DMR-EH75VP CONTENTS Page Page 1 Safety Precaution 12.1. Power Supply Block Diagram 1.1. General guidelines 12.2. Analog Video Block Diagram 1.2. Caution for fuse replacement 12.3. Analog Audio Block Diagram 2 Warning 12.4. Analog Timer Block Diagram 2.1. Prevention of Electrostatic Discharge (ESD) to 12.5.
Page 3
DMR-EH75VP 13.22. Front (R) Schematic Diagram 15 Appendix for Schematic Diagram 13.23. Front Jack Schematic Diagram 15.1. Voltage and Waveform Chart 14 Printed Circuit Board 16 Miscellaneous 14.1. Power & Digital I/F P.C.B. 16.1. Abbreviations 14.2. Main P.C.B. 17 Parts and Exploded Views 14.3.
DMR-EH75VP 1 Safety Precaution 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
DMR-EH75VP 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistor-sand semiconductor "chip"...
( As shown in 14.2.1. The Main P.C.B. ) NOTE: The lithium battery is a critical component. ( Type No.: CR2354-1GUF Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
DMR-EH75VP 5 Features 5.1. About DivX 5.1.1. General DivX is a new video compressing format that is applied MPEG4 technology to improve image quality and the compressibility, and it is developed by the DivXNetworks, Inc., Video file of high resolution and the high picture quality can be made though it is a high compressibility.
Page 14
DMR-EH75VP 5.1.3. About DivX DRM Divx file includes file to which DRM(Digital Right Management) is applied and file not applied. This item is a content that relates only in treating file to which DRM is applied. 1. Registration Code display function 2.
DMR-EH75VP 5.2. HDAVI Control (HDMI Link) Pin Name Linked operations by HDAVI Control (HDMI Link) 5.2.1. What is HDMI HDMI is abbreviation of [High-Definition Multimedia Interface], and is digital interface standard for next generation TV corresponding to follows. 1. Non-compressing high quality digital image 2.
Page 16
DMR-EH75VP (2) Seamless GUI 1. Automatic switching to DIGA functions from VIErA functions When [operate DIGA] of VIErA functions is selected, (3) Remote Control Operation input of VIErA is switched to DIGA input automatically Function that operate DIGA by VIErA remote controller and it displays DIGA functions.
Page 17
DMR-EH75VP pressed, VIErA POWER ON/ Input switch/ audio mute is set automatically, and audio sound is output from speaker connected amp. (5) Timer Recording (Reservation Recording) When select [Reserve] of TV GUIDE of VIErA, Reservation information is transmitted by way of HDMI (HDAVI Control), and reservation registration of DIGA is done.
DMR-EH75VP 7 Operation Instructions 7.1. (DVD) Taking out the Disc from RAM-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 7.1.1. (DVD) Forcible Disc Eject 7.1.1.1. (DVD) When the power can be turned off. 1. Turn off the power and press [STOP], [CH UP] keys on the front panel simultaneously for 5 seconds.
DMR-EH75VP 7.2. (VHS) Removing Cassette Tape manually When the cassette tape could not be uninstalled from an electrical malfunction, there are 2 ways to remove a cassette tape. 7.2.1. (VHS) Removal by compulsory unloading. If Service Mode can be activated when the power can not be turned on, this operation is able.
Page 22
DMR-EH75VP 3. Rotate the Main Cam Gear counter-clockwise until just before the unloading will be completed as shown below. . 4. Rotate the Capstan Motor clockwise to remove the slack tape as shown below. 5. Rotate the Main Cam Gear counter-clockwise again to remove the cassette-tape as shown below.
DMR-EH75VP 8 Service Mode 8.1. (DVD) Self-Diagnosis and Special Mode Setting 8.1.1. (DVD) Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held.
Page 24
DMR-EH75VP Error Code Diagnosis contents Description Monitor Display Automatic FL display UNSUPPO Unsupported disc error *An unsupported format disc was played, “This disc although the drive starts normally. incompatible.” *The data format is not supported, although the media type is supported.
Page 25
DMR-EH75VP Item FL display Key operation Mode name Description Front Key Service Mode Setting every kind of modes for servicing. When the power is off, press [VHS *Details are described in “8.1.3. (DVD) to DVD DUBBING], [OPEN/CLOSE] Service Modes at a glance”.
