc on a different
CD
– discs. plays
CD R OK
original player cleaned.
disc— pp.34–35
power off or install this unit
TV
.
TV
button to off—p.27
button to on —p.27
player. If it
CD
then get the pickup lens on the