Page 1
XV-M50BK SERVICE MANUAL DVD VIDEO PLAYER XV-M50BK STANDBY/ON DISC SELECT PLAY TV/VIDEO MODE PHONIC CANCEL RETURN TV -/-- MUTING THEATER ANGLE SUBTITLE AUDIO POSITION DISC 3 DIGEST ZOOM DISC STANDBY PLAY & EXCHANGE DISC 2 DISC DVD / VIDEO CD / CD...
Page 2
XV-M50BK 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits.
Page 3
XV-M50BK Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.1. Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
Page 4
XV-M50BK Precautions for Service Handling of Traverse Unit and Laser Pickup 1. Do not touch any peripheral element of the pickup or the actuator. 2. The traverse unit and the pickup are precision devices and therefore must not be subjected to strong shock.
Page 6
XV-M50BK Top cover Disassembly method <Main body> Removing the top cover (See Fig.1) Remove the two screws A attaching the top cover on the back of the body. Remove the four screws B attaching the top cover on both sides of the body.
Page 7
XV-M50BK Removing the rear panel (See Fig.6) Rear panel Prior to performing the following procedure, remove the top cover. Remove the eleven screws D attaching the rear panel on the back of the body and detach the rear panel. Fig.6...
Page 8
XV-M50BK Removing the power supply board (See Fig.8 and 9) Rear panel CN951,CN952 Power supply board Prior to performing the following procedure, remove the top cover. Disconnect the wire from connector CN971 on the power supply board (The wire is extending from the front panel assembly).
Page 9
XV-M50BK Removing the video board Rear panel CN601 Video board (See Fig.10 and 11) Prior to performing the following procedure, remove CN704 the top cover. Disconnect the card wire from connector CN601 on the video board (The card wire is extending from the DVD changer mechanism assembly).
XV-M50BK <Front panel assembly> Front panel assembly Prior to performing the following procedure, remove Bracket the top cover and the front panel assembly. Removing the front board (See Fig.14 and 15) Remove the two screws I on the back of the front...
Page 11
XV-M50BK <DVD changer mechanism assembly> DVD changer mechanism assembly Prior to performing the following procedure, remove the top cover and the DVD changer mechanism assembly. Removing the traverse mechanism control board (See Fig.17) Disconnect the card wire from connector CN101 on...
Page 12
XV-M50BK <DVD Changer Mechanism Section> Removing the DVD mechanism board (See Fig.1) Remove the DVD changer mechanism assembly. From bottom side the DVD changer mechanism assembly, remove the one screw A retaining the DVD servo control board. Disconnect the card wire from the connector CN101 on the DVD servo control board.
Page 13
XV-M50BK Stopper Check whether the lifter unit stopper has been caught into the hole at the section e of DVD tray assembly as shown in Fig.5. Make sure that the driver unit elevator is positioned as shown in Fig.6 from to the second or fifth hole on the left side face of the DVD Traverse mechanism assembly.
Page 14
XV-M50BK Cams R1, R2 assembly Removing the DVD mechanism assembly(See Fig.10) While turning the cams R1 and R2 assembly in the arrow direction h , align the shaft i of the DVD mechanism assembly to the position shown in Fig.10.
Page 15
XV-M50BK Removing the mechanism control board (See Fig.14, 15) Motor L Motor R Absorb the four soldered positions m of the right and left motors with a soldering absorber(See Fig.14). Remove the two screws H retaining the mechanism control board(See Fig.14).
Page 16
XV-M50BK Removing the actuator motor and belt Gear bracket (See Fig.19 Remove the two screws K retaining the gear bracket (See Fig.19). While pressing the pawl p fixing the gear bracket in the arrow direction, remove the gear bracket Pulley gear (See Fig.19).
Page 17
XV-M50BK Slit washer Removing the cams R1/R2 assembly and cam gear L (See Fig.23) Cam R2 Slit washer Remove the slit washer fixing the cams R1 and R2 assembly. Cam gear L By removing the two pawls s fixing the cam R1, separate R2 from R1.
