Advertisement
Quick Links
Applicable Tire Diameter Capacity:
Gravity Mode :
Fixed Mode :
Dual Mode
Contact
MINOURA North American Tech Center
(for U.S. residents ONLY)
Hayward, California, U.S.A.
Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST)
Fax:
1-510-538-5899
Email: support@minourausa.com
indoor bicycle trainer
570 – 710mm
(22 – 29-inch)
610 – 710mm
(26 – 29-inch)
The LR961 can be used as a gravity trainer or a fixed position trainer by operating the lock
lever.
Fixed Mode acts like a traditional trainer where the trainer stays in the same position and
the rear roller compresses the tire to achieve resistance. This is good for power training.
Gravity Mode supports the bicycle frame by the axle allowing the bike to move up and
down. Your body weight dictates contact with the roller naturally so no adjustment is needed
no matter what bike or tire you use. This also extends tire life.
If you need support, please first contact the shop you purchased this product from or contact
the distributor in your country for assistance. A list of our distributors can be found here:
http://www.minoura.jp/english/support/shop/distributor.html.
If you need further support, contact us at one of the places listed below.
instructions manual
MINOURA Japan Headquraters
(for ALL customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131
Fax:
+81-584-27-7505
Email: minoura@minoura.jp
Web:
www.minoura.jp
LR961
(ver.1.0 2017/1)
Made in Japan
Advertisement
Related Manuals for MINOURA LiveRide LR961
Summary of Contents for MINOURA LiveRide LR961
- Page 1 A list of our distributors can be found here: http://www.minoura.jp/english/support/shop/distributor.html. Made in Japan If you need further support, contact us at one of the places listed below. MINOURA North American Tech Center MINOURA Japan Headquraters (for U.S. residents ONLY) (for ALL customers) Hayward, California, U.S.A.
-
Page 2: Important Notes
The tools don't come in the kit, you need to prepare separetely. • Use the supplied rear quick release skewer for maximum stability. The hub clamping parts (couplings) fits the supplied quick release skewer only. Minoura is not responsible for any problem caused from using your own skewer. - Page 3 How To Setup LR961 Required Tool : 13mm open wrench (NOT a closed type) LR961 is packed in the folded condition. The pillars are folded backward, and the Mag resistance unit is folded forward. (see Fig. A) First, raise the pillars then set the Mag unit into position. Left Side Pillar Lock Pin Hole for Transporting Mode Lock Pin Hole for Fixed Mode...
- Page 4 Left Side Coupling Bolt Parts List for LR961 Drive Roller (for standard quick relaese skewer) Lock Nut Pivot Bolt Flywheel (becomes HOT after use) Roller Pressure Adjust Knob Hub Clamp Lever (Fig. D) Right Side Coupling Lever Cover How To Install Rear Wheel Hub Clamp Lever Left Side Coupling Bolt Lock Nut...
- Page 5 Now, grab the saddle of your bike and rock the bike back and forth to make sure your bike is securely in the trainer. Your bike should not move independently of the trainer where it is attached. Tighten the Lock Nut firmly to fix the left side coupling position. (see Fig. H) If you feel the clamp lever action is too tight, spray a silicon lublicant between the plated right side coupling steel tube and the gray plastic guide sleeve.
- Page 6 How To Use Gravity Mode In Gravity Mode, the pillars move freely by releasing the Lock Pin from the hole. The rear tire will be compressed to the drive roller at ideal pressure due to applying your weight including the bike weight automatically and directly. You don't need to micro adjust the roller pressure every time you set any bike on LR961 whatever the tire size is.
- Page 7 How To Use Fixed Mode In Fixed Mode, the bike will be supported at same height level at all times. Even you apply load to the rear wheel, the wheel position will not change. So you need to push the Drive Roller to the tire. Maintain the pressure to the tire in correct level.
- Page 8 How To Operate Remote Shifter LR961 comes with a convenient remote shifter device. By installing it on your handlebar or stem, you can adjust the resistance level in 13 levels without getting off the bike. The plastic band is soft enough to fit aero-shaped carbon handlebar or round shaped stem as well as the standard round dimension handlebars.