Page 26
DMR-EH75VP Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power is on, press lock/unlock The lock setting is effective until unlocking the [STOP] [POWER] keys...
Page 27
DMR-EH75VP 8.1.3. (DVD) Service Modes at a glance Service mode setting: While the power is off, press [STOP], [VHS to DVD DUBBING] and [OPEN / CLOSE] simultaneously for five seconds (OPERATION SELECT should be set to DVD). Item FL display...
Page 28
DMR-EH75VP Item FL display Key operation Mode name Description (Remote controller key) I/P Switch Switch Interlace and Progressive in EE mode. Initial mode is Interlace Press [1] [4] in I/P Switch mode. *Initial setting is “Interlace”. *I/P are switched alternately.
Page 29
DMR-EH75VP Item FL display Key operation Mode name Description (Remote controller key) RAM Drive Last Error RAM Drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. *For details about the drive error code, refer seconds.
Page 30
DMR-EH75VP Item FL display Key operation Mode name Description (Remote controller key) Front connection Press all front keys and check the connection Press [5] [4] in service mode. inspection between Main P.C.B. and Front key Switches. (1) Each time a key is pressed, segment turned on increases one by one.
Page 31
DMR-EH75VP Item FL display Key operation Mode name Description (Remote controller key) Tray OPEN/CLOSE Test The RAM drive tray is opened and closed Press [9] [1] in service mode repeatedly. *When releasing this mode, press the [POWER] button of Remote Controller more than 10 seconds.
DMR-EH75VP 8.2. (VHS) Self-Diagnosis and Special Mode Setting 8.2.1. (VHS) Self-Diagnosis Functions This model has a self-diagnosis and display function. If the VHS section detects trouble during installation or during use, one of the following Error Codes will automatically appear in the display on VHS side. Error Codes are displayed in the form of a single English letter followed by two numbers, as for example "H01".
Page 33
DMR-EH75VP 8.2.2. (VHS) Special Modes Setting Item FL display Key operation Mode name Description Front Key Tracking Center Tape Tracking is adjusted to center No display. During PLAYBACK, press [CH UP] FIX position. DOWN] keys simultaneously. VHS Service Mode In order to make service easy, a part...
Page 34
DMR-EH75VP Service Contents Contents of Indication on minute Contents of Indication on second Remarks Number Indication for the Mechanism position Ordering for the Motors There are next conditions in this inner data (Real time) (Real time) mode for enable the mechanism...
Page 35
DMR-EH75VP 8.2.4.2. (VHS) Condition for clearing the self-diagnosis history 1. A case of that press the FF key and the EJECT key simultaneously over 5 seconds. 8.2.4.3. (VHS) Indication of the self-diagnosis history. 1. The self-diagnosis histories and its supplementary data could be indicated on the FIP with Service mode of number from 3 to 2.
Page 36
DMR-EH75VP <Supplementary Data 4> (LM Information) Result of request of driving Loading Motor. Display Description There was no change of mechanism position. (Loading Motor was OFF) There was some change of mechanism position. (Loading Motor was ON) 8.2.5. (VHS) Description of Self Diagnosis Memory In this Self-Diagnosis Function, in case error has occurred continuously, maximum of the newest 3 error data are memorized.
Page 37
DMR-EH75VP Tape Type The aim of Tape position between the starting edge and the finishing edge 60 min. or less type (Large Hub) The Tape position is divided into 6 stages between the Tape beginning edge: "A " and the Tape end edge: "5".
DMR-EH75VP 9 Service Fixture & Tools (For DVD) Part Number Description Compatibility RFKZ0168 Extension Cable (Power & Digital I/F P.C.B. - FAN / 3 Pin) Same as E50 / ES30V / ES40V Series RFKZ0327 Extension Cable (Main P.C.B. - Power & Digital I/F P.C.B. / 15 Pin / 40 mm) Same as ES40V Series RFKZ0240 Extension Cable (Main P.C.B.
DMR-EH75VP 10 Assembling and Disassembling 10.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below.
DMR-EH75VP 10.3. Caution with inserting cassette tape when disassembling the unit Note1: For description of the disassembling procedure, see the section 10.4. Note2: Video Cassette might not enter when a strong lighting is applied to VHS Mechanism when Video Cassette is inserted. Please...
