Related Manuals for Slant/Fin EC-25
Summary of Contents for Slant/Fin EC-25
-
Page 1: Assembly Instructions
EUTECTIC EC-20 OIL-FIRED WATER BOILERS/NO. 2 OIL ASSEMBLY INSTRUCTIONS EUTECTIC EC-20 SSEMBLY GUIDE ©Slant/Fin Corp. 2013 • Printed in the U.S.A. 1113 • Part # 470911000 • Publication No. EC-20-50 Rev.B... -
Page 2: Package List
Contains the control panel instructions 8800N075A 8800N073A 8800N043A Control Panel Boiler Boiler Casting Sub-Assembly Jacket and Insulation Basic or SF-10 for EC-20 Series Basic – 475014000 EC-25 475002000 475009200 SF-10 – 475299000 Basic – 475014000 8800N073A EC-26 475003000 4750010200 SF-10 – 475299000 8800N075A Basic –... -
Page 3: Step 1- Mounting Feet
Tools required: • 1 Phillips screwdriver • 1 Wide flat screwdriver • 1 13mm open end wrench • 1 17mm open end wrench • 1 19mm open end wrench Step 1– Mounting Feet Boiler body assembly 1. Fit the adjustable feet to the height converter (The feet are delivered with the screw bag in the jacket and insulation package) EUTECTIC EC-20 SSEMBLY GUIDE... - Page 4 Step 2 Step 2 Mounting: Hinged door Boiler casting assembly is normally shipped with boiler door hinges on the right when viewing boiler from front. If boiler casting assembly has door removed, it can be mounted with hinges on the right side when viewing from the front by following the procedure below..
- Page 5 Step 3 Step 3 Adjusting the boiler door To adjust the boiler door, adjust the top hinge: Untighten screw A turn the screw B to position the door, Tighten screw A. EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 6 Step 4 Baffles Put the baffles in place. Align the convection accelerators with the first fins. Put the baffles in place. Align the convection accelerators with the first fins. EC-25 EC-26 EC-25 EC-27 EC-26 EC-28 EC-27 EC-28 Step 5 Close the boiler door and tighten using the 2 special nuts.
- Page 7 Step 6 Mounting: Front crosspiece with Basic or Thermatic Control Thermatic Basic EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 8 Step 7 Fitting the body insulation EUTECTIC EC-20 SSEMBLY GUIDE...
-
Page 9: Assembling The Burner
Step 8 Assembling the burner Fix the gasket with the flange on the burner door using four 3/8”–16 studs, supplied. (screw shorter length of metric thread into burner door.) Push the burner into the burner door until it will not go any further. Fix the burner using hex nuts, supplied. - Page 10 Step 9 Danger Label Rating Label Baffle Label Attach Burner Instructions Label that is packed with Burner EUTECTIC EC-20 SSEMBLY GUIDE...
-
Page 11: Fitting The Rear Panel
Step 10 Step 11 Fitting the rear panel Remove the clean out trap Remove the cleanout. EUTECTIC EC-20 SSEMBLY GUIDE the cleanout. - Page 12 Step 12 Fitting the rear panel - continued Fit the rear panel EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 13 Step 13 Replace the clean out trap Replace the clean out trap EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 14 Step 14 Control panel assembly – Installing sensor bulbs Then, insert the bulbs inside the pocket and maintain them with the spring - Detail B: Thermatic Control Panel Detail A: Basic Control Panels - Boiler thermostat - Boiler sensor - Boiler sensor - Safety thermostat - Safety thermostat - Thermometer...
- Page 15 Step 15 Fitting the front panel - Fitting the top panel Connect burner hanress to molex connector. Make sure it disconnects when opening door. See page 9 for adjustment if necessary. EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 16 EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 17 EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 18 EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 19 EUTECTIC EC-20 SSEMBLY GUIDE...
- Page 20 ©Slant/Fin Corp. 2013 • Printed in the U.S.A. • Part # 470911000 • Publication No. EC-20-50RevA SL NT/FIN CORPOR TION., Greenvale, N.Y. 11548 • www.slantfin.com Phone: (516) 484-2600 • Fax: (516) 484-5921 In Canada: Slant/Fin LTD/LTEE, Mississauga, Ontario • www.slantfin.can...