Page 18
XV-M50BK Pickup unit < DVD Traverse mechanism section> Removing the pickup (See Fig.1 to 5) Flexible board Solder soldering a on the flexible board next to the pickup unit. From the bottom of the traverse mechanism unit, disconnect the flexible wire from CN12 on the pickup board.
Page 19
XV-M50BK Removing the pickup board (See Fig.1 and 6) Pickup unit Solder soldering a on the flexible board next to the pickup unit. Flexible board From the bottom of the traverse mechanism unit, disconnect the flexible wire from CN12 on the pickup board.
Page 20
XV-M50BK Removing the turn table assembly Pickup unit (See Fig.1, 6, 8 and 9) Solder soldering a on the flexible board next to the Flexible board pickup unit. From the bottom of the traverse mechanism unit, disconnect the flexible wire from CN12 on the pickup board.
Page 21
XV-M50BK Adjustment method (1) Initialization method If microprocessor (IC401,IC402,IC403) or pick-up is replaces, initialize the DVD player in the following matter 1)Take out the disc and close the tray. 2)Unplug the power plug. 3)Insert power plug into outlet while pressing both PLAY button and DISC 1 OPEN/CLOSE button.
Page 22
XV-M50BK For Jitter value The jitter value is displayed by the hexadecimal number and refer to the conversion table of following,please. If the indication value is 11% or less, it can be judged by this simple checking method that the signal read precision of the set is satisfactory.
Page 23
XV-M50BK When replacing a pickup etc., execute the following adjustments: CN10 Pickup replacement Traverse 1. When removing the traverse mechanism from the CN12 mechanism changer mechanism unit, move the pickup to the innermost diameter of the disc and set switch (S11) on the pick-up board on "SHORT"...
Page 24
XV-M50BK Integrated wiring for adjustment Extension cord QUQ605-4040AJ 1. Place a board on top of the unit and put the changer on it. Then carry out the wiring of the main unit. 2. Connect a extension cable to the traverse mechanism for adjustment and then connect them to the changer.
Page 26
XV-M50BK 3.Pin function AN8706FHQ (1/2) Pin No. Symbol Functions LDONB Laser ON (CD Head) terminal LDONA Laser ON (DVD Head) terminal LPCOA Laser drive output terminal LPC1 Laser PIN input terminal VHARF VHALF voltage output terminal TGBAL Tangential phase balance control terminal...
Page 27
XV-M50BK AN8706FHQ(2/2) Pin No. Symbol Functions VCC5 Power terminal 5 (3.3V) IDGT Data slice address part gate signal input terminal (For RAM) DTRD Data slice data read signal input terminal(For RAM) CAPA Data slice CAPA(Address)signal input terminal (For RAM) VCC3...
Page 29
XV-M50BK 3.Pin function MN67705EA (1/3) Pin No. Symbol Function H fixation LDONA Laser drive controlA (ON / OFF) LDONB Laser drive controlB (ON / OFF) PULIN DSL and PLL high boost signal (FEP) Head amplifier gain H/L selection DVSS Ground for digital circuit...
Page 30
XV-M50BK MN67705EA (2/3) Pin No. Symbol Function IREF3 Connects with unused DVSS VCOF2 Connects with unused DVSS DVSS Ground for digital circuit VCOE3 Connects with unused DVSS DVSS Ground for digital cirucuit DVDD Power supply for digital cirucuit SUBC CD sub-code (ODC)
Page 31
XV-M50BK MN67705EA (2/3) Pin No. Symbol Function IREF3 Connects with unused DVSS VCOF2 Connects with unused DVSS DVSS Ground for digital circuit VCOE3 Connects with unused DVSS DVSS Ground for digital cirucuit DVDD Power supply for digital cirucuit SUBC CD sub-code (ODC)
Page 32
XV-M50BK MN67705EA(3/3) Pin No. Symbol Function FS (FEP) FS(AD2) TS (FEP) TS(AD1) Ground for analog cirucuit AVSS Power supply for analog circuit AVDD Focus balance(FEP) FBAL(DA1) Cutting off frequency (FEP) FC(DA2) Amount of boost (FEP) BOOST(DA3) DSL offset balance (FEP)
Page 35
XV-M50BK 3.Pin function MN103007BGA(1/4) Symbol Function Pin NO. HDD15 ATAPI data HDD0 ATAPI data HDD14 ATAPI data 5VDD HDD1 ATAPI data HDD13 ATAPI data HDD2 ATAPI data HDD12 ATAPI data HDD3 ATAPI data HDD11 ATAPI data HDD4 ATAPI data HDD10...
