1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. SureColor F6200
  6. Settings manual

Epson SureColor F6200 series Settings Manual

Hide thumbs Also See for SureColor F6200 series:

Advertisement

Table of Contents

See also: User Manual
SureColor F6200 series
Setting Guide (install)
Seiko Epson Corp.
PS CS QUALITY ASSURANCE DEPARTMENT
SE Group Confidential (Related Staff Only) Until: Permanent
1

Advertisement

Table of Contents
loading

Related Manuals for Epson SureColor F6200 series

Summary of Contents for Epson SureColor F6200 series

  • Page 1 SureColor F6200 series Setting Guide (install) Seiko Epson Corp. PS CS QUALITY ASSURANCE DEPARTMENT SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 2 Revision Status Revision Date of Issue Description June 26,2015 Temporary release for unit July 22,2015 First release for MP unit SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 3 IMPORTANCE Please inform the user of the next page certainly! • Please print and pass the next page to user and encourage the points of caution. • SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 4: Ink Refill

    Ink refill ■ Important Check ink levels Replace chip unit with new one attached When this message appears, Shake the new ink pack as shown new ink pack. in the illustration horizontally for check ink level of the tank Ink level is more than 70mm: approximately 5cm left and right which is indicated by Recommends to continue using the...
  • Page 5 < Caution > Always wear gloves for assembly to avoid injury from sharp metal edges. When handling the ink packs Wear protective eyewear, gloves, and mask when performing maintenance. SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 6 1-1 Packaging Blue ones You can use both below. After 100units, This screws will be changed • Silver ones : 2pcs (Running change) • Blue ones : 2pcs First around100units for MP (applied by Blue marker) SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 7: Assembly (Stand)

    Assembly (Stand) It is recommended to assemble the stand by a group of three. Give the screws shown in the figure a couple of turns to fasten the parts temporarily. The items in the following steps can not be attached if the screws are too tight.
  • Page 8 Assembly (Stand) Set the plate to the Stand Right You must set this plate before placing main unit on the stand. Set hex 2pcs bolts temporarily. E x 2 Before using the printer, be sure the stand is fixed in place. When moving the printer, unlock the...

  • Page 9: Assembly (Main Unit + Stand)

    Assembly (Main unit + Stand) When carrying the printer, use at least 4 persons. When lifting the printer unit, only hold the highlighted area. Otherwise, it may affect normal operation and printing. SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 10 Assembly (Main unit + Stand) SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 11: Setting The Ink Support Assy

    Setting the Ink Support Assy. 1. Hook the plate into the holes. 2. Tighten 10 screws. 3 hooks 3 holes C x 10 Main unit bottom front side SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 12 Adjust tank height 1. Loosen 2 screws and make sure the plate is low. 2. Loosen 4 screws and make sure the plates to be able to move up/low and left/right. Full side Home side Loosen Loosen Loosen Loosen SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 13 Adjust tank height 1. Tighten 2 long screws temporarily. Full side Home side Not to touch Temporarily tighten Temporarily tighten 2. Make sure the color index on the plate and Put each CSIC on each slider. IMPORTANCE Slider CSIC 3. Set only Cyan and Black Ink Tanks into Ink Holder as the same order as the color index.
  • Page 14 Adjust tank height *** Set to fit between cut position of Ink Tank and hook of Ink Holder. Please do NOT close cover before adjustment tank height. IMPORTANCE OK!! NG!! Set Ink Tank again 1. Tighten 2 Blue screws temporarily. No need to fix the tank.
  • Page 15 Adjust tank height 2. Insert 2pcs thickness-gauges(2.0mm) 1. Raise the plate softly at 2 locations (Black and Cyan) Tighten 2 screws. with raising the tanks. Cyan Black Black Cyan Tighten 3. Tighten 2 Blue screws to fix the tanks. (Black and Cyan) Cyan Black...
  • Page 16 Adjust tank height – Rough Adjustment 1. Tighten Right Long Screw until the thickness(2.0mm) gauges can be moved smoothly at 2 locations(Black and Cyan) There is gap somehow. 2. Tighten Left Long Screw as the same as the right one. Tank Right Long Screw Left Long Screw...
  • Page 17 Adjust tank height – Detail Adjustment 1. Tighten Right Long Screw until the thickness(2.0mm) gauges can be moved smoothly, AGAIN at 2 locations(Black and Cyan) 2. Tighten Left Long Screw as the same as the right one. Right Long Screw Left Long Screw Tighten to adjust Tighten to adjust...
  • Page 18 Adjust tank height 1. Set the other tanks (Yellow Magenta). 2. Tighten 4 screws to fix the tanks. (Yellow => Magenta => Black => Cyan Tighten to fix Tighten to fix Tighten to fix Tighten to fix Black Cyan Yellow 2.
  • Page 19 Adjust tank height 1. Make sure thickness-gauge(2.0mm) can be passed and thickness-gauge(2.5mm) can’t be passed AGAIN at 2 locations (Black and Cyan). 2.0mm => Can be Passed 2.5mm => Can’t be Passed 2. Check the vertical position 3.Check the front and of Ink Tank rear position of Ink Tank.
  • Page 20 Adjust tank height 1. Tighten 2 screws. Home side Tighten Full side Tighten 2. Push 4 tanks by hand softly. 3. Tighten 2 more screws without pushing hand. Tighten Tighten SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 21: Close The Cover

