Sony NWZ-S515 Service Manual page 39

Pin No. Pin Name
AA22,
GND
AA23
AA24 TM2
AA25 VANAIN
AA26 VANA
AB1 VDD_L0
AB2 XUSB_OK
AB3 CRD_DET
AB4 CHG_XFLT
AB5 SDR_BA0
AB6 SPIO_XCS1
AB7 NC
AB8 USB_SUSPEND
AB9 IO_C
AB10 to
NC
AB12
AB13 USB_XRST
AB14 USB_INT2
AB15 to MS_DATA3, MS_
AB17 DATA2, MS_DATA0
AB18 MS_INSZ
AB19 WR_LEDCTL
AB20 PM1_SEN
AB21 PM1_CLK
AB22 PM0_SEN
AB23,
GND
AB24
AB25 GND1
AB26 OSCIN
AC1 to
IO_A
AC3
AC4 XCHG_DET
AC5 USB_INT1
AC6 SPIO_XCS0
AC7 SPI0_SK
AC8 SPI0_SO
AC9 IO_C
AC10 to
NC
AC13
AC14 AVDD_LPLL
AC15 AVDD_HPLL
AC16 MS_DATA1
AC17 MS_BS
AC18 MS_SCK0
AC19 NC
AC20 ADA_XRST
AC21 PM0_CLK
AC22 PM0_SO
AC23 PWM0
AC24 VLOIN
AC25 IO_C
AC26 OSCOUT
AD1 NC
AD2 BDID1
AD3 XNC_KEY
AD4 XHOLD_KEY
I/O
- Ground terminal
- Not used
I Power supply input terminal (+2.9 - 4.2V)
O Power supply output terminal (+2.85V)
I Power supply input terminal (+1.2V)
- Not used
I Wake up signal input from the WM-PORT connector
I Fault signal input from the power/charge control
O Bank address signal output to the 256M bit SD-RAM
O Chip select signal output to the FM tuner (NWZ-S615F/S616F/S618F only)
- Not used
O USB suspend signal output to the power/charge control
- Not used
- Not used
O Reset signal output to the USB controller
I Interrupt request signal input from the USB controller
- Not used
- Not used
- Not used
- Not used
- Not used
I L/R sampling clock signal input from the A/D, D/A converter
- Ground terminal
- Ground terminal
I Sub system clock input terminal (32.768 kHz)
- Not used
I Charge detection signal input from the power/charge control
I Interrupt request signal input from the USB controller
O Chip select signal output to the liquid crystal display
Serial data transfer clock signal output to the A/D, D/A converter, FM tuner and liquid crystal
O
display (FM tuner is NWZ-S615F/S616F/S618F only)
Serial data output to the A/D, D/A converter, FM tuner and liquid crystal display
O
(FM tuner is NWZ-S615F/S616F/S618F only)
- Not used
- Not used
I Power supply input terminal (+1.2V)
I Power supply input terminal (+1.2V)
- Not used
- Not used
- Not used
- Not used
O Reset signal output to the A/D, D/A converter
I Bit clock signal input from the A/D, D/A converter
O Serial audio data output to the A/D, D/A converter
- Not used
I Power supply input terminal (+1.8V)
- Not used
O Sub system clock output terminal (32.768 kHz)
- Not used
- Not used
I Key input terminal Not used
I HOLD switch input terminal
NWZ-S515/S516/S615F/S616F/S618F
Description
39