DMR-EH75VP 10.4. Top Case 10.5. Front Panel 1. Remove the 4 screws (A) and 3 screws (B). 1. Remove one screw (A). 2. Slide Top Case rearward and open the both ends at rear 2. Unlock tab (A) and tab (B) simultaneously.
DMR-EH75VP Note: 10.7. RAM / Digital P.C.B. Module When attaching Front Panel, in order to hook Cassette Door Opener Lever to Cassette Door, push up cassette door in the direction of arrow and insert a front panel. 1. Remove 3 Screws (A).
Page 44
DMR-EH75VP Note: 3. Put Digital P.C.B. on RAM Drive and remove RAM/Digital RAM/Digital P.C.B. Module as service part has no heat sink P.C.B. Module. unit. Before returning to customer, heat sink unit should be installed on Digital P.C.B..
DMR-EH75VP 1. Remove 2 Screws (A). 10.8. HDD 2. Disconnect the wire with connector from Digital I/F P.C.B.. 3. Remove the 4 Screws (B) and FFC to remove HDD Bracket with HDD. Handling of HDD The following precautions should be taken when handling HDD.
DMR-EH75VP 5. Remove the 4 Screws (C) to remove HDD from HDD Bracket. Note: Pay attention to stiff connections of P2571 and P3001, when removing VTR Mechanism Unit. 10.9.1. Caution for attaching VTR Mechanism Unit 1. Because Position SW should be set to "Eject Position", refer to fig.(A) and set the position switch so that the boss...
DMR-EH75VP 10.11.1.1. Only Fan Motor 10.10. SD Card/DV Jack P.C.B. 1. Disconnect Fan Connector. 1. Remove 7 Screws (A). 2. Remove 2 Screws (A) to Remove Fan Motor. 2. Remove SD Card/DV Jack P.C.B. with Digital Angle. 10.12. HDMI P.C.B.
DMR-EH75VP 11 Measurements and Adjustments 11.1. Service Positions Note: For description of the disassembling procedure, see the section 10. 11.1.1. Checking and Repairing of Power & Digital I/F P.C.B.
Page 50
DMR-EH75VP 11.1.2. Checking and Repairing of Main P.C.B.
Page 51
DMR-EH75VP 11.1.2.1. Checking IR Circuit NOTE1: Even if Main P.C.B. is not removed, IR Circuit can be checked. NOTE2: Prepare the Oscilloscope 1. Remove Top Case. 2. Turn on the power. Then if "Welcome ..." was displayed on the TV monitor, press [ENTER] to advance next stage.
Page 52
DMR-EH75VP 11.1.3. Checking and Repairing of RAM / Digital P.C.B. Module...
Page 53
DMR-EH75VP 11.1.4. Checking and Repairing of HDD...
DMR-EH75VP 11.2. Caution for Replacing Parts 11.2.1. Notice for replacing parts of VHS Mechanism 11.2.1.1. Regarding change of parts of VHS mechanism 11.2.2. Notice for Replacing Capstan Motor...
Page 55
DMR-EH75VP 11.2.3. Items that should be done after replacing parts Note2: Please prepare latest firmware updating disc. * Main Firm is being recorded in HDD, but new HDD has no data. Writing Procedure of Main Firm: <<Caution>> (1) Writing of Main Firm needs 3, 4 minutes.
Page 56
DMR-EH75VP * In a usual updating of firmware, writing is not performed when the timer reservation standby was not released.
Perform auto recording and playback for one minute using the RAM No abnormality should be seen in the picture, sound or operation. disc. *Panasonic DVD-RAM disc should be used when recording and playback. If a problem is caused by a VCD, DVD-R, DVD-Video, Audio-CD, or No abnormality should be seen in the picture, sound or operation.
DMR-EH75VP 12 Block Diagram 12.1. Power Supply Block Diagram VA11101,L11101 L11102 D11101,C11108 T11101 X SW+12.5V SW TRANSFORMER AC SOCKET P11101 F11101 SURGE RECTIFIER SUPPRESSOR SURGE ABSORBER MECHA+12.5V D11210 P31903 P6003 MAIN P.C.B. IC11201 15,16 IC2501- (SWITCHING IC) Q11101 (FEED BACK)
Page 60
DMR-EH75VP IC4801 (REG.+9V) D +3.8V P37101 P59001 60,62 X SW +12.5V P31902 P6004 X SW +12.5V Q11603 IC11602 IC45001 V IN V OUT IC3701- (DR +5V SELECT SWITCH) (HDD PFAIL OUT) (REG.AU +5V) DIGITAL P.C.B. ON/OFF AU +5V P37101 P59001...
DMR-EH75VP 12.2. Analog Video Block Diagram JK3902 REAR A/V OUT JACK IC3701 (VIDEO I/O PROCESSOR) CPN V OUT VIDEO C-SW C75 OUT CPN Y OUT DVD C IN P59001 P37101 P31902 P6004 C OUT DM S-VIDEO 6.7M C75 SAG CPN C OUT...
Page 62
DMR-EH75VP :DVD VIDEO EE SIGNAL :REC SIGNAL :PB SIGNAL IC3001 (AUDIO/VIDEO SIGNAL PROCESSOR) TU7401 2MHz U/V TUNER PACK TW3001 VIDEO ENVE SQUELCH VIDEO OUT -6dB -4dB Q3004 SYSTEM CONTROL SECTION CLEAR OSD V IN -6dB SQUELCH V-AMP SYNC IC6001- VIDEO...
DMR-EH75VP 12.3. Analog Audio Block Diagram DVD AUDIO SIGNAL AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE IC4501 IC3001 FROM (AUDIO PROCESSOR) (AUDIO PROCESSOR) Q4001, D.REC SYSTEM Q4002 QR4001 IC6001- CONTROL SECTION A+5V NORMAL...
DMR-EH75VP 12.4. Analog Timer Block Diagram IC7501 (TIMER CPU) MAIN P.C.B. DP7501 FRONT L P.C.B. < OPERATION KEY > Q7501 PS6001 PP4801 FROM P31905 P6001 DISPLAY DIGITAL I/F P.C.B. DRIVE IC11720- S7801 S7802 CH DOWN FROM P31905 P6001 DIGITAL I/F P.C.B.
DMR-EH75VP 12.5. System Control & Servo Block Diagram MAIN P.C.B. IC0201 (CAPSTAN MOTOR DRIVE) IC6001 (SYSTEM CONTROL/SERVO) MECHA +12.3V P0201 P2571 TL2502 5V(D) 37 CAPSTAN CAP TL MOTOR COILS P0201 P2571 MOTOR DIFFERENTIAL TORQUE CURRENT LIMIT 12MHz IN 38 DRIVE...
DMR-EH75VP 13.6. Digital I/F (1/4) Section (Power & Digital I/F P.C.B.(2/2)) Schematic Diagram (IF) IC45001 X SW+6V SWITCHING REG. LOCATION MAP P:Power Supply Section:(Page: IC-DETAIL BLOCK DIAGRAM IF:Digital I/F Section:(Page: VOUT IC37001 FAN MOTOR DRIVE IC-DETAIL BLOCK DIAGRAM NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.
DMR-EH75VP 13.8. Digital I/F (3/4) Section (Power & Digital I/F P.C.B.(2/2)) Schematic Diagram (IF) L M N O DIGITAL I/F SECTION (1/4) C35001 TO HDMI P35001 R35001 HDMI_CONT K1KY10AA0107 R35002 HOT_PLUG X_SW6V R35003 HDMI_P3_ON_H D3R8V R35008 D3R8V R35004 HDMI_P5_ON_H R35015...
DMR-EH75VP 13.12. Syscon/Servo/Timer (1/4) Section (Main P.C.B.(3/4)) Schematic Diagram (S) TO POWER & DIGITAL P.C.B. TO POWER & DIGITAL P.C.B. LOCATION MAP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. V:Video Section:(Page: THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
DMR-EH75VP 13.13. Syscon/Servo/Timer (2/4) Section (Main P.C.B.(3/4)) Schematic Diagram (S) TO POWER & DIGITAL P.C.B. TO POWER & DIGITAL P.C.B. TO POWER & DIGITAL P.C.B. LOCATION MAP REF_GND IECOUT D_GND GPYOUT_DM RPROUT_DM BPBOUT_DM YOUT_DM COUT_DM V_Y_IN_DM CPNC_IN_DM X_SW12R3V SLICER_VIDEO MIX_L_OUT_DM...
