Table of Contents
Advertisement
Available languages
Available languages
Using no
Adjusting
Using the
Audio Adjustments
Introduction of audio
adjustments
When the non fading output setting is on, the
You can adjust the cut-off frequency and the
The graphic equalizer lets you adjust the equal-
audio signal does not pass through this unit's
Treble level.
ization to match car interior acoustic character-
low pass filter (for the subwoofer), but is output
• In
istics as desired.
and
modes, treble adjustment
FRT1
FRT2
affects only the front output: rear output cannot
through the RCA output.
be adjusted.
Recalling equalizer curves
1 Press
to select non fading output on/off
A
1 Press
mode.
to select
A
Treble
There are seven stored equalizer curves which
When the subwoofer controller setting is
Press
until
appears in the display.
A
Treble
you can easily recall at any time. Here is a list of
• Pressing
, you can select non fading output
on the head unit also per-
Control:EXT
AUDIO
the equalizer curves:
on/off mode. Press
forms the same operation.
until
A
display
AUDIO
in the display.
Shows the audio adjustments status.
Display
• Pressing
2 Select the desired frequency with
on the head unit also per-
AUDIO
1 or ¡.
forms the same operation.
SUPER BASS
Subwoofer indicator
Press 1 or ¡ until the desired frequency
Shows when the subwoofer is on.
POWERFUL
2 Press E to turn non fading output on.
appears in the display.
—
—
appears in the display. Non fading
—
(Hz)
2.5k
NonFad ON
NATURAL
4k
6.3k
10k
Press
to display the audio function names.
A
• Pressing 2 or 3 on the head unit also per-
output is now on.
Press
repeatedly to switch between the follow-
A
VOCAL
forms the same operation.
• You can turn off non fading output by pressing
ing audio functions:
e.
CUSTOM1, 2
(balance adjustment)—
Fad
• Pressing 5 or ∞ on the head unit also per-
3 Press E or e to adjust the treble level.
adjustment)—
(bass)—
Bass
FLAT
Each press of E or e increases or decreases
forms the same operation.
(loudness)—
Loud
Sub-W1
the treble level.
–
+6
–6
(non fading output on/off)—
•
and
CUSTOM1
CUSTOM2
is increased or decreased.
(subwoofer2)/
(non fading output set-
izer curves.
Non Fad
• Pressing 5 or ∞ on the head unit also per-
Adjusting non fading output level
ting)—
(high pass filter)—
• A separate
HPF
CUSTOM1
forms the same operation.
adjustment)
for each source.
When the non fading output is on, you can
• When the subwoofer controller setting is only
• If you make adjustments when a curve other
adjust the level of non fading output.
, you cannot switch the
than
is selected, the equalizer curve
S.W Control:EXT
CUSTOM2
(Refer to page 82.)
settings are memorized in
1 Press
to select non fading output setting
A
• You can select the
• A
curve can be created common to
Sub-W2
CUSTOM2
mode.
Subwoofer output is switched on in the
all sources.
Press
until
A
NonFad 0
• When the subwoofer controller setting is only
• If you make adjustments when the
• Pressing
on the head unit also per-
AUDIO
, you can switch the non fading
curve is selected, the
S.W Control:EXT
CUSTOM2
forms the same operation.
output on/off mode. (Refer to page 82.)
updated.
• You can select the non fading output setting
• When
is selected no supplement or
2 Press E or e to adjust the output level
FLAT
mode only when non fading output is switched
correction is made to the sound. This is useful
of the non fading.
on in the non fading output on/off mode.
to check the effect of the equalizer curves by
Each press of E or e increases or decreases
• Pressing
on the head unit also per-
switching alternatively between
AUDIO
the level of the non fading (e.g.,
forms the same operation.
equalizer curve.
Press E or e until you see the desired value
• When selecting the FM tuner as the source,
displayed.
you cannot switch to
1 Press
on the head unit to display the
SLA
• Pressing 5 or ∞ on the head unit also per-
EQ
• To return to the playback display, press
equalizer mode.
forms the same operation.
.
BAND/ESC
Downloaded from Caradio-Manual.com Manuals
Downloaded from Caradio-Manual.com Manuals
Downloaded from Caradio-Manual.com Manuals
Downloaded from Caradio-Manual.com Manuals
.
