Page 1
START Click the button and follow the instructions. CATEYE V3n CC-TR210DW/TR310TW Quick Start...
Page 2
Thank you for purchasing our cyclocomputer CATEYE V3n. This Quick Start Manual explains how to set up the computer, how to install the unit to your bicycle, and how to wear the heart rate sensor. Please set up the unit according to the specified procedure, then it will be ready for use as a cyclocomputer.
Page 3
This PDF contains a movie file. When you click on the movie screen, a message regarding security appears. Click the “Trust in the text” or “Play” button to close the message. Click the screen again to play the movie. Next...
CATEYE V3n Return to a Cover Quick Start Manual Contents Click the item you wish to view. Setting up the computer How to install the bracket (movie) How to install the speed sensor (movie) How to wear the heart rate sensor (movie)
Page 5
Operation of buttons Set up the computer by operating the buttons as follows. Check the button position before you start setting up. Front Back M1/ + MENU M2/- Press the SSE button, the M1/+ but- Press the MENU button on the back ton, and the M2/- button on the front of the computer.
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Preparation for setting up Close Formatting operation Open the battery cover on the back of the computer using a coin, and then pull out the insulation sheet.
Page 7
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Formatting operation MENU Formatting operation While pressing the MENU button on the back of the computer, press the AC button. About 3 seconds Setting the date display later, a test pattern is displayed on the screen.
Page 8
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the date display Formatting operation When the M1/+ button or the M2/- button is pressed, either “YY/MM/DD”, “MM/DD/YY” or “DD/MM/YY” is selected Setting the date display for the date display.
Page 9
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the year Formatting operation Pressing the M1/+ button increases the value (“Year” of the date) flashing, and pressing the M2/- button decreas- Setting the date display es it.
Page 10
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the month Formatting operation Pressing the M1/+ button increases the value (“Month” of the date) flashing, and pressing the M2/- button de- Setting the date display creases it.
Page 11
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the day Formatting operation Pressing the M1/+ button increases the value (“Day” of the date) flashing, and pressing the M2/- button decreas- Setting the date display es it.
Page 12
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the clock display Formatting operation When the M1/+ button or the M2/- button is pressed, ei- ther “12h” or “24h” is selected for the clock display. Se- Setting the date display lect the display of your choice.
Page 13
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the hour Formatting operation Pressing the M1/+ button increases the value (“Hour” of the clock) flashing, and pressing the M2/- button decreas- Setting the date display es it.
Page 14
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the minute Formatting operation Pressing the M1/+ button increases the value (“Minute” of the clock) flashing, and pressing the M2/- button de- Setting the date display creases it.
Page 15
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Entering the tire circumference Formatting operation Enter the tire circumference (mm) of your bicycle with 4 digits using the tire circumference reference table. Setting the date display Pressing the M1/+ button increases the value flashing, and pressing the M2/- button decreases it.
Page 16
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Setting the speed unit Formatting operation When the M1/+ button or the M2/- button is pressed, ei- ther “km” or “mile” is selected for the measurement unit.
Page 17
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Preparation for setting up Now, setup of the computer is completed. Formatting operation For the speed sensor installation, return to Contents and Setting the date display see related videos.
CATEYE V3n Return to Contents Quick Start Manual How to wear the heart rate sensor If the video does not play, please click here. (YouTube movie)
Page 21
CATEYE V3n Return to Contents Quick Start Manual Setting up the computer Tire circumference reference table * Generally, the tire size or ETRTO is indicated on the side of the tire. ETRTO Tire size L (mm) ETRTO Tire size L (mm)
Registering a new sensor IDs of sensors supplied with this device are synchronized. For any other sensors, synchronize the sensor ID according to the following procedure. * The Q series, 2.4GHz digital sensor can also be used. Speed sensor Heart rate sensor ISC-10 HR-10 (SPEED/CADENCE)
Page 23
CATEYE V3n Return to Contents Quick Start Manual Registering a new sensor Switching to the “Searching for sensor ID” screen To “Searching for sensor ID” To “Searching for sensor ID” From the measurement screen, press the MENU button to switch to the Menu screen.
Page 24
CATEYE V3n Return to Contents Quick Start Manual Registering a new sensor Sensor selection To “Searching for sensor ID” To “Searching for sensor ID” Pressing the M1/+ or M2/- button changes the display as “HR”, “SP1”, and “SP2” in order.
Page 25
CATEYE V3n Return to Contents Quick Start Manual Registering a new sensor Start of searching for sensor ID To “Searching for sensor ID” To “Searching for sensor ID” Pressing the SSE button switches to the “Standby for the sen- sor ID” screen. Then, press the RESET button on the sensor.
Page 26
CATEYE V3n Return to Contents Quick Start Manual Registering a new sensor Completion of searching for sensor ID Completion of searching To “Searching for sensor ID” To “Searching for sensor ID” for sensor ID “ID-OK” appears when the computer receives an ID signal from the sensor correctly.