Related Manuals for Honeywell HBD7S(X)
Summary of Contents for Honeywell HBD7S(X)
-
Page 1: Bullet Camera
HBD7S(X) Indoor/Outdoor Bullet Camera Configuration Guide Document 800-15429 – Rev A – 07/2013... - Page 2 2 | HBD7S(X) Camera Configuration Guide Revisions Issue Date Revisions 07/2013 New document. www.honeywell.com/security...
-
Page 3: Contents
Regulatory | 3 Regulatory FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 4: Warranty And Service
Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.323.4576 (North America) for assistance or to request a Return Merchandise... -
Page 5: Table Of Contents
Contents | 5 Contents Regulatory ........ -
Page 6: General Features
Defog Defog improves image definition in conditions of poor visibility, such as in fog, smoke, rain, or snow. Additional Functions • On-screen display menu with multi-language support • 8 privacy masking zones • 4 motion detection zones www.honeywell.com/security... -
Page 7: Configuring The Camera
Configuring the Camera | 7 Configuring the Camera Using the OSD Joystick The camera’s setup menus are controlled using the built-in OSD joystick located on the underside of the camera. Figure 1 OSD Joystick SET UP Press down and hold the OSD joystick for two seconds to bring up the OSD menu on the connected monitor. -
Page 8: Main Setup Menu
Set the desired BRIGHTNESS level. Select a value between 1 and 100. The default setting is 50. Set the MODE to INDOOR or OUTDOOR, depending on the camera environment. Select RETURN to save your settings and return to the SETUP menu. www.honeywell.com/security... -
Page 9: Exposure
Configuring the Camera | 9 Exposure In the SETUP menu, navigate to EXPOSURE, and then press the joystick to enter the EXPOSURE menu (see Figure Figure 4 Exposure Menu Shutter Set SHUTTER to one of the following: x256, x128, x64, x32, x24, x16, x14, x12, x10, x8, x6, x4, x2, AUTO (default), 1/60, FLK, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000, 1/20000, 1/50000, or 100000. -
Page 10: Backlight Compensation
If BLC is selected, do the following: Press the joystick to enter the BLC menu (see Figure Figure 6 BLC Menu Set VALUE to LOW, MIDDLE (default), or HIGH. Set the backlight compensation AREA manually or set it to the DEFAULT setting. www.honeywell.com/security... -
Page 11: D-Wdr
Configuring the Camera | 11 If AREA is selected, do the following: Press the joystick to enter the POSITION adjustment screen, and then adjust the position of the BLC area by moving the joystick up or down, left or right. Press the joystick again to enter the SIZE adjustment screen, and then adjust the size of the BLC area by moving the joystick up or down, left or right. -
Page 12: White Balance
Set BLUE to a value between 0 and 100. The default setting is 28. Set RED to a value between 0 and 100. The default setting is 16. Select RETURN to save your settings and return to the SETUP menu. www.honeywell.com/security... -
Page 13: Day&Night
Configuring the Camera | 13 Day&Night Picture can be displayed in either color or black and white. In the SETUP menu, navigate to DAY&NIGHT, and set it to AUTO (default), B/W, or COLOR. Mode Description AUTO The camera automatically switches between day (color) mode and night (black-and-white) mode, depending on the amount of ambient light. -
Page 14: 3Dnr
3DNR Menu Set the digital noise reduction LEVEL to a value between 0 and 200. The default setting is 200. Note High DNR levels may result in "ghosting." Select RETURN to save your settings and return to the SETUP menu. www.honeywell.com/security... -
Page 15: Special Menu
Configuring the Camera | 15 Special In the SETUP menu, navigate to SPECIAL, and then press the joystick to enter the SPECIAL menu (see Figure 11). Figure 11 Special Menu Camera Title You can select a camera title of up to 15 alphanumeric characters in length and display it on the monitor. -
Page 16: D-Effect
The mirror function flips the video image vertically or horizontally. Set MIRROR to OFF (default), MIRROR, V-FLIP, or ROTATE. Mode Description MIRROR The image is flipped horizontally. V-FLIP The image is flipped vertically. ROTATE The image is flipped both horizontally and vertically. www.honeywell.com/security... - Page 17 Configuring the Camera | 17 D-Zoom The digital zoom function can magnify the video image up to 32 times. The higher the magnification, the lower the resolution. Note SMART D-ZOOM and DIS functions are not available when D-ZOOM is enabled. Set D-ZOOM to OFF (default) or ON.
-
Page 18: Motion Detection
Press the joystick to enter the MOTION menu (see Figure 15). Figure 15 Motion Menu Select the motion detection AREA you want to configure (1, 2, 3, or 4). Set AREA DISPLAY to ON (default) or OFF to show or hide the selected area. www.honeywell.com/security... -
Page 19: Privacy Mask
Configuring the Camera | 19 If ON is selected, do the following: Press the joystick to enter the POSITION adjustment screen, and then adjust the position of the motion detection area by moving the joystick up or down, left or right. Press the joystick to enter the SIZE adjustment screen, and then adjust the size of the motion detection area by moving the joystick up or down, left or right. -
Page 20: Defect
For advanced users only. You can set up the camera to eliminate defective pixels (white spots) on the screen. In the SPECIAL menu, navigate to DEFECT, and then press the joystick to enter the DEFECT menu (see Figure 17). www.honeywell.com/security... -
Page 21: Defog
Configuring the Camera | 21 Figure 17 Defect Menu Set SENSE UP to x4, x8, x16, x32 (default), x64, or x128. It is recommended that you use the default setting x32. Set DIFF to define the size of the defect you want to eliminate. Select a value between 0 and 3. -
Page 22: Language
In the SETUP menu, navigate to ADJUST, and then press the joystick to enter the ADJUST menu (see Figure 18). Figure 18 Adjust Menu Sharpness You can set the sharpness of the video image. Set the SHARPNESS level. Select a value between 0 and 30. The default setting is 25. www.honeywell.com/security... -
Page 23: Monitor
Configuring the Camera | 23 Monitor You can optimize the video signal for your monitor. Set MONITOR to LCD (default), USER, or CRT, depending on the type of monitor you are using. Press the joystick to enter the LCD/USER/CRT menu. Set the desired GAMMA level. -
Page 24: Troubleshooting
Change the camera position, if necessary. Sense-Up does not work. Check that the AGC setting in the EXPOSURE menu is not set to OFF. Check the EXPOSURE menu and make sure SHUTTER is set to ----- (not a fixed shutter speed). www.honeywell.com/security... - Page 25 Troubleshooting | 25 800-15429 - A - 07/2013...
- Page 26 Document 800-15429 – Rev A – 07/2013 © 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects.