Panasonic KX-FT932RU-B Service Manual page 57

11.1.3. Service Function Table
Code Function
501 Pause time
502 Flash time
503 Dial speed select
514 Bell detection time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
544 Document feed position adjustment
value set
550 Memory Clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
560 Cutter selection (KX-FT934 only)
561 KEY test
562 Cutter test (KX-FT934 only)
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection time
set
573 Remote turn-on ring number set
574 DIAL TONE detection ON/OFF selec-
tion
590 FAX auto redial time set
591 FAX auto redial time disconnection time
set
592 CNG transmit select
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
Set Value Effective
Range
X 100 msec 001~600 60
X 10 ms 01~99 85
1: 10 pps 1, 2 1
2: 20 pps
X 100 msec 1~9 6
1:2100 Hz 1, 2 1
2:1100 Hz
1:ON 2:OFF 1, 2 1
1:ON 2:OFF 1, 2 1
1: 0 km 1~4 1
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4 1
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 3 mm 1~5 3
2: 4 mm
3: 5 mm
4: 6 mm
5: 7 mm
1:ON 2:OFF 1, 2 2
1:OFF 1~3 1
2:PHASE B
3:ALL
0
1:ON 2:OFF 1, 2 1
1:ON 2:OFF 1, 2 1
1:61% 2:67% 1, 2 1
X number of 00~99 03
times
X second 001~999 065
X number of 01~99 10
rings
1:ON 2:OFF 1, 2 2
X number of 00~99 03
times
X second 001~999 065
1:OFF 1~3 2
2:ALL
3:AUTO
57
Default
----------
----------
----------
----------
See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.83).
See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.83).
The resolution reverts to the default when transmission
is complete.
When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
If it is difficult to feed documents, raise the set value. If
multi documents feed occurs, lower the set value.
See Memory Clear Specification (P.59).
See Test Mode(P.54).
For the DTMF single test, single tone (single tone fre-
quency in the high and low group) are out from the
modem. ON will be DTMF and OFF will be single tone
.After the test, do not forget to return to the ON setting.
Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
See Test Mode(P.54).
See Test Mode(P.54).
See Test Mode(P.54).
See Test Mode(P.54).
See Test Mode(P.54).
Select the jam detection of a document during FAX
transmission/copying.
Turns off the cutter function.
See Test Mode(P.54).
Press "SET" key.
Sets the % break of pulse dialing according PBX.
Selects the number of times that ITS is redialed (not
including the first dial).
Sets the interval of ITS redialing.
Sets the number of rings before the unit starts to
receive a document in the TEL mode.
Sets the whether to dial the Automatic dial number
before detecting dial tone or after detecting dialtone.
Selects the number of redial times during FAX commu-
nication (not including the first dial).
Sets the FAX redial interval during FAX communication.
Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.81).
Remarks