Table of Contents
Advertisement
Index
Modulator Block Diagram, 4–5
Modulator Checkout, 5–3
Modulator Faults, 3–40, 5–13
Modulator IF Output Shape, C-25
Modulator Phase Error, C-26
Modulator Power Offset, C-25
Modulator-Related Speciofications, C-21
Modulator Specifications, 4–6
Modulator Spectrum, C-26
Monitor, 1–5, 3–2, 3–5, 3–36, 3–37, 3–47, 3–75, 3–80,
3–81, 4–1, 5–3, A–20, A–26, B–31, B–36, B–48, B–49,
B–54
Monitor and Control (M&C), 1–5, 4–1
Monitor Menu, 3–36
Monitor Signals, C-47
Multiples of the Frame Length, 3–98
Multiplexer Specification, A–79, A–81
MUX Data 100-Pin Connector (J10), A–78
MUX Operation, A–24
MUX PCB Configuration Commands (MUX PCB Installed
Only), B–17
N x 64 Chart, 3–79
Non-ASYNC Operation, A–26
Open Network, 4–16
Operation, 1–10, 2–4, 2–6, 3–68, 3–77, 3–78, 3–79, 3–80,
3–83, 3–84, 3–85, 4–6, 4–10, A–12, A–24, A–26, A–42,
A–62, B–6, B–7, B–14, B–21, B–22, B–23, B–25,
B–26, B–44, B–50
Optional 37-Pin Connector Pinouts, 2–11
Options, 1–7, 1–8, 1–9, 2–9, 3–86, A–1, A–4, A–6, A–60,
B–50, B–51
Overhead Board Field-Changeable Chips, A–73
Overhead Interface PCB, A–69, A–71, A–73
Overhead Interface PCB Installation, A–69, A–71
Overhead Option, 50-Pin D Connector, 2–5
Pin Assignment, A–85
Performance with Noise, Viterbi Decoder, and Open
Network Mode, C-6
Performance with Noise, Viterbi Decoder, and Closed
Network Mode, C-8
Performance with Noise, Viterbi Decoder, and Reed-
Solomon (Optional), C-10
Performance with Noise, 56 kbit/s and Sequential Decoder
(Optional), C-12
Performance with Noise 1544 kbit/s and Sequential
Decoder (Optional), C-14
Performance with Noise, at 1544 kbit/s, Sequential
Decoder and Reed-Solomon, C-16
Phase Noise, C-24
Plesiochronous, 3–93, 3–97, 3–98, 4–15, A–8, A–13, A–82
Plesiochronous /Doppler /Buffer, 4–15
Plesiochronous Buffer, A–8, A–13, A–82
i–4
N
O
P
QPSK Encoding, 4–8
Receive Clock Switching Due to Failure of Selected Clock,
C-33
Receive Clock Jitter, C-33
Receive Clock Phase Adjustment, C-33
Receive Data Phase Adjustment, C-33
Receive DEMUX, A–12, A–13
Receive Doppler/Plesiochronous Buffer Size, C-34
Receive Frequency, C-30
Receive IF Carrier Acquisition Range, C-20
Receive IF Carrier Reacquisition, C-20
Receive Input Power (Composite), C-30
Receive Input Power (Desired Carrier), C-30
Receive Interface Faults, 3–41, 5–16
Receive Section of the Asymmetrical Loop Timing Block
Diagram, A–57
Reed-Solomon Code Page Format, A–64
Reed-Solomon Codec, 1–7, 3–45, A–1, A–60, A–61, A–62,
A–63, A–65, A–67, A–68
Reed-Solomon Codec Block Diagram, A–61
Reed-Solomon Codec Installation, A–68
Reed-Solomon Decoder, A–1, A–45, A–65, B–7, B–25,
B–26, B–42
Reed-Solomon Decoder Section Block Diagram, A–65
Reed-Solomon Encoder, A–1, A–62, B–5, B–21, B–22,
B–42
Reed-Solomon Encoder Section Block Diagram, A–62
Reed-Solomon PCB (AS/5304-1), A–60
Reed-Solomon Specifications (Optional), A–66
Remote Address, 3–75, 4–4
Remote ASYNC Connection Diagram for Breakout Panel,
A–29
Remote ASYNC Connection Diagram for Y Cable, A–29
Remote AUPC, 3–2, 3–5, 3–46, 3–47, 3–75, 3–80, A–23,
A–27, B–16, C-40
Remote AUPC Configuration, 3–46, 3–47, A–27
Remote AUPC Configuration Menu, 3–46
Remote AUPC Monitor, 3–46, 3–47, A–27
Remote AUPC Monitor Menu, 3–46
Remote Control, C-46
Remote Baud Rate, 3–75, 4–4, A–30, A–31, A–32, A–33,
A–34, A–35, A–36, A–38
Remote Connector and Pinouts (J6), 2–6
Revision Emulation Operation, 3–85
RF Input Connector (CP2), 2–19
RF Loopback, 3–72, 3–74, A–18, A–50, A–54, B–6, B–25,
B–26
RF Output Connector (CP1), 2–19
Scrambling Types, C-23,
SDM-100 Emulation Operation, 3–83
SDM-100 Emulation Parameter Settings, 3–83
SDM-300A Custom Modem Defaults, 3–74, 3–75, 3–76
SDM-300A Fault Tree, 5–9, 5–10, 5–11
SDM-300A Revision Emulation, 3–85
SDM-300A Satellite Modem
Q
R
S
Rev. 4
Advertisement
Table of Contents