S.W
appears
NonFad ON
Equalizer curve
Super bass
Powerful
Natural
Vocal
Custom1, 2
(equalizer curve
EQ
(treble)—
Treble
Flat
(subwoofer1)/
Non Fad
is displayed as the level
are adjusted equal-
Sub-W2
(source level
curve can be created
SLA
Sub-W1
.
CUSTOM1
only when
Sub-W1
appears in the display.
CUSTOM2
curve is
and a set
FLAT
to
).
+6
–6
.
Using the high pass filter
Adjusting loudness
2 Press
on the head unit to select the
EQ
Important
equalizer.
When you do not want low sounds from the
Loudness compensates for deficiencies in the
• If the Multi-channel processor (DEQ-P7000) is
Press
on the head unit repeatedly to switch
EQ
between the following equalizer curves.
subwoofer output frequency range to play from
low- and high-sound ranges at low volume.
connected to this unit, the audio function will
the front or rear speakers, switch the HPF (high
be changed into the Multi-channel proces-
—
SUPER BASS
POWERFUL
1 Press
pass filter) on. Only frequencies higher than
sor's audio menu. For details, see the Multi-
to select
—
A
VOCAL
CUSTOM1
those in the selected range are output from the
Press
channel processor (DEQ-P7000) owner's
until
A
Loud
front and rear speakers.
• Pressing
manual.
AUDIO
Adjusting equalizer curves
forms the same operation.
1 Press
to select
A
You can adjust the currently selected equalizer
Notes
2 Press E to turn loudness on.
Press
until
A
HPF
curve setting as desired. Adjusted equalizer
• If you do not operate the audio function within
• Pressing
Loudness level (e.g.,
AUDIO
curve settings are memorized in
display.
forms the same operation.
about 30 seconds, the display is automatically
.
CUSTOM2
• Pressing 5 on the head unit also performs
returned to the source display.
2 Press E to turn high pass filter on.
the same operation.
• Audio menu functions change depending on
1 Press
to select the equalizer mode .
A
the rear output setting in the initial setting
appears in the display. High pass
HPF 80 Hz
Press
until
A
EQ Low/EQ Mid/EQ High
3 Press 1 or ¡ to select the level.
filter is now on.
menu. Refer to Setting the rear output and
the display.
Press 1 or ¡ until the desired level appears
• To turn high pass filter off, press e.
subwoofer controlleron page 82.
• Pressing
AUDIO
• Pressing 5 or ∞ on the head unit also per-
in the display.
forms the same operation.
forms the same operation.
(low)—
(mid)—
Low
Mid
• Pressing 2 or 3 on the head unit also per-
2 Select the equalizer band you want to
3 Press 1 or ¡ to select a high pass filter
forms the same operation.
adjust with 1 or ¡.
range.
(low)—
EQ Low
EQ Mid
Press 1 and
4 Press e to turn loudness off.
HPF 50 Hz
• Pressing 2 or 3 on the head unit also per-
and
appears in the display.
is displayed. Only frequencies higher
Loud OFF
125 Hz
forms the same operation.
• Pressing ∞ on the head unit also performs
than those in the selected range are output
from the front or rear speakers.
the same operation.
3 Press E or e to adjust the equalizer
• Pressing 2 or 3 on the head unit also per-
curve.
forms the same operation.
.
Each press of E or e increases or decreases
the equalizer curve respectively.
•
–
is displayed as the equalizer curve is
+6
Note
–6
.
increased or decreased.
• If you switch the
• Pressing 5 or ∞ on the head unit also per-
tion is automatically switched off. By switch-
forms the same operation.
ing the
function on after selecting the
H.P.F.
mode, you can combine
SFEQ
with
function.
Note
SFEQ
• If you make adjustments when a curve other
than
CUSTOM2
is updated.
—
—
NATURAL
.
—
—
Loud
CUSTOM2
FLAT
appears in the display.
on the head unit also per-
.
HPF
appears in the display.
on the head unit also per-
) appears in the
Loud Mid
CUSTOM1
appears in
on the head unit also per-
(high)
High
(mid)—
(high)
EQ High
is displayed. Press ¡
mode, the
SFEQ
H.P.F.
function
H.P.F.
is selected,
CUSTOM1
Section
Section
Section
Section
09
09
09
09
or
func-
curve
En
61
Advertisement
Chapters
Table of Contents
