Content of this Manual Note: The BDP9000 will be serviced on a modular level only. Faulty modules will be identified and replaced. Detailed circuit diagrams and technical information on a component level are therefore not provided in this document. 1.1.1.
Safety regulations require that after a repair, the set must be returned in its original condition. • Before returning the BDP9000 to the customer always do a safety check. Pay attention to the built-in protective devices, leakage current and insulation resistance.
Page 4
• Use only lead-free soldering tin Philips SAC305 with order code 0622 149 00106. If lead-free solder paste is required, please contact the manufacturer of your soldering equipment. In general, use of solder paste within workshops should be avoided because paste is not easy to store and to handle.
Required Equipment List BDP9000 EN 13 Required Equipment List Equipment & Facilities • Remote control (Blu-ray version) • Stereo Headphones (with 6.3 mm Jack Plug) • External audio amplifier with the following connections: audio L/R cinch inputs (x2) coaxial SPDIF input...
EN 14 BDP9000 Diagnosis and Repair Flowchart Diagnosis and Repair Flowchart 6.1. Overview Symptom Refer to No power detected (Standby LED off) Flowchart 1 No digital audio output Flowchart 2 No audio output Flowchart 3 Disc loading error Flowchart 4...
Diagnosis and Repair Flowchart BDP9000 EN 15 6.2. Flowchart 1: No power detected (Standby LED off) NO Power Detected (Stand by LED OFF) Change fuse F01 is normal? C10 voltage Change BD01 is normal voltage? Switching operation Check 2st voltage...
EN 16 BDP9000 Diagnosis and Repair Flowchart 6.3. Flowchart 2: No digital audio output There's no Digital Audio Out Check the A/V Receiver Check Current Digital Audio Set to Bitstream can Decode Current Setting is PCM. Bit-Steam Check the Audio Data at...
Diagnosis and Repair Flowchart BDP9000 EN 17 6.4. Flowchart 3: No audio output There is no Audio Output Check the passive parts around Check he audio signal Audio Jack pin at AIC 6,7,8 Check all the signal at Check the AIC1...
EN 18 BDP9000 Diagnosis and Repair Flowchart 6.5. Flowchart 4: Disc loading error Disc Ioading error Are Main and deck Check the power power OK? (5v, 12v) Is the 40pin FFC cable(between main & deck) Reinsert FFC cable correctly inserted correctly?
Diagnosis and Repair Flowchart BDP9000 EN 19 6.6. Flowchart 5: Remote control does not work Remote control does not work Remocon battery Change the battery Is the FFC cable(between Re-insert FFC cable correctly Front panel&Main) OK? U16(Pin5) Check the U16, R379 or change...
EN 20 BDP9000 Diagnosis and Repair Flowchart 6.7. Flowchart 6: No picture No Picture Logo screen is OK ? NO LOGO BD playback picture is OK ? DVD playback picture is OK ? Clock and data output from U14, X1 check for soldering error...
Diagnosis and Repair Flowchart BDP9000 EN 21 6.8. Flowchart 7: No logo screen (HDMI) NO LOGO Screen(HDMI) Video selection set properly Check the Video select, cable accords with cable connection connection, TV input mode and TV mode ? Clock, data and...
EN 22 BDP9000 Diagnosis and Repair Flowchart 6.9. Flowchart 8: No logo screen (Component 1080i, 720p, 480p) NO LOGO Screen (Component 1080i, 720p, 480p) Video selection accords with cable Check the Video select, cable connection and TV mode ? connection, TV mode...
Diagnosis and Repair Flowchart BDP9000 EN 23 6.10. Flowchart 9: No logo screen (Component 480i) NO LOGO Screen(Component 480i) Video selection Check the Video select, cable accords with cable connection connection, TV mode and TV mode ? Clock, data and...
Page 24
EN 24 BDP9000 Diagnosis and Repair Flowchart 6.11. Flowchart 10: No logo screen (Video, S-Video) NO LOGO Screen(Video, S-Video) Video selection accords Check the Video select, cable with cable connection connection, TV mode and TV mode ? Clock, data and...
Diagnosis and Repair Flowchart BDP9000 EN 25 6.12. Flowchart 11: BD TS Clock, data Check U1 power input and Memory and SYNC output from U1 ? (EL6, R342~344, R348) interface Clock, data and Check U30 power input and Memory SYNC output from U20 ?
Page 26
EN 26 BDP9000 Diagnosis and Repair Flowchart 6.13. Flowchart 12: DVD PS Clock, data and SYNC output from U1 ? Check U1 power input and Memory (EL6, R342~344, R348) interface Clock, data output from U20 ? Check U30 power input and Memory...
Software Update and Repair 7.1. Introduction To improve the performance of the BDP9000 Blu-ray Disc Player, Philips will release software updates. This section describes how to update the software on the BDP9000 Blu-ray Disc Player. 7.2. How to make an update disc? Download the software update from www.philips.com.
EN 28 BDP9000 Mechanical Instructions Mechanical Instructions 8.1. Removal of the top cover Remove the five screws (A, B, C). Lift the top cover. Figure 8.1-1...
Page 29
Mechanical Instructions BDP9000 EN 29 8.2. Removal of the front panel assembly Remove the top cover (refer to 8.1). Release the seven hooks (A, B, C, D) Release the front panel assy. (E). B(2x) D(3x) Figure 8.2-1...
Page 30
EN 30 BDP9000 Mechanical Instructions 8.3. Removal of the optical drive Remove the front panel assy. (refer to 8.2). Remove the four screws (A, B). Lift the optical drive (C). B(2x) A(2x) Figure 8.3-1...
Page 31
Mechanical Instructions BDP9000 EN 31 8.4. Removal of the SMPS PCB Remove the optical drive (refer to 8.3). Remove the six screws (A). Lift the SMPS PCB (B). A(6x) Figure 8.4-1...
Page 32
EN 32 BDP9000 Mechanical Instructions 8.5. Removal of the Main PCB Remove the optical drive (refer to 8.3). Remove the eleven screws (A, B). Lift the Main PCB (C). A(6x) B(5x) Figure 8.5-1...
Page 33
Mechanical Instructions BDP9000 EN 33 8.6. Removal of the memory card readers Remove the optical drive (refer to 8.3). Remove the two screws (A). Lift the memory card readers (B). A(2x) Figure 8.6-1...
Page 34
EN 34 BDP9000 Mechanical Instructions 8.7. Removal of the fan Remove the top cover (refer to 8.1). Remove the 2 screws (A). Remove the fan (B). A(2x) Figure 8.7-1...
EN 70 BDP9000 Spare Parts List 10. Spare Parts List 10.1. Cabinet assembly W348 W289 (3 x 8 Y) (3 x 10 Y) W289 (3 x 10 Y) P003 W289 W289 (3 x 10 Y) (3 x 10 Y) C015...
Page 72
Exchangeable versus Consumable Modules All faulty cables and modules must be stored by the service center for a minimum of two months. In that period Philips has the opportunity to ask for shipment to a central location for further analysis. After that period the faulty items may be disposed of in an appropriate manner.