Page 36
XV-M50BK MN103007BGA(2/4) Symbol Function Pin NO. CPUADR10 System control address CPUADR9 System control address CPUADR8 System control address CPUADR7 System control address CPUADR6 System control address CPUADR5 System control address CPUADR4 System control address CPUADR3 System control address CPUADR2 System control address...
Page 37
XV-M50BK MN103007BGA(3/4) Symbol Function Pin NO. Land / group switch NTRON Tracking ON DACDATA Serial output DACLRCK L and R identification output DACCLK Clock for serial output IPFLAG Interpolation flag input BLKCK Sub-code,Block clock input LRCK L and R identification signal output OSCI1 16.9MHz oscillation...
Page 38
XV-M50BK MN103007BGA(3/4) Symbol Function Pin NO. Land / group switch NTRON Tracking ON DACDATA Serial output DACLRCK L and R identification output DACCLK Clock for serial output IPFLAG Interpolation flag input BLKCK Sub-code,Block clock input LRCK L and R identification signal output OSCI1 16.9MHz oscillation...
Page 39
XV-M50BK TC7SH08FU-X (IC311) : Timing control TC7SH32FU-X (IC312) : 2 Input Single OR Gate 1.Terminal layout 1.Terminal layout IN B IN A OUT Y TC74VHC00FT-X (IC322,IC503) : Write timing control 1.Terminal layout / Block diagram TC74VHC125FT-X (IC411) : Buffer 1. Pin layout & block diagram 2.
Page 40
XV-M50BK IC-PST9140-T (IC702) : TC7S07F-W (IC704) : 2 Input Single AND Gate SYSTEM RESET 1.Terminal layout 1.Terminal layout IN B IN A GND NJM4580M-X (IC741,IC751) : PQ05RD21 (IC951) : Regulator Dual Operational Amplifier 1.Terminal layout 1.Terminal layout (TOP VIEW) A OUTPUT...
Page 41
XV-M50BK ZIVA-4.1-PA2(IC501):Back end - Digital decoder 1.Terminal layout 2.Pin function (1/5) Pin No. Symbol Description Read strobe input Read/write strobe input Power supply terminal 3.3V Transfer not complete / data acknowledge. WAIT Active LOW to indicate host initiated transfer is complete.
Page 42
XV-M50BK 2.Pin function (2/5) Pin No. Symbol Description Connect to ground Non connect Non connect Non connect Non connect Non connect Programmable I/O terminal PIO0 Connect to ground Power supply terminal 3.3V Programmable I/O terminal PIO1 Programmable I/O terminal PIO2...
Page 43
XV-M50BK 2.Pin function (3/5) Pin No. Symbol Description SDRAM address MADDR6 SDRAM address MADDR5 Power supply terminal 2.5V Connect to ground SDRAM address MADDR4 SDRAM write enable Active LOW SDRAM column address SD-CAS Power supply terminal 3.3V Connect to ground...
Page 44
XV-M50BK 2.Pin function (4/5) Pin No. Symbol Description Connect to ground Non connect VSS_DAC Connect to ground for analog video DAC VSS_VIDEO Connect to ground for analog video DAC video output format : CVBS. Macrovision encoded CVBS VDD_DAC Power supply terminal for analog video DAC...
