Table of Contents
Advertisement
• For foam filter elements:
Wash the element in warm water and
mild detergent several times. Rinse.
Squeeze out excess water and allow it to dry
completely. Soak the filter in lightweight oil
briefly, then squeeze out the excess oil.
Spark plug Maintenance
1. Disconnect spark plug cap from end of plug.
Clean out debris from around spark plug.
2. Using a spark plug
wrench, remove
the spark plug.
3. Inspect the spark plug:
If the electrode is
oily, clean it using a
clean, dry rag. If the
electrode has deposits
on it, polish it using
emery paper. If the white insulator is cracked or
chipped, the spark plug needs to be replaced.
nOtice: Using an incorrect spark plug may
damage the engine. See the Specifications chart
for your Generator for the type and gap required.
Storage
When the equipment is to remain idle for longer than
20 days, prepare the Engine for storage as follows:
1. cLeaninG:
Wait for Engine to cool, then clean Engine with
dry cloth. nOtice: Do not clean using water.
The water will gradually enter the Engine
and cause rust damage. Apply a thin coat
of rust preventive oil to all metal parts.
2. FueL:
To protect the fuel tank during storage, fill the
tank with gasoline that has been treated with
a fuel stabilizer additive. Follow fuel stabilizer
manufacturer's recommendations for use. Refer
to Checking and Filling Fuel on page 9.
WarninG! tO preVent SeriOuS
inJury FrOM Fire:
Fill tank in a well‑ventilated area away from
ignition sources. If the engine is hot from
use, shut the engine off and wait for it to
cool before adding fuel. Do not smoke.
3. LuBricatiOn:
a. Change engine oil.
b. Clean out area around spark plug.
Remove spark plug and pour one tablespoon of
engine oil into cylinder through spark plug hole.
Page 16
Spark plug
cylinder
assembly
For technical questions, please call 1-888-866-5797.
3. Install the cleaned filter. Secure the
Air Cleaner Cover before use.
4. When installing a new spark plug, adjust
the plug's gap to the specification on the
Specifications chart. Do not pry against the
electrode, the spark plug can be damaged.
5. Install the new spark plug or the cleaned spark plug
into the engine. Gasket‑style: Finger‑tighten until
the gasket contacts the cylinder head, then about
1/2‑2/3 turn more.
Non‑gasket‑style: Finger‑tighten until the plug
contacts the head, then about 1/16 turn more.
nOtice: Tighten the spark plug properly. If
loose, the spark plug will cause the engine
to overheat. If overtightened, the threads
in the engine block will be damaged.
6. Apply dielectric spark plug boot protector
(not included) to the end of the spark
plug and reattach the wire securely.
c. Replace spark plug, but leave
spark plug cap disconnected.
d. Pull Starter Handle to distribute oil in cylinder.
Stop after one or two revolutions when you
feel the piston start the compression stroke
(when you start to feel resistance).
4. StOraGe area:
Cover and store in a dry, level, well‑ventilated
area out of reach of children. Storage area should
also be away from ignition sources, such as
water heaters, clothes dryers, and furnaces.
nOtice: During extended storage periods the
Engine must be started every 3 months and allowed
to run for 15 – 2 0 minutes or the Warranty is VOID.
5. aFter StOraGe:
Before starting the Engine during or after
storage, keep in mind that untreated gasoline
will deteriorate quickly. Drain the fuel
tank and change to fresh fuel if untreated
gasoline has been sitting for a month, if
treated gasoline has been sitting beyond the
fuel stabilizer's recommended time period,
or if the Engine does not start.
ITEM 69674
Advertisement
Table of Contents
