Epson EMP-810 User Manual page 45

Tip : Tip :
• When ke • The [Au
screen is b
• Procedu
you need
1. With th
button on
2. Extend
Turning On the Power and Projecting Images
If the projector cannot be set up so that it is perpendicular to the screen, you can
• If you us
3. Adjust
use the keystone correction function which is described on the following page
Zoom, A/
4. Adjust
to adjust the projected images if the angle of the projector is within a range of will be ca
Procedure
picture ar
projector'
approximately 30° vertically or approximately 10° horizontally from the
• The keys
E-Zoom o
1 Turn on the power for all equipment connected to the projector.
perpendicular.
angle of th
• Automat
The values given here are for when the image is at the smallest zoom setting
For a video source, press the [Play] button at the video source to start
To return
output by
(telephoto). The maximum angles will be smaller if the zoom setting has been
playback if necessary.
operations
synchroni
increased in the wide angle direction. Furthermore, if the projector has been
To initaliz
tilted both vertically and horizontally, the maximum adjustable angle will again
press the [
Check that the operation indicator
2
be smaller than the maximum angle if the projector had been tilted in only one
To initaliz
has stopped flashing and lights
direction.
button, pr
orange.
• If the im
• When tilted vertically
decrease t
• Keyston
Adjusting the tracking
Approx. 30° above
• If you ca
If vertical stripes appear in the projected images,
will becom
and this cannot be fixed using automatic
• If the va
adjustment. You will need to adjust the tracking
If using the remote control, set the
3
vertical ke
manually using the following procedure.
R/C switch on the remote control to
horizontal
the ON position.
has not be
Procedure
• If either
or vertical
While holding down the [Shift] button
screen if t
on the projector's control panel, press
limit. It m
the [Tracking +] button.
Press the [Power] button on either
4 happens. I
The tracking value will increase by one setting
correction the remote control or the
each time the [Tracking +] button is pressed.
projector's control panel to turn on
• The limi
• When tilted horizontally
the power for the projector.
input.
Approx. 10° to the right
The operation indicator flashes green, and
after a short period projection starts.
Depending on the settings, the message
"No-Signal." may appear. (P.70)
[While holding down the [Shift] button
on the projector's control panel, press
5 Check that the operation indicator
the [Tracking -] button.
has stopped flashing and lights
The tracking value will decrease by one setting
green.
each time the [Tracking -] button is pressed.
Tip :
The projector buttons cannot be operated while the
Tip :
operation indicator is flashing green. Wait until it
The image will flash when continuous tracking
lights steadily.
adjustment is carried out, but this is normal.
Downloaded from ProjectorsManual.com Manuals Downloaded from ProjectorsManual.com Manuals Downloaded from ProjectorsManual.com Manuals Downloaded from ProjectorsManual.com Manuals
30°
10°
sett m
Approx. 30° below
Operation indicator lights orange
30°
Sync+
Tracking -
Power
Help
Computer/YCbCr Video
Source
Menu Esc
Shift
Approx. 10° to the left
Sync+
Tracking - Tracking +
A to
Resi e
Projector
Projector
Sync+
Tracking -
Shift
R i
Operation indicator stops
flashing and lights green
Projector
Tracking +
Auto
Power
A/V Mute Freeze
E-Zoom
Keystone
Sync-
Remote control
Tracking +
Auto
Keystone
10°
Sync-
37