Related Manuals for Miele G 7836 CD
Summary of Contents for Miele G 7836 CD
- Page 1 Operating and Installation Instructions Laboratory Glassware Washer G 7836 CD To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 06 868 470...
-
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS ....... . . 4 Description of the machine ......... . 8 Guide to the machine. - Page 3 Contents Maintenance ........... . . 33 Process validation .
-
Page 4: Important Safety Instructions
Regard the A damaged machine is dangerous. information from the glassware Turn off the machine immediately at manufacturer. the main switch and call the Miele Miele is not responsible for damages Service Department. caused by improper use. Personnel operating the machine The installation of this unit in non should be trained regularly. - Page 5 IMPORTANT SAFETY INSTRUCTIONS Take care when handling liquids After drying with the TA drying unit such as detergents, neutralizing open the door to allow the items agents, wetting agents and rinse aids. and inserts to cool. These may contain irritant or corrosive Do not touch the heating elements ingredients, acids or alkalis.
- Page 6 For pre-treatment and/or cleaning only use low-sudsing detergents and disinfecting agents which have been approved by Miele. Suds can have an adverse effect on the cleaning process.
- Page 7 Consult the such as cleaning agent, quality of Miele Professional Group on the type water, etc. are discussed with a Miele and application of such equipment. Applications Specialist. The mobile units and special...
-
Page 8: Description Of The Machine
Description of the machine The Miele G 7836 Standard Capacity Optional peripheric machines Glassware Washer is designed for – Report printer (PRT) high-throughput, centralized wash – Dispensing systems DOS 2 and areas. This unit is ideal for cleaning both large volumes of small items, and DOS 4 difficult to clean large items. -
Page 9: Guide To The Machine
Guide to the machine a Electronic control g Storage container for dispensing systems DOS 2 and DOS 4 (optional) b Serial interface, rear of the machine h DOS drawer (upper left, behind the cover plate) c Probe access for validation i Container for neutralizing agent (red) and liquid cleaning agent (blue) d Connector for salt container... - Page 10 Guide to the machine Electronic controls...
- Page 11 Guide to the machine a Display g Door button 5 with screen saver h Start button 6 The background light turns off – Starting a program automatically after 15 minutes. – Activating insert mode – Confirming settings ^ Press any key to turn the background –...
-
Page 12: Opening And Closing The Door
Opening and closing the door Electric door lock To open the door with the emergency release The machine is equipped with an electric door lock. The emergency release should The door can only be opened if: only be used when the door cannot be opened normally, e.g. -
Page 13: Water Softener (Optional)
Water softener (optional) Setting the water softener To achieve good cleaning results, the labwasher needs soft water. Hard tap Miele's Technical Service sets the local water results in calcium deposits on the water hardness when installing and glassware and in the labwasher. -
Page 14: Filling The Salt Reservoir
Filling the salt reservoir Only special, coarse-grained reactivation salt* should be used in this machine. *Available from Miele. Please see back page for contact information. Do not use other types of salt, e.g. table salt, agricultural or gritting salt. These... - Page 15 ^ Open the door and carefully remove the salt container. If the container will not come off manually contact the Miele Service Department. ^ Replace the plastic cap. ^ Remove the plastic cap on the upper ^ Return the mobile unit into the wash right-hand side of the wash cabinet.
-
Page 16: Automatic Mobile Unit Recognition (Awk)
Automatic mobile unit recognition (AWK) Mobile unit coding In operating level C the (optional) AWK allocates a fixed program place to a The AWK assigns a program place to a mobile unit with valid coding. mobile unit. The mobile units must be Program places 1-15 are reserved for coded with a magnetic strip via a Bit the AWK automatic mobile unit... - Page 17 Automatic mobile unit recognition (AWK) Mobile unit coding strip Setting mobile unit coding 15 different codes can be set. They are To set or alter the coding of a mobile assigned to program places 1 to 15. unit with the AWK proceed as follows: Under "System function - Selector switch organization"...
- Page 18 Automatic mobile unit recognition (AWK) ^ Set the program place coding. ^ Place the track in the holder of the mobile unit and screw firmly in place. The magnetic strip on the G 7836 must have grey magnets. ^ Put the magnetic strip back in the track.
-
Page 19: Use
Preparing the items for The machine can be fitted with a variety of mobile units, baskets and inserts, cleaning depending on the cleaning application – Are the items to clean correctly in question. sorted and connected? The diversity of these units and inserts is so great that it is not possible to –... - Page 20 ^ Tall, narrow pieces should be placed Note in the center of the baskets. This ^ Load the items to be washed so that ensures good water coverage. water can access all surfaces. This ^ Mobile units and baskets with an ensures that they are properly cleaned.
