Advertisement
Model AS 9076
Installation Manual
Remote Start Upgrade Module
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents
(1) -Control Module
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Harness
(1) - Four Pin I/O Harness
(1) - Control Switch / Programming Switch
(1) - Ring Terminal
(4) - 1/2" Long Screws
(1) - Pin Switch
(1) - Remote Start Warning Label
(1) - Literature Package
1
128-7760
1 of 16
Advertisement
Table of Contents
Related Manuals for Audiovox 128-7760
Summary of Contents for Audiovox 128-7760
- Page 1 (1) - Four Pin I/O Harness (1) - Control Switch / Programming Switch (1) - Ring Terminal (4) - 1/2" Long Screws (1) - Pin Switch (1) - Remote Start Warning Label (1) - Literature Package 128-7760 1 of 16...
- Page 2 DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS. 128-7760 2 of 16...
-
Page 3: Wiring The 6 Pin Main Power Harness
( when used ) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. Remote Start Connection 128-7760 3 of 16... - Page 4 BLACK w/WHITE Tracer Wire: Control Switch The Black w/ White tracer wire provides ON-OFF control of the Remote Starter. When the Black w/ White wire is switched to a full time ground, the AS-9075 Remote Start Module is operative. When...
- Page 5 Black wire; see Brown w/ Black tracer wire. BROWN Wire: Positive Inhibit Input 1 Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is received from the transmitter.
- Page 6 2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the ignition switch to the VATS control module. White From Remote Start Module White or White w/ Red Trace Wire From Remote Start Module 128-7760 6 of 16...
- Page 7 5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown). NOTE: The above information and following diagram is for the GM VATS system only. For GM PASS LOCK System you will require the Audiovox AS-PASS II Module. General Motors VATS By-Pass Diagram...
- Page 8 3 pin upgrade connector found later in this manual) NOTE:If you are not upgrading a factory keyless entry system and these wires are not used, all three wires MUST BE connected to chassis ground. (See Dark Blue/Black Wire for single trigger input.) 128-7760 8 of 16...
- Page 9 If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running, and in certain instances reengage the starter motor. Lts Flash 3X Lts Flash 4X Default 15Min. 20 Min. 10 Min Steady Tach > 0.5 1.5 Sec 2.0 Sec Diesel 15 Diesel 20 Single Pulse 128-7760 9 of 16...
- Page 10 The lights will flash 4 times. Indicating timed interval mode has been initiated. The vehicle will automatically start every 2 or 4 hours as programmed. To cancel the timed start mode start the vehicle either by RF or by the ignition key. 128-7760 10 of 16...
- Page 11 3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on and start position and have 0 volts with the ignition in the off position. 4. Connect the Green wire to the (Green) or (Green/Orange) tach input of the Audiovox remote start unit. 128-7760...
-
Page 12: Testing Your Installation
3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE. -
Page 13: Park / Neutral Ecm Input
1. Locate the Orange / Black reference wire in the" C2 " connector found at the ECM in GM B Body vehicles or, locate the equivalent reference wire in the vehicle you are installing the Audiovox Remote Start Unit in. - Page 14 E. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit. F. Connect terminal 86 of the relay to a fused +12 volt constant battery source.
-
Page 15: Completing The Installation
COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: 1. If you have not done so already, place the red rubber handle cover over the handle of the control switch for ease of identification. - Page 16 © 2006 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-7760 128-7760 16 of 16...