DMR-EH75VP 13.16. I/O Tuner Section (1/4) (Main P.C.B.(4/4)) Schematic Diagram (I) JK3902 K1U717B00006 JK4801 K1U407B00004 LOCATION MAP DVD_R_OUT COM_R_OUT DVD_L_OUT COM_L_OUT DVD_V_OUTCOM_V_OUT DVD_CPN_OUT COM_CPN_OUT QR4802 XN0121600L C4831 C4832 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.
DMR-EH75VP 13.19. I/O Tuner Section (4/4) (Main P.C.B.(4/4)) Schematic Diagram (I) AM AN AO AT AU AV AW I/O TUNER SECTION (2/4) LB7407 ERJ3GEY0R00V LB7403 ERJ3GEY0R00V IF OUT C7421 C7422 6V47 0.01 R7401 1K[D] C7401 IC7402 D7401 50V1 C0CBCDD00006 B0BA03000015...
Page 89
V-SW MUTE R CH C1 IN IIC BUS INTERFACE P-ON V-SW MUTE Y1 IN P-ON IC3701 Detail Block Diagram MUTE C/S DET1 IC4801 Detail Block Diagram IC7301 Detail Block Diagram TUNER IN IC7402 Detail Block Diagram DMR-EH75VP IC-Detail Block Diagram...
DMR-EH75VP 14 Printed Circuit Board 14.1. Power & Digital I/F P.C.B. 14.1.1. Power & Digital I/F P.C.B. Digital I/F P.C.B. DMR-EH75VP Digital I/F P.C.B. (VEP09143AT)
Page 96
DMR-EH75VP 14.1.2. Power & Digital I/F P.C.B. Address Information Digital IF P.C.B. Integrated Circuit D11701 C11606 R11512 R38025 IC11201 D11703 C11607 R11513 R38026 IC11301 D11704 C11608 R11514 R38027 IC11502 D11705 C11610 R11601 R38028 IC11601 D11706 C11612 R11602 R38029 IC11602 D11720...
DMR-EH75VP 16 Miscellaneous INITIAL/LOGO ABBREVIATIONS ERROR TORQUE CONTROL ERROR TORQUE CONTROL 16.1. Abbreviations REFERENCE ENCSEL ENCODER SELECT ETMCLK EXTERNAL M CLOCK (81MHz/40.5MHz) 16.1.1. DVD ETSCLK EXTERNAL S CLOCK (54MHz) FBAL FOCUS BALANCE INITIAL/LOGO ABBREVIATIONS FCLK FRAME CLOCK A0~UP ADDRESS FOCUS ERROR...
Page 114
DMR-EH75VP INITIAL/LOGO ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS READ ENABLE VBLANK V BLANKING RFENV RF ENVELOPE COLLECTOR POWER SUPPLY RF PHASE DIFFERENCE OUTPUT VOLTAGE (CD-ROM) REGISTER SELECT VCDCONT VIDEO CD CONTROL (TRACKING RSEL RF POLARITY SELECT BALANCE) RESET DRAIN POWER SUPPLY VOLTAGE RESERVE...
Page 115
DMR-EH75VP 16.1.2. VHS 4.43 NTSC L 443NT [L] BILINGUAL BILINGUAL L A. COMP AUDIO COMPONENT SIGNAL BIL [L] BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL AUDIO DUBBING PAUSE L BILINGUAL L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 116
DMR-EH75VP CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND [A] GND (ANALOG) DELAIED FM RECORDING L D. FM REC [L] GND [TU] GND (TUNER) D. GND DIGITAL GND GND/N. SW. 12V...
Page 117
DMR-EH75VP POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 118
DMR-EH75VP RF OUT RF OUTPUT SYSCON 5V SYSTEM CONTROL 5V RF Y RF LUMINANCE SIGNAL SYSTEM SYSTEM SW RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP PHOTO TRANSISTOR RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TAKE-UP REEL PULSE ROTAR.