-
Page 21: Spring Adapter Water Connection
Spring adapter water Height adjustable top basket connection The upper basket can be adjusted above and below the middle position Make sure that the spring adapter for " (2 cm). the water connection engages correctly when a basket or injector unit is Depending on the position of the upper inserted in the machine. -
Page 22: Applications
Applications Laboratory glassware (LG) Note ^ Petri dishes and the similar should be Wide necked glassware, wide necked Erlenmeyer flasks and petri dishes or placed in the correct insert with the glassware with a cylindrical form, soiled side facing the center. e.g. -
Page 23: Adding Of Liquid Cleaning Agents
Adding of liquid cleaning agents Additional DOS modules (optional): Use only cleaning detergents – Dispensing system DOS 2 (white) and neutralizers specially designed dispenses acid media such as a for labwashers and regard the neutralizing agent. application recommendations of the The dosing rate is 20 ml/min. -
Page 24: Preparing The Dos Dispensers
Adding of liquid cleaning agents Preparing the DOS dispensers When commissioning or when the The agents can be filled into 5 l plastic message "CHECK DISPENSING containers, which are color coded for SYSTEM..." appears, start the the relevant dispensing system. DOS-FILL program to prime the When commissioning, or when the dispensing system (see "Priming the... - Page 25 Adding of liquid cleaning agents Filling the containers with The relevant message goes out once the storage containers have been filled. liquid cleaning agents ^ Turn the machine off. Refill the container(s) as soon as the FILL CONTAINER DOS 1 and/or DOS 2, 3, 4 message appears in the display.
-
Page 26: Priming The Liquid Dispensing Systems
To ensure safe function the following later if one or more containers have maintenance should be carried out by a been allowed to empty, the dispensing Miele Service Technician at specified system(s) for liquid agents must be intervals. vented. Every 12-18 months: ^ Press the ON/OFF I-0 button. -
Page 27: Use
To change operating level There are four operating levels available: ^ Press 1 and 2 at the same time. A = Fixed and free access programs Operating levels A B C D will appear in the display. B = Free program selection ^ Select the operating level you want C = AWK –... -
Page 28: Starting A Program
Programming Manual supplied with With operating level "B" there are three the machine for detailed information possibilities for program selection. and important notes on the Miele 1. Program places 1 - 23 can be default programs. selected using the Program selector. -
Page 29: Program Sequence
Program sequence C. AWK – Automatic mobile unit recognition After being started the program ^ Select operating level "C". proceeds automatically. It is finished when PROGRAM END appears in the ^ Push the mobile unit with the coding display and the background lighting flashes (press any button to turn off the flashing lights). -
Page 30: Cancelling A Program
Cancelling a program ^ Select >CANCEL< with the 1 cursor button. The cursor > < flashes. A program can only be canceled in ^ Press the "Start" 6 button. The the operating levels B or D. program is canceled and the water is pumped away. -
Page 31: Interrupting A Program
Interrupting a program ^ Rearrange the load. Follow infection control regulations and wear A program can only be interrupted in protective gloves. the operating levels B or D. ^ Carefully close the door. If the door needs to be opened in If there is a lot of hot water in the extreme cases, e.g. -
Page 32: Serial Interface
Programming Manual. d Fault protocol Various printers can be used as external printers: – Epson-compatible (contact Miele for a list of suitable models) – HP LaserJet The address of the 9-pole pin sub-D plug of the serial interface cable: 5GND (ground) -
Page 33: Maintenance
Periodical maintenance for this Part of the maintenance is a function washer/disinfector must be carried out check: by Miele Technical Service after 1000 – A program is run as a test operating hours or every 6 months. – A thermoelectrical measurement The maintenance covers the following: –... -
Page 34: Process Validation
Maintenance Process validation Routine checks The standard process of cleaning and The routine checks must be done daily disinfection must be ensured by the by the user before using the machine. user as a routine matter. For the routine checks a checklist is equipped with the washer. -
Page 35: Cleaning And Care
Cleaning and Care Cleaning the coarse filter Wear protective gloves and goggles when cleaning this machine. Cleaning the filters in the wash cabinet The machine must not be used without all the filters in place! The filter combination in the base of the wash cabinet should be inspected daily and cleaned if ^ Press the two tabs together, remove... - Page 36 Cleaning and Care Cleaning the fine, flat and micro-fine filters ^ Remove the coarse filter. ^ Remove the fine filter from between the flat and micro-fine filters. ^ Then remove together with the flat filter. ^ Clean the filters. ^ Replace the filter combination in reverse order.