Page 45
XV-M50BK 2.Pin function (5/5) Pin No. Symbol Description DVD parallel compressed data from DVD DSP. or CD-G clock indicating DVD-DATA7/CDG-SCLK sub code data clock input or output VDACK In synchronous mode, bitstream data acknowledge. Asserted when DVD data is valid.Polarity is programmable...
Page 46
XV-M50BK MN101C12G (IC701) : System micom 1.Terminal layout 100 ~ 76 26 ~ 50 2.Pin function Pin No. Symbol Function A set bit0 (It is effective in the U.E version) A set bit1 (It is effective in the U.E version) A set bit2 (It is effective in the U.E version)
Page 47
XV-M50BK MN101C12G (2/2) Pin No. Symbol Function 48kHz, 96kHz switch CHREQ Changer communication REQUEST CHST Changer communication STROBE CHDATA Changer communication DATAI/O Un used CHCK Changer communication CLOCK FLDATAO FL driver communication DATAO FLDATAI FL driver communication DATAI FLCK FL driver communication CLOCK...
Page 52
XV-M50BK 2.Pin function M35500BGP Function Pin No. Symbol XOUT Both terminals are short-circuited on the outside, and capacity is connected. 0v is supplied to vss. Both terminals are short-circuited on the outside, and capacity is connected. RESET Reset input of active "L"...
Page 54
XV-M50BK VICTOR COMPANY OF JAPAN, LIMITED PERSONAL & MOBILE NETWORK BUSINESS UNIT 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan Printed in Japan No.A0008 200106(S)
Page 56
XV-M50BK Power supply section (SHEET 6) DVD Servo control section (SHEET 1,2) CN502 CN503 CN971 CN961 CN981 CN951/CN952 WAITDEC CN101...
Page 57
XV-M50BK VIDEO OUT System control section (SHEET 3) Video out section (SHEET 4) J601 LVA10018-A3 Q601 Q611 FLRST,STANDBY IND TO CN801 FLCK,FLDATAI/O TO CN951 SHEET 5 RESET EEPROM FLCS,REMO RESET SHEET 6 IC791 IC702 POWER SW P.ON POWER X701 +12V...
Page 69
XV-M50BK PARTS LIST [XV-M50BK] * All printed circuit boards and its assemblies are not available as service parts. Area Suffix J ------------------- U.S.A. C --------------- Canada - Contents - Exploded view of general assembly and parts list DVD changer mechanism assembly and parts list...
Page 70
XV-M50BK Exploded view of general assembly and parts list Exploded view of general assembly 1/2 Block No.
Page 71
XV-M50BK Exploded view of general assembly and parts list Block No. Exploded view of general assembly 2/2 57 64 57 59...
Page 72
XV-M50BK (General assembly)1/2 Parts list Block No. M1MM Item Parts number Parts name Q'ty Description Area LE10246-010A FRONT PANEL VJD5429-001SS JVC MARK LE20522-001A PUSH BUTTON POWER LE40745-001A INDICATOR POWER PLAY LE20521-001A PUSH BUTTON LE30889-001A INDICATOR DISC LE20523-004A WINDOW SCREEN QYSDSF2608Z...
Page 73
XV-M50BK (General assembly)2/2 Parts list Block No. M1MM Item Parts number Parts name Q'ty Description Area QJJ015-091406 SIN CR C-C WIRE QUQ110-0918AM FFC WIRE E309662-001SM DISC STOPPER QYSBSF3008Z SCREW QYSBST3008Z T.SCREW LV20821-039A REAR PANEL QYSBSGY3008E SPECIAL SCREW REAR PANEL QYSBSGY3008E...
Page 74
XV-M50BK DVD changer mechanism assembly and parts list Block No. FLM-C5-3M Grease and screw lock EM-30L EBS0006-009B...