    Adjust tank height 1. Loosen 2 screws, Again. Loosen Loosen 2. Tighten 2 screws 3. Close the cover. with rising the plate softly. Tighten Tighten SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 22: Setting The Ink Supply Cover

    Setting the Ink Supply cover 1. Hook the Ink Supply cover 2. Tighten 2 screws. on 2 pcs screws. 2 screws Tighten 3. Tighten 4 screws. Tighten F x 2 SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 23 Setting the Waste Ink Tank Holder 1. Hook the plate on the stand and slide to Home side. Waste Ink Tank Holder 2. Tighten 2 screws. G x 2 SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 24 Setting the Waste Ink Tank. 1. Put clamp. Near hole 1-3mm Gap Top of hole SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 25 Setting the Waste Ink Tank. Please put clamp as shown. *** The tolerance of tube length is too big, so please adjust clamp position not to pinch tube. ***Please adjust clamp position not to pinch tube. Adjustable SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 26 Setting the Waste Ink Tank. Make sure the lower clamp is 1. Pass the tube through 2 clamps. between 2 INSULOKs. Upper Clamp Lower Clamp INSULOK 2. Lock Upper Clamp Please place tube as shown. And put waste ink tube and waste ink bottle as shown. SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 27 Setting the Waste Ink Tank. 1. Set Waste Ink Joint 2. Set Stopper. Waste Joint Stopper The lid of the Waste Ink Bottle is required C H E C K 3. Set Waste Ink Tank. P O I N T when disposing of the waste ink.

  • Page 28: Fill Ink Into Ink Tank

    Fill ink into ink tank 1. Shake all ink packs before ink filling ink tank. （Horizontal :5cm (both side) 15times/5sec. 2. Cut the pour spot of ink pack by scissors. Don’t cut deeply. Because this position is guide when pure the ink. SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 29 Fill ink into ink tank 3. Fill the ink tank with the ink from the ink pack. <Caution> Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink  tanks. This can cause messages from the remaining ink warning  system to not be displayed properly. Do not turn on printer before filling all inks. Confirm whether Ink Tank color is suitable for Ink Pack color when  fill the ink.  SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 30 FW update Please do NOT turn on printer before filling all inks! After filling all ink as pictures, please turn on printer by FW update mode. SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 31 FW update 1) Please check the CURRENT FW version. 2) Please update the latest FW. (Printer turn off automatically.) 3) Please turn on the printer by FW update mode again. 4) Please check the FW version which you updated. If OK, please turn off printer. SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 32: Ink Charge

    Ink charge 1. Power ON (Normal mode) 2. Set the printer setting (Language, Calendar etc.) 3. Start Ink Charge after making sure waste ink bottle was set. While Ink charging, don’t touch the printer and covers. Because some bad influence for ink charge process. SE Group Confidential (Related Staff Only) Until: Permanent...

  • Page 33: Nozzle Check

    Nozzle check Check the nozzle check pattern. If you find the nozzle missing, please do cleaning (CL1 or CL2 or CL3). SE Group Confidential (Related Staff Only) Until: Permanent...
  • Page 34 Reference :When you can not proceed ink charge, check the ILS sensor. 1. Turn ON “Service man mode” [Menu]+[ ]+[OK] 2. [SELF TESTING]  [Mecha Adjustment] [Sensor Check] ILS All Color ILS “OFF” C ILS is “ON “ C Ink Tank position is Check again of C Ink Tank position FYI: Normal Power ON mode...
  • Page 35 SE Group Confidential (Related Staff Only) Until: Permanent...

Table of Contents