Table of Contents
Advertisement
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
7,8
16 • TRAXXAS
TRAXXAS TQ
2.4GHz RADIO SYSTEM
i
USING THE RADIO SYSTEM
The TQi Radio System has been pre-adjusted at the factory. The
adjustment should be checked before running the model in case of
movement during shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.
3. Plug the battery pack in the model into the speed control.
4. Press and release the EZ-Set button on the speed control to
turn the model on. The speed control's LED will glow red. To
turn the speed control off, press the EZ-Set button until the LED
turns off. Note: If the LED shines green after the speed control is
turned on, Low-Voltage Detection is activated. This may cause
poor performance from NiMH battery packs. Make sure to turn
the Low-Voltage Detection on when using LiPo batteries. Never
use LiPo batteries while Low-Voltage Detection is turned off.
See page 18 for more information.
5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.
6. When looking down at the
model, the front wheels
should be pointing straight
ahead. If the wheels are
turned slightly to the left
or right, turn off TSM (see
page 17) and slowly adjust
the steering trim control
on the transmitter until they are pointing straight ahead; then,
return the multi-function knob to the desired TSM setting.
7. Gently operate the throttle trigger to ensure that you have
forward and reverse operation, and that the motor stops when
the throttle trigger is at neutral. Warning: Do not apply full
throttle in forward or reverse while the model is elevated.
8. Once adjustments are made, turn off the receiver on your model,
followed by the hand-held transmitter.
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach
the farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem
with the radio system or any external interference with your
radio signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At 60mph, a model can cover 88 feet every
second! It's a thrill, but use caution to keep your model in range. If
you want to see your model achieve its maximum speed, it is best
to position yourself in the middle of the car's running area, not
the far end, so you drive the car towards and past your position. In
addition to maximizing the radio's range, this technique will keep
your model closer to you, making it easier to see and control.
No matter how fast or far you drive your model, always leave
adequate space between you, the model, and others. Never drive
directly toward yourself or others.
TQi Binding Instructions
For proper operation, the transmitter and receiver must be
electronically "bound." This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: The receiver
must be connected to a 4.8-6.0v (nominal) power source for
binding, and the transmitter and receiver must be within 5 feet of
each other.
1. Press and hold the transmitter's SET button as you switch the
transmitter on. The transmitter's LED will flash red slowly.
Release the SET button.
2. Press and hold the receiver's LINK button as you switch on
the speed control (by pressing the EZ-Set button). Release the
LINK button.
3. When the transmitter and receiver's LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering
and throttle operate properly before driving your model.
Advertisement
Table of Contents
