Kenwood KDC-W8534 Service Manual page 16

KDC-W8534/W8534Y
KDC-X790
Audio adjust mode
Model with DSP (KDC-W8534/W8534Y)
• By pressing [AUD] key for less than 1 second, the Audio
Adjust mode is entered.
• As with the [AUD] key, [∗] key on the remote controller can
be used to enter the Audio Adjust mode.
• As for the adjustment items, items for both the AUDIO
FUNCTION MODE and SETUP MODE are included.
• By pressing [AUD] or [FM] key briefly, switch the item to be
adjusted in the following order. (only in forward rotation)
• The initial item will be Fader and the next is Balance. (After
Balance, it will be arbitrary.)
• With the remote controller, continuous forwarding is pro-
hibited.
• Using the VOL knob and [
adjusted to the following 3 levels : R15 ↔ 0 ↔ F15 (The
default value : 0)
• Using the VOL knob and [
be adjusted to the following 3 levels : L15 ↔ 0 ↔ R15 (The
default value : 0)
• Using the VOL knob and [
set is to be adjusted to the following 2 levels : –8 ↔ 0 (The
default value : 0)
Model with no DSP (KDC-X790/MP732/MP8533)
• By pressing [AUD] key for less than 1 second, the audio
adjustment mode can be entered.
• Using the remote controller [∗] key and [AUD] key, the au-
dio adjustment mode can be entered.
• Adjustment items of both the AUDIO FUNCTION MODE
and SETUP MODE are included.
• By pressing [AUD] or [FM] key briefly, switch the item to be
adjusted in the following order. (only in forward rotation)
• The initial item will be Fader, which is followed by : Balance
→ Bass Level → Middle Level → Treble Level → HPF Front
→ HPF Rear → LPF Sub Woofer (After this, it will be arbi-
trary)
• With the remote controller, continuous forwarding is pro-
hibited.
• Using the VOL knob and [
adjusted in 3 steps : R15 ↔ 0 ↔ F15 (The initial value is 0)
• Using the VOL knob and [
be adjusted in 3 steps : L15 ↔ 0 ↔ R15 (The initial value is
0)
• Using the VOL knob and [
/ Treble Level can be adjusted in 3 steps : –8 ↔ 0 ↔ +8
(The initial value is 0)
16
TEST MODE
] / [ ] key, the Fader is to be
] / [ ] key, the Balance is to
] / [ ] key, the Volume Off-
] / [ ] key, the Fader can be
] / [ ] key, the Balance can
] / [ ] key, the Bass / Middle
• Using the VOL knob and [
Level can be adjusted in 3 steps : –15 ↔ 0 ↔ +15 (The
initial value is 0)
• Using the VOL knob and [
set can be adjusted in 2 steps : –8 ↔ 0 (The initial value is
0)
• Using the VOL knob and [
Rear can be adjusted in 2 steps : Through ↔ 180Hz (or
220Hz) (The initial value is Through)
• Using the VOL knob and [
Woofer can be adjusted in 2 steps : 60Hz (or 50Hz) ↔
Through (The initial value is Through)
• Using the VOL knob and [
set can be adjusted in 2 steps : –8 ↔ 0 (The initial value is
0)
• Using the VOL knob and [
ON/OFF can be adjusted in 2 steps : OFF ↔ ON (The
initial value is OFF)
• Using the VOL knob and [
can be adjusted in 2 steps : OFF ↔ ON (The initial value is
OFF)
• Bass f / Bass Q / Bass EXT / Middle f / Middle Q / Treble f
do no appear in audio adjustments.
MENU items
• Push the [ ] (NEXT) key for at least 1 second to enter the
MENU.
• The [DNPP/SBF] and [DIRECT] keys on the remote con-
troller can also be used to enter the MENU.
• With the remote controller, continuous forwarding is pro-
hibited.
• When a CD is used as a source, the default item will be the
ACD F/W Version.
(DXM-6800 mechanism equipped model : KDC-W8534/
W8534Y, KDC-X790)
2-ZONE (Dual Zone) items
• When using sources other than the STANDBY source, us-
ing a short-press on [AUTO] or [TI] key, 2-ZONE ON/OFF
is achieved.
Backup current measurement
When reset in Acc OFF (Back Up ON) condition, MUTE termi-
nal goes off after 2 seconds, instead of 15 seconds. (During
this time, the CD mechanism does not function.)
] / [ ] key, the Sub Woofer
] / [ ] key, the Volume Off-
] / [ ] key, the HPF Front /
] / [ ] key, the LPF Sub
] / [ ] key, the Volume Off-
] / [ ] key, the Loudness
] / [ ] key, 2-Zone ON/OFF