Table of Contents
Advertisement
e PERIPH (peripheral) connector (RJ-45)
Connect to a Device Control Unit
∗ Device Control Unit refers to the DCU-8000-C or DCU-2000-C.
Note
An Ethernet switch is required to connect two or more
Device Control Units.
f EDITOR PANEL connector (D-sub 15-pin, RS-
422A)
Connect a MKS-8050/2050 Editing Keyboard to this
connector.
Note
When you have connected a MKS-8050/2050 Editing
Keyboard to the EDITOR PANEL connector, do not
disconnect and connect the connector.
g REF IN (reference signal input) connectors
(BNC type)
If you wish to synchronize this unit to an external reference
signal, input the reference signal. For an HDTV system,
input an HD tri-level sync signal, black burst signal, or
analog sync signal. For an SDTV system, input a black
burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75Ω terminator.
h REMOTE connector (BNC type)
Connect this connector with a BNC cable to an S-BUS data
link via a T bridge.
An S-BUS data link is a single signaling circuit (S-BUS)
to which multiple devices can be connected to exchange
data.
Connecting devices such as IXS series routing switchers
and remote panels to an S-BUS data link enables the
following kinds of control.
• Returning to the S-BUS, tally data created by this unit on
the basis of data received from other devices
• Switching the cross-points of a routing switcher from the
center control panel
• Switching the cross-points of a switcher from the remote
panel
• Displaying on the center control panel source names set
on a routing switcher
i LTC IN (longitudinal timecode input) connector
(BNC type)
This connector is reserved for future system expansion.
j GPI (General Purpose Interface) connector
(D-sub 25-pin)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
12
Location and Function of Parts
*
with a cross cable.
with input and output conditions set on the center control
panel.
k U (signal ground) terminal
Connect to the system ground.
l - AC IN (AC power input) A and B connectors
(3-pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cords.
Depending on the configuration of your unit, the Backup
Power Supply Unit may not be installed. In that case, the
AC IN B connector is not used.
Caution
For information about installing, contact your Sony
service representative.
m MAIN PANEL connector (D-sub 50-pin,
special interface)
Connect to the SCU connector of the main panel.
n EXT (extension) PANEL 1 and 2 connectors
(D-sub 50-pin, special interface)
Connect to the MKS-8075A Extension Adaptors and AUX
panels to install operation modules apart from the center
control panel.
o MENU PANEL connector (D-sub 50-pin,
special interface)
Connect to the menu panel.
p MENU DISPLAY connector (high-density D-sub
15-pin, analog RGB)
Connect to an SVGA compatible monitor to view the
menu.
CAUTION
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following ports.
- PERIPH (peripheral) connector
- DATA connector
- CTRL (control) connector
Follow the instructions for the above ports.
• When you connect the PERIPH, DATA, and CTRL
connectors of the unit to peripheral device, use a
shielded-type cable to prevent malfunction due to
radiation noise.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive aux ports suivants.
- PERIPH connecteur
Hide quick links:
Advertisement
Table of Contents