-
Page 37: Cleaning The Spray Arms
Cleaning and Care Cleaning the spray arms ^ Unscrew the upper spray arm. ^ Loosen the knurled nut of the lower The spray arms can get clogged. Check daily and clean if necessary. spray arm and remove. ^ Use a sharp pointed object to push Removing the spray arms particles into the spray arm jets and ^ Remove the baskets. -
Page 38: Cleaning The Control Panel
The wash cabinet is mostly self damp cloth or with a glass/plastic cleaning. cleaner. To disinfect use an approved If deposits have built, call Miele for info. cleaning agent. Cleaning the door seal Do not use abrasive or all purpose cleaners! They will damage Clean the door seal regularly with a the surface. -
Page 39: Mobile Units, Baskets And Inserts
Cleaning and Care Mobile units, baskets and inserts To ensure the function of mobile units, baskets and inserts, they must be checked daily. A checklist is supplied with the machine. Check the following points: – Are the rollers in a proper condition and are they securely fixed at the mobile unit/insert? –... -
Page 40: Cleaning The Water Inlet Filters
Cleaning and Care Cleaning the water inlet filters Cleaning the filter ^ Disconnect the machine from To protect the water inlet faucet, filters are incorporated in the intake hose electricity (unplug it or "trip" the attached to the water supply. If the circuit breaker). -
Page 41: Drying Unit (Ta)
Cleaning and Care Drying unit (TA) Changing the coarse filter The coarse filter should be changed when the message CHANGE COARSE FILTER flashes in the display. ^ Open the door of the storage cabinet. ^ Change the coarse filter. The soft filter side must face the front. -
Page 42: Replacing The Hepa-Filter
FILTER flashes in the display. 63, but they can be moved to other program places. See "System This filter should only be functions" in the Programming changed by a Miele Service Manual. Technician. To ensure the machine operates correctly, use original Miele HEPA filters only. -
Page 43: Report Printer (Option)
Miele. inside of the front panel). ^ Guide the paper through the slit of the front panel. Shut the front panel. Replacement paper rolls, 2 ¼" (58 mm) wide, outer diameter approx. 2" (50 mm) can be obtained from Miele. -
Page 44: Frequently Asked Questions
In the event of any problems CABINET HEATING" is displayed (water which cannot be corrected, please has not heated up in the wash cabinet contact the Miele Technical Service and the program takes too long): Department. ^ Isolate and correct the cause of the Messages regarding the operating problem. -
Page 45: After Sales Service
After sales service Should you have any difficulties please contact the Miele Technical Service Department. See back cover for contact information. ^ Please quote the model and serial number of your machine. This information can be found on the data plate (see also "Electrical... -
Page 47: Installation Instructions
INSTALLATION INSTRUCTIONS... -
Page 48: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of an old appliance materials Old appliances may contain materials that can be recycled. Please contact The cardboard box and packing your local authorities about recycling in materials protect the appliance during your area. -
Page 49: Installation
Installation Leveling the legs ^ Please refer to the installation diagram supplied with the Any unevenness in the floor can be machine. compensated for and the height of the machine raised or lowered by adjusting Furniture and fittings installed near the four screw feet. -
Page 50: Electrical Connection
^ Unscrew plinth facing (screws b). A damaged power cord must only ^ Remove plastic protective cap. be replaced with a genuine Miele Reassembling the service panel cord by a Miele service technician. ^ Replace the plastic protective cap,... -
Page 51: Plumbing
Plumbing Water connection The machine cannot be operated with an inflow pressure of less than 10 psi. This machine must be connected to The machine is supplied with the water supply in accordance with 3 connection hoses 5 ft. (1.5 m) long all national and local plumbing with "... - Page 52 A feed pump must be installed by Miele's Technical Service Dept. The discharge nipple of the DI water container (pressureless) must be at...
- Page 53 – The machine should preferably be connected to a separate drainage system onsite. If separate drainage is not available, contact your Miele application specialist for advice. The on-site connection needs to be between 2 ft. (0.6 m) and 3 ft 3" (1 m) high measured from the lower edge of the machine.
-
Page 54: Technical Data
Technical Data Height: " (117.5 cm) Width: " (90 cm) Depth: 27 ½" (70 cm) Depth with the door open: " (126.5 cm) Connection data: see data plate Power cord approx. 5' 11" (1.8 m) Water temperature: Hot, cold and DI water connection max. - Page 55 Technical Data Surrounding temperature: between 41°F - 104°F (5°C to 40°C) Height above sea level: up to 1640 yards (1500 m)* Noise level in dB (A) Sound pressure level LpA: less than 70 Test marks: interference suppression !-mark: MPG-Guidelines 93/42/EWG, Class IIa *If the machine is installed at a location above 1500 m, the boiling point of the wash water is reduced.
- Page 56 All rights reserved / 3106 M.-Nr. 06 868 470 / 00 en - US...