Honeywell HBD9 Quick Install Manual

HBD9 Series Camera Quick Install Guide
800-09587 Rev A 11/11

Camera Overview

Bracket
Mounting
Ring
Notch

Installing the Camera

HBD9 Series cameras (HBD92S/HBD92SX/HBD95S/HBD95SX) can be installed on a
wall or ceiling indoors or outdoors.

Mounting the Camera

1. Find a suitable location for mounting the camera. The mounting surface must be
flat and capable of supporting the combined weight of the camera, sunshield,
bracket, and mounting ring (approximately 3.18 lb. [1.44 kg]).
2. Attach the mounting ring to the mounting surface using the four supplied 1-inch
(25.4 mm) self-drilling screws.
3. Attach the camera and bracket to the mounting ring using the four supplied
3/8-inch (9.52 mm) socket cap screws. Tighten the screws using the supplied hex
key.
Note For an outdoor wall mount installation, ensure that the notch in the base of the bracket is
facing down.
Positioning the Camera
You can position the camera to capture the desired field of view by adjusting the multi-
directional bracket. To change the camera position, loosen the bracket screws with
the supplied hex key, reposition the camera, and then tighten the screws.

Connecting the Camera

1. Connect the camera's BNC video output to the video input on your monitor or
digital video recorder.
2. Connect the camera's 12 V DC power output to a power supply appropriate for
your installation (24 V AC or 12 V DC).
Figure 1 Video and Power Connections
Note When the main video is connected to a terminated monitor or recording device, if the
second video out is also connected to a terminated monitor, the video will become darker.
For correct video level, ensure that only one video output is terminated with a 75 ohm load.

Configuring the Camera

Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
Figure 2 Focus and Zoom Controls*
N
T W
* The HBD92S(2.8–12 mm) controls are shown here.
The controls appear in reverse order on the HBD95S (5–50 mm).
Document 800-09587 – Rev A – 11/11
Sunshield
Video (BNC) - Yellow
Power (12 V DC) - Red
Focus Adjustment Screw
Zoom Adjustment Screw
To set the focus:
1. Loosen the focus set screw using the supplied hex key.
2. Turn the focus adjustment screw clockwise for near focus (N) or
counterclockwise for far focus (
3. Tighten the focus set screw to lock the focus setting.
To set the zoom:
1. Loosen the zoom set screw using the supplied hex key.
2. Turn the zoom adjustment screw clockwise to decrease zoom (W) or
counterclockwise to increase zoom (T).
3. Tighten the zoom set screw to lock the zoom setting.
Setting the LED Brightness
You can adjust the LED brightness level in night (B/W) mode. The LED brightness
control is located on the underside of the camera, next to the focus and zoom
controls. Unscrew the cap to access the control board.
Figure 3 Camera Control Board
VIDEO
TEST
SETUP
LED LEVEL
To set the LED brightness:
Turn the LED LEVEL adjustment screw either clockwise to increase the LED
brightness or counterclockwise to decrease the LED brightness.

Programming the Camera

You can program the camera using the onscreen display (OSD) menus. The menu
controls are located on the camera control board
joystick up, down, left, or right to navigate through the menu options. Press the
joystick to execute (set) a selection or to enter a submenu (
Figure 4 Setup Menu Structure
Main Setup Menu
<<SETUP MENU>>
1 LENS DC
2 EXPOSURE
3 WHITE BAL ATW
4 SSDR OFF
5 BACKLIGHT OFF
6 DNR3 ON
DAY/NIGHT EXTERN
7
8 SPECIAL
9 EXIT SAVE
∞
).
2nd Video Out
OSD Controller
LED Adjustment Screw
(Figure 3). Move the OSD controller

).
Submenu Menu Options
LENS DC
EXPOSURE
BRIGHTNESS, SHUTTER, AGC,
SENS-UP, RETURN
WHITE BAL ATW, OUTDOOR, INDOOR,

MANUAL, AWC SET
SSDR OFF, ON
BACKLIGHT OFF, BLC, HLC
DNR3 ON, OFF
EXTERN, COLOR, B/W, AUTO
DAY/NIGHT
SPECIAL See Special Menu Structure.