Generac Power Systems 004812-3 Owner's Manual page 45

ITEM PART NO.
1 0D5825
2 0E1142
3 0A8240
4 098184
5 0D9220
6 0E2911
7 049721
8 022097
9 0D58250526
10 0D7034
11 0E3677
12 0E3427
13 0D2244M
14 0E3101
15 044117
16 065317
17 0D4739
18 053666
21 042574
23 076466
24 046526
25 048527
26 071623
27 057642
28 022131
29 043107
30 022129
31 022145
32 046579
33 0E2463
34 0E2464
35 053667
36 0D9380
37 0A6751
38 0E3093
39 082507
40 0E2907
41 049954
42 047411
43 022473
44 036409
45 049813
46 051756
47 0E2423
48 * 082982
49 0E5029
50 * 0E2619C
51 099305B
52 025065
53 0E6785
54 0E6786
55 0E6787
56 * 055934H
57 * 055934N
58 * 055934C
* NOT SHOWN
** REFERENCE OF POSITION - SHOWN ON ENGINE HEATER EXPLODED VIEW.
Section 7 — Exploded Views and Parts Lists
QTY. DESCRIPTION
1 ENGINE 3.9L MITSUBISHI
1 ADAPTER FLYWHEEL HSG. MACHINED
2 FLEX PLATE SAE10
1 FAN COOLING 26"
1 SPACER FAN 3.9L 100K
1 ARM THROTTLE CONTROL
1 SCREW HHC M6-1.0 X 35 G8.8 BLK
4 WASHER LOCK M6-1/4
REF. JOINT,ENG OIL PRESSURE GAUGE (COMES WITH ENGINE)
REF. GASKET ENG OIL LINE 16.0
1 BOLT BANJO M14-1.5 W / 1/8-27 NPT
2 FITTING 3/8-19 BSP-3/8 BARB
1 ASSY MAGPICKUP (3/8-24 MALE)
1 ADAPTER MAG PICK UP
1 BARBED STR 3/8 NPT X 5/8
1 FITTING OIL DRAIN M18-1.5
1 WASHER FLAT M18 COPPER 1.5THK
1 SENDER OIL PRESSURE
1 ADAPTOR 1/8 NPTF TO 1/8-28
1 SWITCH OIL PRESSURE N/O 4PSI
34 WASHER LOCK M10
8 SCREW SHC 3/8-16 X 3/4 G8.8 NZ
12 SCREW SHC M10-1.5 X 55 G12.9
12 SCREW HHC M10-1.5 X 40 G8.8
14 WASHER FLAT 3/8-M10 ZINC
4 SCREW HHC M8-1.25 X 25 G8.8
8 WASHER LOCK M8-5/16
4 WASHER FLAT 5/16-M8 ZINC
4 SCREW SHC M8-1.25 X 60 G12.9
1 GASKET THERMOSTAT CASE
1 GASKET THERMOSTAT COVER
1 SENDER WATER TEMP
1 ADAPTER 1/8 NPT TO M16-1.5
1 SW-TMP 245 DEG 3/8 NPT
1 SOLENOID ASSY 24V SEALED CONN
1 STGHT TYP SWVL .25-28
1 BRACKET MOUNTING SHUT-DN SOLND
1 BALL JOINT 1/4-28 R/H
2 SCREW HHC M6-1.0 X 16 G8.8
2 WASHER FLAT 1/4-M6 ZINC
3 NUT HEX 1/4-28 STEEL
2 NUT HEX M6 X 1.0 G8 YEL CHR
2 SCREW HHC M10-1.5 X 20 G8.8
1 THERMOSTAT HSG REWORKED 3.9L
2 RELAY CONTACTOR 24VDC
1 SNUBBER BRASS 1/8" NPT
1 HARNESS ENG 3.9L SEALED E S GV
1 VALVE BALL 3/8 NPT
1 NIPPLE PIPE 3/8 NPT X 1-1/2
1 BANJO FITTING 14MM W/ 3/8" NPT
1 HOSE ASSEMBLY STEEL BRAIDED
1 VALVE CHECK
2 CLAMP VINYL .62 X .406 Z
1 CLAMP VINYL 1.31 X .281 Z
1 CLAMP VINYL .5 X .406 Z
Standby Generator Sets
Engine Parts – Drawing No. 0E6642-F
43