Table of Contents
Advertisement
Quick Links
Agilent U1177A IR-to-Bluetooth Adapter
Operating Instructions
The Agilent U1177A IR-to-Bluetooth
multimeter (DMM) only where it allows Bluetooth communication between the meter and PC.
The U1177A is powered by two AAA batteries, able to operate about 30 hours on new alkaline
batteries, and provides up to 10-metres connectivity solution.
Front View
LED Indicator and Slide Switch
Standard Shipped Items Checklist
The following items are included when you make a purchase:
• U1177A IR-to-Bluetooth adapter
• Two 1.5 V AAA batteries
• Operating Instructions (this sheet)
Assistance
For technical assistance, contact your nearest Agilent Sales Office or visit the Agilent website at
www.agilent.com/find/assist for further information.
The Bluetooth
word mark and logos are registered trademark owned by Bluetooth SIG, Inc and any use of such
1
®
marks by Agilent is under license. Other trademark and trade names are those of their respective owners.
adapter is designed for the use of Agilent handheld digital
®1
Low battery — LED red flashing
1. Bluetooth disconnection — LED green flashing
2. Bluetooth connected — LED solid green
3. Bluetooth power off — LED off
Slide switch
Advertisement
Table of Contents
Related Manuals for Agilent Technologies U1177A
Summary of Contents for Agilent Technologies U1177A
-
Page 1: Front View
®1 multimeter (DMM) only where it allows Bluetooth communication between the meter and PC. The U1177A is powered by two AAA batteries, able to operate about 30 hours on new alkaline batteries, and provides up to 10-metres connectivity solution. Front View LED Indicator and Slide Switch Low battery —... -
Page 2: Product Characteristics
WEIGHT: 60 g with battery WARRANTY: Three months BLUETOOTH: Bluetooth Version 2.1 + EDR compliant, SPP profile, Class 2 device SAFETY: The U1177A complies with the requirements of the following safety standards: • FCC Part15C (Certification) (15.209, 15.247) FCC ID: ZKMAGILENT–U1177A •... -
Page 3: Default Configurations
If the LED is not lighted when turned on, replace the batteries with new specified batteries. • The adapter can only be used with Agilent handheld digital multimeters Configuration Table below shows you the default configurations for the U1177A. Parameters Default Configurations PIN code 1234... -
Page 4: Operation
10. Click Finish to complete the connection. The U1177A-XXXXXX is now added and connected successfully. 11. If you already had the U1177A added in My Bluetooth Places, double-click U1177A to establish a wireless serial connection with your remote multimeter. 12. Double-click the U1177A again to disconnect the wireless serial connection. - Page 5 Install and Replace the Batteries Make sure you turn off the U1177A before installing or replacing the batteries. 1. Slide the battery cover 2. Insert the battery. 3. Reverse the sliding position away from adapter’s body. to close the battery cover.
- Page 6 Only one host computer is able to connect the U1177A at a time. Configure U1177A Remotely via Hyper Terminal Hyper Terminal is a program that enables you to configure your U1177A remotely using the AT commands—in this case via Bluetooth connection.
-
Page 7: At Command List
AT Command List Command Usage Description This command controls the deep sleep timer. The U1177A will enter deep sleep mode and turn off all the LEDs when there is no event Power Management activity. The timer will restart once an event interupt the timer. The Control U1177A will wake up once the UART received a proper signal. -
Page 8: At Command Examples
// Set the PIN number to 8080 ATZ0 // Set the device to default setting Maintenance If any part of the adapter is worn out or damage, replace it with a new U1177A adapter. U1177-90101 ©Agilent Technologies, Inc., 2011 Printed in China...