Roland System-8 Reference Manual page 15

Menu Parameter
[ K ] [ J ] [ K ] [ J ]
[SHIFT] +cursor Cursor
PartBalance
COMMON
Tempo Src
Perf Tempo
Valid when Tempo
*
Src=PERF
Arp Src
ARPEGGIO
Arp Dst
Prm Src
Ref Note
Src
Valid when Prm
*
Src=PERFORM
CV/GATE OUT
Bend Range
Valid when Prm
*
Src=PERFORM
Portamento
Valid when Prm
*
Src=PERFORM
PortTime
Valid when Prm
*
Src=PERFORM
Prm Src
INPUT Tempo Sync
Valid when Prm
*
Src=PERFROM
Value
[VALUE] knob
LW64–0–UP63
KNOB, PERF
40.0–300.0 (BPM)
LOWER, UPPER
LOWER,
UPPER,
UP&LW
SYSTEM, PERFORM
C0, C1, C2, C3, C4
ALL
KBD (L)
KBD (U)
KBD (U&L)
STEP SEQ (L)
STEP SEQ (U)
PATCH (L)
PATCH (U)
USB OMNI
USB CH1–USB CH16
MIDI IN OMNI
MIDI IN CH1–MIDI IN CH16
1–24
OFF
ALWAYS
LEGATO
0–127
SYSTEM, PERFORM
OFF, ON
Explanation
LW64:
LOWER only (UPPER does not sound)
0:
LOWER and UPPER have the same volume
UP63:
UPPER only (LOWER does not sound)
Selects whether the tempo setting follows the value of the
knob (KNOB) or the setting of the performance (PERF).
Specifies the tempo when the Tempo Src setting is
[SHIFT]
If you hold down the
*
knob, the value changes in 0.1 steps.
Selects the part that uses the arpeggio settings.
CHORD MEMORY also operates according to this setting.
Selects the part to which the arpeggio applies.
If you choose UP&LW, the arpeggio applies to both the upper
part and lower part.
CHORD MEMORY also operates according to this setting.
Selects whether the CV/GATE OUT setting follows the
system setting (SYSTEM) or the setting of the performance
(PERFORM).
In steps of an octave, specifies the note number for which CV
OUT is 0 V.
Keyboard (both upper and lower), step sequencer (both
upper and lower), USB (OMNI), and MIDI IN (OMINI) data are
output.
Keyboard performance data of the lower part is output.
Keyboard performance data of the upper part is output.
Keyboard performance data is output.
Step sequencer performance data of the lower part is
output.
Step sequencer performance data of the upper part is
output.
The behavior of the lower part's sound engine is output.
The behavior of the upper part's sound engine is output.
The note data of all USB MIDI channels is combined and
output.
The note data of a specified USB MIDI channel is output.
The note data of all MIDI IN channels is combined and
output.
The note data of a specified MIDI IN channel is output.
Specifies the amount (in semitone units, up to two octaves)
of pitch change that occurs when you move the pitch bend
lever.
Portamento is not applied.
Portamento is always applied.
Portamento is applied when you hold down a key and press
another key.
When portamento is used, this specifies the time over which
the pitch will change.
Select whether the INPUT setting follows the system setting
(SYSTEM) or the setting of the performance (PERFORM).
If this is "ON," the INPUT effect's delay time (TIME) is
synchronized to the tempo.
If Prm Src = PERFORM, you can turn this on/off by holding
*
down the [VOCODER] button and pressing the
SYNC] button.
Editing a Performance
"PERF "
[VALUE]
button and turn the
[TEMPO
15