Sony BVP-550 Maintenance Manual page 489

Page Ver. Item
OTHERS 1 FILTER,
WHT MEM
NTSC ENC
ROTARY
OWN CALL
CENTER H POS
CENTER V POS
LENS VTR S/S
VF ? DISPLAY
PinP RET RVS
OTHERS 2 F TALLY RVS
1.07 BLK GAM
INHIBIT
CHAR CAM No. [1,2,3], A,B,C
1.10
1.10 WHT SETUP
MODE
1.10 AW SHADING
MODE
BVP-550
Settings Contents
[ON], OFF
ON : A total of 8 settings of the white balance value can be saved
OFF : One white balance value can be saved for the WHITE BAL
[WIDE], NRW
Sets the band width of the Q signal for the NTSC color encoder.
[STD], RVS
Selects the mode of MENU SEL switch (as turned counterclockwise
when viewed from the front.)
STD : Cursor moves downwards and a numeric value increases.
RVS : Cursor moves upwards and a numeric value decreases.
R, F&R , OFF Selects whether one or two TALLY lamps are lit corresponding to the
CALL button of camera adaptor pressed, or not. Or selects which
TALLY lamp is lit when the CALL button is pressed.
(This setting is valid in connection with CCU. When the camera is used
alone and MSU/RCP is not connected to the camera, it is always set to
OFF.)
R : Rear TALLY lamp is lit.
F&R : Rear and front TALLY lamps are lit.
OFF : No TALLY lamp is lit corresponding to the CALL button.
–20 to 20 ([XX]) Shifts horizontally the location of the center marker on the screen.
20 (right) ↔ –20 (left)
–20 to 20 ([XX]) Shifts vertically the location of the center marker on the screen.
20 (up) ↔ –20 (down)
TALK, [RET2]
Selects the mode of VTR S/S SW of the lens and camera.
TALK : VTR S/S SW of lens functions as INCOM TALK SW
RET2 : VTR S/S SW of lens functions as RET2 SW and that of the
[ON], OFF
Turns on and off the indication of ? mark at the top-right of the VF screen
with the DISP switch set to ON when the self-diagnosis result is NG (no
good) and so on.
[RVS1], RVS 2, OFF
Selects the indication mode of VF display in PinP mode. (Does not function
in the unit.)
[ON], OFF
Selects the operation mode of TALLY lamps corresponding to a CALL
button of MSU or RCP pressed when a TALLY signal is input to the camera
from CCU or VTR.
ON : Rear and front TALLY lamps go out.
OFF : Rear TALLY lamp alone goes out.
[ON], OFF
ON : Inhibits the black gamma adjustment and on/off function from the
OFF : Enables the above operation.
Selects the indication mode of the camera number set by the CAMERA
No. page of Operation menu.
1,2,3 : Indicates in numerics.
A,B,C : Indicates camera numbers 1 to 27 in alphabetical order of A to Z.
(When connecting 28 or more cameras, select "1,2,3".)
[AWB], LEVEL
AWB : After executing the LEVEL AUTO, white balance adjustment
LEVEL: After executing the LEVEL AUTO, white balance adjustment
[RGB], RB ONLY
RGB
RB ONLY : When automatically adjusting the white balance, R and B
in conbination with the CC filter and WHITE BAL switch settings.
switch setting A or B, for a total of 2 settings.
(momentary) and that of the camra as RET2 SW.
camera as INCOM TALK SW.
MSU or Paint manu.
data returns to the value before execution.
data changes to the value after the white balance is adjusted
using TEST 2 signal.
: When automatically adjusting the white balance, R, G, and
B signal waveforms are all flattened.
signal waveforms are flattened.
3-1. Setup Menu
3-1-6. System Config Menu
3-15(E)