Page 75
XV-M50BK Parts list (DVD changer mechanism) Block No. M2MM Description Item Parts number Parts name Q'ty Area VKS1144-003 CHASSIS VKS3698-003 TRAY GUIDE VKS5532-003 PULLEY GEAR VKB3000-164 BELT VKS5505-003 GEAR B VKS5506-002 GEAR C VKS5507-002 CROSS GEAR U VKS5508-002 CROSS GEAR L...
Page 76
XV-M50BK DVD Mechanism assembly and parts list Block No. FXL-V62-1M Grease & Three bond = EBS0006-013B =CFD-4007HYS =946P =1401B Relay board 65.2 12.0 0.2mm...
Page 77
XV-M50BK Parts list (DVD mechanism) Block No.M3MM Parts number Parts name Q'ty Description Item Area LV20638-001A MECHA BASE LV20635-001A SHAFT HOLDER QYSBST2606M T.SCREW VDG1099001TSVME SP.MOTOR ASS'Y QUM193-08B2B2 PARA RIBON WIRE FOR S.BASE&M.BASE QYSBST2606M T.SCREW OPTIMA-2010B1 DVD PICKUP LV31670-001A SWITCH ACTUATOR...
XV-M50BK Electrical parts list Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area BK801 E308192-001 FL HOLDER C 811 NCB31CK-104X C CAPACITOR C 601 NCS31HJ-471X C CAPACITOR...
Page 79
XV-M50BK Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area CN952 QGD2501C1-04Z SOCKET J 701 QNN0170-002 PIN JACK AUDIO OUT CN961 QGA2001C1-09 9P PLUG ASSY J 702 QNS0089-001 3.5 JACK...
Page 80
XV-M50BK Electrical parts list (Mian board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 614 NRSA63J-0R0X MG RESISTOR R 766 NRSA63J-273X MG RESISTOR R 615 NRSA63J-221X MG RESISTOR R 767...
Page 81
XV-M50BK Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area R 969 NRSA63J-221X MG RESISTOR R 971 NRSA63J-392X MG RESISTOR R 972 NRSA63J-122X MG RESISTOR R 973 NRSA63J-102X MG RESISTOR R 974 NRSA63J-562X MG RESISTOR...
Page 82
XV-M50BK Electrical parts list (Servo control board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area NCB31CK-104X C CAPACITOR C 237 NCB31CK-104X C CAPACITOR NEA70JM-226X E CAPACITOR C 238 NCB31CK-104X C CAPACITOR...
Page 83
XV-M50BK Electrical parts list (Servo control board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 342 NCB31CK-104X C CAPACITOR C 561 NCB31CK-104X C CAPACITOR C 343 NCB31CK-104X C CAPACITOR C 562...
Page 84
XV-M50BK Block No. 02 Electrical parts list (Servo control board) Item Remarks Parts name Area Item Remarks Parts number Parts name Area Parts n mber R 108 NRSA63J-183X MG RESISTOR R 243 NRSA63J-102X MG RESISTOR R 109 NRSA63J-0R0X MG RESISTOR...
Page 85
XV-M50BK Electrical parts list (Servo control board) Block No. 02 Item Parts number Parts name Remarks Area R 405 NRSA63J-472X MG RESISTOR R 408 NRSA63J-472X MG RESISTOR R 411 NRSA63J-472X MG RESISTOR R 412 NRSA63J-103X MG RESISTOR R 413 NRSA63J-472X...
Page 86
XV-M50BK Block No. 03 Electrical parts list (Conection board) Block No. 05 Electrical parts list (DVD changer mechanism switch board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 13 NCS31HJ-101X C CAPACITOR CN804...
Page 87
INST BOOK LET0183-001B INST BOOK LE40805-002B INST SHEET QMPE200-183-JC POWER CORD BT-51020-2 J=REGIST CARD YU20333 SAFETY INST. BT-52004-1 WARRANTY CARD BT-20071B JVC CENTER LIST QAM0328-001 AV CORD 3P QAM0223-001 PLUG CORD A 10 RM-SXVM50J REMOCON UNIT A 11 -------- BATTERY 3-19...