Page 1
Baker Owner’s Manual Models WB1E, WB2E, and BWB1SE This manual includes material related to installation, use , cleaning, and care. Exploded view[s], as well as any available parts list[s] and wiring diagrams pertaining to the unit covered by this manual are also included.
Page 2
Wells products. This warranty is void if it is determined that, upon inspection by an authorized service agency, the equipment has been modifi ed, misused, misapplied, improperly installed, or damaged in transit or by fi re, fl ood or act of God.
TABLE OF CONTENTS Warranty General Information and Installation 1–2 Specifications Daily Operation Cleaning WB1E Exploded View and Parts List 6–7 WB2E Exploded View and Parts List 8–9 BWB1SE Exploded View and Parts List 10–11 Wiring Diagrams 12–14...
Page 5
Using any part other than genuine Wells factory supplied parts relieves the manufacturer of all liability. Due to periodic changes in designs, methods, procedures, policies, and regulations, the specifi cations contained in this document are subject to change without notice.
GENERAL SAFETY INFORMATION This equipment is designed and sold for commercial use only, and is intended for use by personnel trained and experienced in its operation. This is not sold for consumer use in and around the home nor for use directly by the general public in food service locations. Before using your new equipment, read and understand all the instructions and labels associated with the unit prior to putting it into operation.
ELECTRICAL PLUG LOCATION [VIEWED FROM FRONT] MODEL FROM FROM BOTTOM LEFT SIDE WB2E shown (mm) (mm) BWB1SE (16) (130) WB1E (117) (124) WB2E (117) (124) LEG DISTANCE FROM OUT- SIDE OF BODY MODEL FRONT BACK SIDE 13.5 in. HEIGHT (343 mm)
DAILY OPERATION SETTING THE TIMER CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD BE TAKEN WHILE To increase or decrease the pre-set timer duration, USING THIS UNIT. press and hold either the ▲ or ▼ button and while holding, press the “START/STOP”...
CLEANING DO NOT IMMERSE THE UNIT IN WATER OR LET THE UNIT STAND IN WATER. SUGGESTED CLEANING SUPPLIES i. mild dish detergent and water DO NOT HOSE DOWN THE UNIT OR ii. plastic scouring pad THE TABLE/COUNTER IF THE UNIT iii.
Page 11
WB1E PARTS LIST REF NO PART NUMBER DESCRIPTION QTY PAGE NO B8-35552 solid curved conduit 2F-30329 solid straight conduit 2C-30222 retaining ring 2F-30322 hinge 2V-30328 hinge pivot cap 2P-38628 upper grid cap 2C-31053 8-32 keps nut 2F-30327 cast top housing...
Page 13
WB2E PARTS LIST REF NO PART NUMBER DESCRIPTION QTY PAGE NO B8-35552 solid curved conduit 2F-30329 solid straight conduit 2C-30222 retaining ring 2F-30322 hinge 2V-30328 hinge pivot cap 2P-38628 upper grid cap 2C-31053 8-32 keps nut 2F-30327 cast top housing 2R-30335 handle 2C-31715...
Page 15
BWB1SE PARTS LIST REF NO PART NUMBER DESCRIPTION QTY PAGE NO B8-WL0620 body 2J-Z7497 control board 2E-35127 rocker switch B8-42003 bottom panel 2C-31715 8-32 x 0.3125-inch screw 2C-31053 8-32 keps nut 2E-Z5375 terminal block 2C-33935 #6 x 0.3125-inch screw 2A-40564 rubber foot B8-Z18949 rear panel...
WB1E WIRING DIAGRAMS UPPER HEATING ELEMENT 120 V SWITCH 10VAC TEMP. PROBE TRANSFORMER LOWER TERMINAL HEATING BLOCK **LOWER GROUND ELEMENT UPPER WIRE NOT USED HEATING ON WB1E ELEMENT WHITE 230 V BLACK GREEN 240 V COUPLER SWITCH 10VAC TEMP. PROBE...
Page 17
WB2E WIRING DIAGRAMS UPPER HEATING ELEMENT UPPER HEATING SWITCH SWITCH ELEMENT 10VAC 10VAC 120 V TEMP. TEMP. PROBE PROBE TRANSFORMER TRANSFORMER **LOWER GROUND **LOWER GROUND LOWER LOWER WIRE NOT USED HEATING WIRE NOT USED HEATING ELEMENT ON WB2E ON WB2E ELEMENT TERMINAL BLOCK...
Page 18
WIRE NOT USED ON WB1E UPPER HEATING WHITE ELEMENT BLACK 230 V GREEN 240 V COUPLER SWITCH 10VAC TEMP. PROBE 208/240V TRANSFORMER LOWER HEATING **LOWER GROUND ELEMENT TERMINAL WIRE NOT BLOCK USED ON WB1E 220/240V TRANSFORMER WHITE (SIDE VIEW) GREEN BLACK...