DMR-EH75VP 17.2. Replacement Parts List Ref. Part No. Part Name & Remarks Description C3010 ECJ1VB0J105K 6.3V 1U Notes: C3011 ECJ1XB1C104K 16V 0.1U *Important safety notice: C3012 ECEA0JKA470 6.3V 47U C3014 ECJ1XB1C104K 16V 0.1U Components identified mark have special C3015 ECJ1VB0J105K 6.3V 1U...
Page 124
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description C3739 ECJ1XB1C104K 16V 0.1U C4809 ECEA1CKS100 16V 10U C3740 ECJ1XB1C104K 16V 0.1U C4810 ECEA1HKA4R7 50V 4.7U C3741 ECJ1VB0J105K 6.3V 1U C4811 ECEA1CKS100 16V 10U...
Page 125
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description C7313 ECEA1HKA4R7 50V 4.7U VEE0U97 EARTH WIRE C7314 ECEA1HKS2R2 50V 2.2U C7315 ECEA1HKS2R2 50V 2.2U JK3902 K1U714B00002 JACK,S1/S2 C7316 ECJ1VB1E223K 25V 0.022U JK3903...
Page 126
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description P4002 VJS3537A006G CONNECTOR(FEMALE) K1MN06A00034 R3010 ERJ3GEYJ682 1/10W 6.8K R3013 D0GB103JA057 1/10W 10K P6001 K1KB19AA0033 CONNECTOR(19P) R3014 D0GB102JA057 1/10W 1K P6002 K1KB19AA0033 CONNECTOR(19P) R3017...
Page 127
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R4519 D0GB753JA057 1/10W 75K R4868 D0GB103JA057 1/10W 10K R4520 ERJ3GEYJ472 1/10W 4.7K R4869 D0GB103JA057 1/10W 10K R4521 ERJ3GEYJ511 1/10W 510 R6001 D0GB102JA057 1/10W 1K...
Page 128
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R7543 D0GB103JA057 1/10W 10K W762 ERJ3GEY0R00 1/10W 0 R7544 D0GB103JA057 1/10W 10K W763 ERJ3GEY0R00 1/10W 0 R7546 D0GB473JA057 1/10W 47K W764 ERJ3GEY0R00 1/10W 0...
Page 129
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description W837 ERJ3GEY0R00 1/10W 0 C11605 ECJ2YB1C105K 16V 1U W840 ERJ3GEY0R00 1/10W 0 C11606 ECJ2VB1E104K 25V 0.1U W842 ERJ3GEY0R00 1/10W 0 C11607 ECJ2VB1E104K 25V 0.1U...
Page 130
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description D11303 MAZ73000BC DIODE LB37004 J0JHC0000048 FILTER D11304 MA2J11100L DIODE LB37005 J0JKB0000032 FILTER D11305 B0AADM000003 DIODE LB37006 ERJ3GEY0R00 1/10W 0 D11306 B0BC8R100004 DIODE LB37007 ERJ3GEY0R00...
Page 131
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R11510 ERJ6ENF5602 1/8W 56K R38005 ERJ3GEY0R00 1/10W 0 R11511 ERJ6GEYJ103V 1/8W 10K R38006 D0GB103JA057 1/10W 10K R11512 ERJ6GEYG242V 1/8W 2.4K R38007 D0GB103JA057 1/10W 10K...
Page 132
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R66801 D0GB123JA057 1/10W 12K R66802 D0GB123JA057 1/10W 12K L56101 J0MAB0000170 COIL R66804 D0GB123JA057 1/10W 12K L56102 J0MAB0000170 COIL R66805 D0GB123JA057 1/10W 12K L56103...
Page 133
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R56140 ERJ2GEJ8R2 1/16W 8.2 R56142 ERJ2RKD330 1/16W 33 C7701 ECJ1VF1C104Z 16V 0.1U R56143 ERJ2RKD330 1/16W 33 R56144 ERJ2GEJ8R2 1/16W 8.2 D7701 B3AEA0000082 DIODE...
Page 134
DMR-EH75VP Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description VEE1C37 FFC(40P) VMD4253 LED PRISM VEE1C38 FFC(20P) VML3934 MAIN LEVER VEE1C39 FFC(40P) VML3933 PINCH CHARGE ARM L6FALCCE0016 FAN MOTOR VML3632 IDLER ARM RGR0368B-A...